Automotive Brakes Dealers in Amraiwadi, Ahmedabad

A thruster shoe brake has a pair of cast iron shoes which are lined up with friction pads. The shoes are hinged on main arm and side arm of the brake, each of them have a hinge pin fitted in the base. They are connected to each other on top by a tie rod, which is hinged in the main arm and locked to the swivel block in the side arm, by a lock nut. A crank lever is hinged on the main arm and the other end is fixed to the top clevis of the thruster by a hinge pin. A brake spring is fixed on the main arm and is pre-loaded by a locknut on the lever. The pre-tension in this spring decides the braking torque. The thruster is fitted on the base by a hinge pin. When the thruster is not energized, the brake shoes are pressed on the brake drum fitted on the drive motor shaft and hold it under the effect of braking force provided by the spring. In such condition, the brake is applied and the drum cannot rotate. As the piston travels upwards the angle lever turns, pushes the brake rod and compresses the brake spring. Simultaneously, the brake lever on the other side of the wheel (Brake Drum) is retracted. When the first lever reaches the stop on the brake base member the brake lever at the thruster begins to move, releasing the brake drum. Technical Specification

For keeping the quality of the products intact, our quality experts check all levels including procurement of raw materials, production, packaging and dispatch. Based in Gujarat(India), we hold specialization in offering quality products that are the perfect outcome of premium material and modern manufacturing techniques.

Pneumatic brake Powder Brake of various sizes and types are available to fit any applications. They are simple to use, easy to replace worn out brakes pads. Pneumatic brake Powder Brake come fully assembled, ready to fit and easy mounting. All these Pneumatic brake Powder Brake are mainly used as actuators for Un- winder applications

Pneumatic brakes are popularly called as air brakes. They are manufactured in the widest range with electronics to match for continuous slip braking applications at medium power levels. These high-performance, dual disc brakes are characterized by their ability to perform right down to zero speed in open loop or closed loop modes of operation. Pneumatic brake offers wide range of torque proportional to air supply from 0.2 psi to max 90 psi. Breaks produced in the largest range with electronic devices to coordinate for ongoing slide stopping programs at method power levels

Pneumatic brake Powder Brake of various sizes and types are available to fit any applications,All these Pneumatic Brake Powder Brake are mainly used as actuators for Un winder applications,Pneumatic brake Powder Brake come fully assembled, ready to fit and easy mounting.

Magnetic Disc Brakes, electro magnetic disk brakes, disc brakes

• Tonnage: 20 t – 400t
• Length: 1500 mm – 4000 mm
• Thickness: 1.6 mm –20 mm

SALIENT DESIGN FEATURES   Mono block of welded steel frame of ultra tested 2062 steel plates rigid to provide accurate bending. All pivots are hardened of ground pin bushes of lubricated by a central hand pump. Repetitive accuracy is within ± 0.03 mm ram travel parallelism without using sensitive and complex servo hydraulics. Most reliable hydraulic components and sealings of international reputed design for 350 bar against operating pressure of 160 bar maximum. Three cycles of operation inch, single cycle and auto for greater operator convenience. Movable operator console is provided with switches for cycle selection, ram up-down travel, emergency stop and motor on / off. Front operated manual back gauge. Electrical panels and components are provided as per international reputed brands. Precisely panels and manufactured cylinders provide unlimited trouble free working life. Seals can be changed quickly without dismantling the ram or need of crane. STANDARD FEATURE ACCESSORIES   Main drive motor of standard make. Electrical control panel with three speeds inch, single cycle and auto mode of operation. Two front sheet supports. Front operated manual back gauge. Pair of lifting links. Fine stroke adjustment rod with limit switches. One suitable 5 way die and blade. (Segmented or full length, EN-9, Not covered under warrantee) Movable console with emergency stop. Tonnage indicating adjustment device. Manual centralized lubrication system with a hand pump. Bending Chart. OPTIONAL ACCESSORIES   NC Back Gauge Motorized Back Gauge with D.R.O. Finger for standard Back Gauge Automatic Lubrication System.

For Unwind station control for any machines pneumatic Air Regulator operated brake is available as many disc brake required according to load 50 kgs to 1500 kgs. Most important is mounting of the brake in the limited space, which is provided by the user. Requirement is mounting bracket for mounting brake on your Un-winder. This is manually is Air operated no automation is required and far better than spring loaded manual brake. Liner for this brake is replaceable after tear & wear after long time use.

• Material: MS/CI
• Corrosion Resistance: Yes
• Usage/Application: Pneumatic brakes
• Maximum Pressure: 7kg/cm2
• Maximum Braking Force: 4000 N

• Voltage: 400/440 Volts ,3 Phase AC
• Country of Origin: Made in India
• Brand Name: SMI
• Condition: New
• Application: Industrial
• Drum sizes: 100mm to 600mm
• I Deal In: New Only
• Drum Diameter: 4to 30 inch
• Usage/Application: Eot Crane

spring loaded brakes, disk brake, dc brakes, electric motor brake

Electro.Hydraulic Thruster Brake, Double Girder Goliath Cranes

Hydraulic Press Brake, CNC Turning Machining Job Work

pneumatic tension control brake, Belmark Industries

pneumatic tension control brake, Rubber Tube, Web Guiding System

Hydraulic Press Brakes, angle notching machines, special purpose machinery

pneumatic tension control brake, Surface Cooling Roll, Stainless Steel Roller

car brake part & car brakes, plastic bumper, Car Tail Lamp

truck brake, truck engine

Hydraulic Press Brake, Hydraulic Variable Rake Angle Shears