Chemical Pumps Dealers in Gidc Vatwa, Ahmedabad

• Motor Phase: Three Phase
• Type of end use: Industrial
• Power Source: Electric
• Body Material: Cast Iron
• Cooling Method: Air cooled
• Finishing: Paint Coated

METERING DOSING PUMP 0 - 8000 LPH  PRESSURE UP TO 100 BAR  PISTON TYPE DOSING PUMP AND DAIPHRAM TYPE DOSING PUMP WITH ALL  PP, SS 304 , SS 316 , SS316L

We are engaged in offering Chemical Process Pump (FPE-FM Series) to our clients. The Chemical Process Pump we present is designed hydraulically to give high yield and quick performances. We are an eminent Manufacturer, Supplier and Exporter of Chemical Process Pump from Ahmedabad, Gujarat, and we offer it at reasonable rates.   Material of Construction : Pumps are manufactured in variety of materials such as Stainless Steel as per ASTM A 351/743 Gr. CF8, CF8M, CF3, CF3M, CD4MCu, CN7M(Al 20) Duplex Steel as per ASTM A 890/890M Nickel Alloys as per ASTM A 494 / 494M Gr. Hastelloy B – C, CZ 100 (100% Nickel ) Other Alloys: SS 2324 / 2%NiCI / Ni-Resist / D2B / Monel / Inconel 600 / R – 55 / Ni 200 Cast Iron & special Alloy Cast Irons, SG Iron / Ductile Iron. Carbon Steel / WCB. Bronze / Alluminium & Various Non Ferrous Alloys. Constructional features : Pumps are as per DIN 24256 and ISO 2858. The design is of back pull out type. Large variety of models are available to operate at 1450 rpm and 2900 rpm at 50 Hz and 1750 rpm and 3500 rpm at 60 Hz. Casing : The casing has axial suction and top centre line delivery. Smooth hydraulic passages ensure high efficiency. Normal design is for foot mounted pumps. Impeller : The impellers are of enclosed type and semi-open impellers can also be supplied. Hydraulic balancing of impellers is achieved either by back wear ring. The impellers are statically and dynamically balanced. Shaft : The shaft is supported by two antifriction bearings to take residual axial thrust and prevent axial float or radial run out. It is fully protected from the liquid handled by means of a shaft sleeve and PTFE gaskets between impeller nut, impeller hub and shaft sleeve. Stuffing box : The stuffing box is sealed by gland packing or by mechanical seal. Conversion from gland packing to mechanical seal is achieved by changing some standardised parts. Re-machining of stuffing box is not necessary. Bearings : The bearings are oil lubricated. Direction of rotation : Clockwise viewed from driving end. Flanges :   Standard Optional Drilling as per ND 16 DIN ND 10, ND 25 DIN 2533 (Cast Iron-Raised face) ASA 150 BS 10 Table F DIN 2543 (Steel-Plain face) BS 4504-16 bar or 25 ba

• Type: Chemical Process Pump
• Weight: 50-100kg
• Color: BLUE
• Voltage: 220V
• Condition: New
• Automatic Grade: Manual
• Power: AS PER REQ.
• Warranty: 1year
• Pump Power: AS PER REQ
• Pump RPM: BOTH
• Country of Origin: India
• Brand Name: ACTIVE
• Application: AS PER YOUR REQ.

• Country of Origin: India
• Type: Chemical Dosing Pumps
• Voltage: 220V
• Automatic Grade: Semi Automatic
• Power: 1-3kw
• Warranty: 1year
• Pump Power: 10Hp
• Pump RPM: 1400

A chemical dosing pump is a mechanical device that is used to add precise amounts of chemicals, such as acids, alkalis, or chlorine, into a process stream or a container. These pumps are used in a wide range of applications, including water treatment, industrial processes, and agriculture.

• Color: Blue and Orange
• Voltage: 415 V
• Pressure: 8 Kg/cm2
• Power Source: Electric
• Model Name/Number: PMD-X1/ PMD-X2/ PMD-X3
• Usage/Application: Chemical Dosing
• Pump Type: Dosing Pump
• Brand: Premix
• Material: Monel, Alloy 20, Hast alloy B, Polypropylene, Hast alloy C, Titanium, GFT
• Motor Horsepower: 1.5HP
• Max Flow Rate: Up to 1000 Kg/cm2
• Head: 80m
• Phase: Three Phase
• Maximum Discharge Flow: 1000 LPH
• Temperature: Atm.
• Frequency: 50Hz

Operating range: capacity: up to 42 m3hr head: up to 46 meter discharge size: dn 25 to 50 mm temperature: up to 140°c speed: up to 3500 rpm pressure: up to 4.6 kgcm2 applications:  organic inorganic chemical intermediates industries.  pulp & paper, sugar, salt, starch industries.  food, textiles, laminate, cement & steel industries.  pharmaceutical, dyes, textiles, kerosene, diesel & other solvents, caustic.  etp, stp & waste water treatment plant.  eva-operator, scrubber application.  filter press feeding, slurry transfer.  rubber, general industrial services etc.... Materials of construction:  ss-316, ss-316 l, ss-304, ss-304l  duplex stainless steel  super duplex stainless steel  cast bronze, cast steel, cast iron  hastalloy - b & c, alloy-20 etc.....

• Maximum Discharge Flow: 1000 LPH
• Usage/Application: Chemical Dosing
• Material: PP/ SS/ PVDF
• Motor Horsepower: 0.25 to 1 HP
• Max Flow Rate: 15- 1000 LPH
• Phase: Three Phase

This  pump is comparable hydraulic design to any conventional centrifugal pump. Standard dimension process pushes with mechanical Seal/ Glandular  packing arrangement covering all of the chemical sectors.These pumps give you unusual protection against rust & abrasive. We suggest a wide range of Polypropylene Chemical Process Pumps. Polypropylene pumps are a horizontal only last part suction consistent back pull out centrifugal pumps. Polypropylene Chemical Process Pumps series anti-corrosive pumps are supplied with mechanical seal or gland packing arrangement covering 85% of the requirements.      Features Of PolyPropylene Process Pump:- The volute chamber is one piece, grave , joint less design affected from Poly-Propylene Process pumps a chemically still thermoplastic by the use of an absolute moulded process. The entire  wet-end parts are in solid moulded manufacture to with stand corrosion and erosion. The impeller are semi-open type Hydraulically impartial by back vanes, used in our all pumps to suit both obvious & impure fluids. Reserve portion of pumps are made from Poly-Propylene so no deterioration problem can pump leakage. The bearing bracket made from heavy-duty grade cast covered with anti corrosive paint. Reliable fitting of impeller on the shaft by straight  thread. Centrifugal quiet, vibration free. The absolute pump-rotating element can be reserved  towards the motor end without troubling the suction or delivery pipeline, due to back drag out design. The motor stay set to base plate. The pump rotating part can easily be dismantled into its section. After rebuild no time consuming Re-Alignment is required. You will find utmost dimensional inter-changeability in the design of  Pump. This Pumps require least spare parts and save you significant maintenance costs in the long run. Application Polypropylene Chemical Process Pump:- PHOSPHORIC ACID PLANTS : H3PO4, H2SO4, HF and their mixtures with or without solid (gypsum) up to 40% conc. GAS WASHING PLANTS : Scrubbed liquids containing CL2, BR2, F2, I2, SO2, SO3, CO2, NH3 Gases etc. with solids replace hastalloy. RAYON PLANTS : Spin bath solution (H2SO4, ZNSO4, NaSO4, etc.) CAUSTIC SODA PLANTS : Chlorinated brine, conc. HCL, Dilute H2SO4 etc. WATER TREATMENT  EFFLUENT TREATMENT  ELECTRO PLATING  PICKLING IN STEEL ROLLING MILLS  FILTER PRESS FOR DYES  DESCALING  PAPER AND FERTILIZER PLANTS

• Type: Chemical Dosing Pumps
• Application: Chemical Supply

Asha Technocrats – Manufacturer of Chemical Dosing Pump, Chemical Metering Pump, EMEC & Water Powered Chemical Dosing Pump, Chemical Dosing Pump Controller, Electromagnetic, Compressed Air Driven Dosing Pump, Ahmedabad, Gujarat, India.

• Application: Chemical Supply
• Weight: 20-50kg
• Voltage: 220V
• Warranty: 1year
• Pump RPM: 1400
• Body Plastic: Plastic

• Type: Chemical Process Pump
• Application: Chemical Supply
• Weight: 100-150kg, 150-200kg, 200-250kg, 250-300kg, 50-100kg
• Color: Brown, Grey, Light White, White
• Voltage: 110V, 220V, 380V, 440V
• Condition: New, Used
• Automatic Grade: Manual, Semi Automatic
• Power: 1-3kw, 3-6kw, 6-9kw, 9-12kw
• Warranty: 1year, 2years
• Pump Power: 10Hp, 2Hp, 3Hp, 5Hp, 7Hp
• Pump RPM: 1400, 2800
• Flow: Up to 550 M3/Hr
• Speed: up to 3600 RPM

We are engaged in offering a wide range of Air Operated Double Diaphragm Pumps to our esteemed clients as per the quality demands. Our products are as per industry standards, and manufactured by using high grade of raw material.