Compression Testing Machine Dealers in Paldi, Ahmedabad

• Brand Name: EIE

We are offering Compliance with following Intaernational Standards IS : 14858 - 2000 Introduction The digital compression testing machine has been designed to meet the need for a simple, economic and reliable means to test concrete for its compressive strength. The design expressive of simplicity, both of construction and operation, makes the machine easy to use and maintain. The digital machines are provided with a MANUAL pace rate controller, to enable maintain a constant rate of loading. The Complete unit comprises a Loading Unit which is of four pillar model construction, having a cross-head with a spherical seated platen. The lower platen is attached to the top of the piston. The Loading capacity is of 1500 KN, Cubes up to 200 mm & Cylinders up to 150 mm Diameter x 300 mm Height can be tested using the appropriate spacers. The pump facilitates rapid approach of the platens for daylight closure and also provides comprehensive control over the application of load. A control valve provides fine control over the loading rate for accurate pacing. Maximum load is held and retained for approximately 15 minutes, unless cancelled, using the panel mounted reset switch. Salient Features of EIE - Digital CTM Machine · 4 line Alphanumeric display with backlit, displaying - Actual Load, Peak load, Rate of loading and Calculated load in Nmm² · Direct reading of compressive strength in Nmm2 - No calculation required · Peak hold facility · Can manually control pace rate from 1 KNSec to 9 KNsec

The machine embodies an hydraulic system designed to meet the requirements of Indian standards Specification 516-1959 for compression tests on cement mortar cubes up to 7.06 cms. Loading Unit The hydraulic jack of 500 KN capacity is fixed to the base. The upper platen has got a self aligning action and is attached to a screw which passes through the cross head plate, and can be raised or lowered for initial clearance adjustment. The lower platen rests on the jack ram and is positioned with the help of a centring pin. Loading is accomplished by upward movement of lower platen. A dust cover is provided on the jack to prevent any dust from going into the cylinder. A spacer with a centering locating pin is provided to test small specimens. The lower and upper platens of the machine are hardened ground and polished. Guidelines are marked on the lower platen to keep the specimen coaxial with the hydraulic jack. Pumping Unit The motorised pumping unit which is housed in an elegant console is of double plunger type and is driven by three phase 440 volts 50 cycles electric motor. The pumping unit is a seperate unit connected to the jack by means of a steel connecting tube. A junction box is suitably fixed to connect the motor to the mains through a push button starter. The pumping unit is fitted with a 20cm dia, dial hydraulic pressure gauge with 250 division i.e. 0-500 KN X 2 KN. A max red pointer is provided to facilitate taking readings after failure of the specimen. The pressure gauge is fixed at an Angle for easy readability. The machine is fitted with hand wheel control which enables the rate of application of load to varied. The machine is equipped with the facility of Hand Pumping in case of power failure. The electric pumping unit is fixed with a micro-switch to switch off the motor automatically as the load on the machine approaches the rated capacity. Relays are incorporated in the pumping unit so that in case of break down of power supply, the motor will stop and would not re start unless the starting switch is operated. Complete with our own calibration certificate for pressure gauge with National Traceability. Standard Accessories The Machine can be supplied with NCCBM Calibration certificate at an extra cost. The Machine can also be supplied with 2 or 3 pressure Gauges of 100 KN, 250 KN and 500 KN for testing lower strength cubes or smaller size cubes. Optionally, the machine can be supplied with digital load indicator and load cell in place of Pressure Gauge at an extra cost.

EN 12390-4, ASTM C39, AASHTO T22, IS : 14858 (2000) Automatic Test Execution Set test parameters - including load rate and Press the start button The machine automatically starts the rapid approach; switches to the test speed once the specimen comes into contact with the upper platen; automatically release the pressure upon specimen failure Save the test including data results and load-time graph (Optional) Dual stage pump assuring fast piston approach and precise test execution Test execution conforming to EN 12390-4, ASTM C39, AASHTO T22 Controllable pace rate from 1 KN/Sec to 10 KN/Sec. Inbuilt graph in the touch screen display. Auto stop and auto release after completion of each test. Accuracy Class 1 (EN) and Class A (ASTM) starting from 10% of full scale. Soft platen-to-specimen contact and smooth load rate control from the very beginning of the ramp Allow remote verification of settings and performances. For easy debugging of unexpected malfunctions. Complete IP based controller. Working on 240V, 50-60Hz, single phase. Frame Four column high stiffness welded frame tested for stability. Heavy duty spherical seat in lubricating oil bath, allowing initial free alignment at the initial contact with the specimen and automatic jamming up to the end of test. Compression platens Series TM-042-AA fitted with 300 mm dia. platens which are suitable for testing cylinders up to dia. 150x300 mm and cubes up to 200 mm. Surface hardness of platen is 55 HRC, flatness tolerance 0.03 mm. Traceable certificate of surface hardness available on request. Attachment for Paver block testing is available at extra cost. Safety Features Max. pressure valve to avoid machine overloading Piston travel limit switch (Extra cost) Emergency stop button Hardware 132,000 points effective resolution, touch screen graphic display 240 x 128 pixel, sampling rate 50/sec, large storing capacity on USB pen drive test data downloadable to PC, Ethernet port, real time management software (optional). Optional Accessories at extra Cost Dedicated Data manager PC software

• Voltage: 380 V
• Accuracy: +1.0 %
• Power Source: Electric
• Display: Digital

Compression Testing Machines (All Models) Analogue, Digital, Micro Processor Based and Automatic Compression Testing Machines (AIM 302 - AIM 320)   Concrete is a man-made material, essentially mixed at site. The properties of concrete depend on the properties of its ingredients and their proportion and it is likely to  vary from mix to mix. Tests must be conducted, therefore, to ensure that the concrete used is in accordance with design specifications. A frequent test, is the test of compressive strength, in which concrete samples are tested to failure. Compression Testing Machines : Aimil Series Compression Testing Machines are the finest of their types available. Their rugged construction and extreme simplicity makes it possible for even non- echnical personnel to operate them with ease and complete dependability. In particular, the portable units, which are small in dimensions, sturdy and light in weight, make quality control testing possible in areas where commercial testing facilities are not available and where the transportation of larger and much heavier machines would be difficult.Aimil Compression Testing Machines conform to IS: 14858(2000) and calibrated with an accuracy of ± 1% as per the requirement of 1828(Class1) . It can also be supplied as per BS : 1881 and other associated International Standards. These machines are available in 50kN, 100kN, 500kN, 1000kN, 2000kN, 3000kN & 5000kN Capacities. Compression Testing Machines Classification : Analogue models. Digital models with pace rate indicators. Micro Controller based models with automatic pace rate controllers. Fully Automatic models. Salient Features of Compression Testing Machines are : High stability. Self-aligning platen assembly. Load Gauges are calibrated in kN against certified Proving Rings, traceable to NPL / NCCBM. Suitable for testing cubes and cylinders of various sizes. Using special platens, bricks can also be tested. Logged data printing facility through a parallel port interface available in digital and micro controller ased versions. Calibration process accreditated by NABL (National ccreditation Board for Laboratories). Machines with CE mark also available, on special equest. Operator’s safety features like metal door with a erspex window and overload tripping device are  provided in all models. Application Compressive Strength Measurement Industry Civil Infrastructure Cement/RMC Construction Chemicals Dams & Tunnels Fly Ash Irrigation Railways Sleepers Real Estate Refractories Roads, Highways & Bridges Education Architecture Building Technology Civil Department Geotechnical Science Colleges Metal & Material Tiles & Ceramics Special Applications Fly Ash Traffic & Transportation Railways Roads, Highways & Bridges

Compression Testing Hand Operated Machine, Toxicity Tester