Disc Valves Dealers in Odhav, Ahmedabad

• Brand Name: Allines
• Feature: Flanged Ends to ANSI B 16.5 / B 16.47,Meet Inspection requirements as per API 598 / API 6D
• Place of Origin: Ahmedabad  
• Size Range: 4”NB to 20”NB
• Applications: Suitable for all types of water, air and steam 121'C or 250'F
• Condition: New, Good
• Packaging: Bulk

Sand Casting Tilting Disc Check Valves are used to prevent reversal of flow in horizontal or vertical pipe lines. These Sand Casting Tilting Disc Check Valves can be used for upward flow only. The Sand Casting Tilting Disc Check Valves, offered by us, are similar to Swing Check valves. In most installations of Sand Casting Tilting Disc Check Valve, slamming is minimized upon reversal flow. So, noise and vibrations are reduced. We are a prominent Sand Casting Tilting Disc Check Valve Manufacturer, Exporter and Supplier from India. Salient Features : Til Ting Disc Check Valves consists of a cylindrical housing, with a pivoted circular disc The pivots are located just above the center of the disc and offset from the plane of the body seat This design gives a bell – crank action to the disc. The seat is circular bevel type and the disc drops in out of contact without rubbing or sliding Short distance of travel, combined with a balanced disc allows rapid closure while minimizing slamming Pivot pins are constructed of a Stainless Steel Drop tight seating is accomplished over the full pressure range because a slight clearance at the pivot pin assures complete seating between the disc ring and body ring The full flow area with lower head loss ensure with the highest efficiency and durability Meet design requirements as per API 6D / API 594 / BS-EN 12334 / API B 16.34 Meet Inspection requirements as per API 598 / API 6D Face to Face dimensions as per API 6D / API 594 / ANSI B 16.10 Flanged Ends to ANSI B 16.5 / B 16.47 Size Range : 4”NB to 20”NB Options : Single Switch / Hydraulic Cylinder (top, bottom and side mounted) design available on request By – Pass arrangement available on request Applications : Suitable for all types of water, air and steam 121'C or 250'F (For higher temperature, consult factory)

Check valves are self-contained and self-actuating valves that act automatically to prevent flow reversal. REX DCV-Series Disc Check Valves are an excellent alternative to conventional check valves for several reasons. Its design is inherently lighter and more compact, making it less expensive to install and to ship. All valves are seat tested before thery are shipped from the factory. It provides a maintenance free effective solution for preventing reverse flow of condensate discharged from traps. Fit easily between two pipe flanges, can be installed in any direction, with good, tight shut-off. Recommended for all trap installations draining into flooded return lines to prevent return flow especially during a shutdown. REX offers a full line of check valves that are used in a wide range of application for industries such as Oil & Gas, Pulp & Paper, Chemical, Petrochemical, Refining, Mining, Power, Heating, Air Conditioning, Cooling, Timber, Iron & Steel, Textile & many more industries. THE BENEFITS Wide range of uses across a variety of fluids such as, liquids gases & vapours. The unique cam design of the body, enables it to fit between a wide varieties of flanges. The disc is spring assisted. This design is much more efficient in reducing pressure drop, drastically reduces water hammer. Simple & compact design, choice of metal-to-metal or soft seals, use of approved stainless steel materials and quality manufacture, makes it versatile.

Size:2"-36" Class:150#-1500# Material:Carbon steel;Stainless steel;Duplex steel;Bronze;Inconel Medium:Oil;Gas;Water Design&Manufacture to API6D&BS1868 Face to face to ANSI B16.10 Ends to ANSI B16.5 Test&Inspection to API598

Simex offers the wide array of disc check valves which are having compact wafer design and low cost that made it a popular choice when space and price are major factors in valve selection. Our disc check valves are recommended after traps discharging into closed systems to guarantee against return or spill back. Dcvs feature a compact and rugged stainless steel design and are suitable for any process liquid & gas, not just steam. Main advantage of these check valves is they can be mounted between pipe flanges in any direction. Disc check valve which is having the movable disc that block the flow or allow forward flow. The seat opening cross-section may be perpendicular to the centerline between the two ports or at an angle. Although the disc check valves are available in various sizes in order to meet the requirements of different applications. The valve allows full, unobstructed flow and automatically closes as pressure decreases. These valves are fully closed when flow reaches zero, in order to prevent backflow.

• Pressure Rating: ASME- 150#, 300#, 600#
• Size Range: 50 NB through 900 NB

Dual disc check valve are specially designed to minimize pressure drop. Due to its simple and compact design, it requires minimum installing space. It can be installed vertically or horizontally. We offer alternate materials for different applications. It is available with standard as well as customized configuration

• Construction :: Investment casted, slim seal, wafer type, double offset disc
• MOC :: WCB / CF8 / CF8M / CF3 / CF3M
• Size Ranges :: 40 NB TO 300 NB
• Design and Mfg Std :: API 609
• Inspection And Testing Std :: API 598
• Face To Face :: API 609 ‘B’
• End Connection :: Wafer type – suitable to fit between two flanges
• Pressure Rating :: ASA 150 #

Spherical Disc Type Butterfly Valves are giving extremely high performance at very lower operating torque with some significant features like lower weight, compact design, replaceable seat and easy maintenance. PTFE seat ensures smooth working life under temperature up to 210° centigrade. For higher size, these valves are strongly recommended.

• Material: Wooden,Aluminium,Thermocal
• Pressure: 150-psi To 740-psi Cold Working Pressure.
• Port Size: 1'' To 6''inch
• Application: Industrial
• Brand Name: Advance Valves
• Valve Size: 1'' To 28''inch
• Operator: Electric Actuator
• Operation Type: By Actuator

• Pressure Rating: ASME- 150#, 300#, 600#
• End Connection: Sandwich/ Flanged
• Size Range: 50 NB through 900 NB
• Type: Dual Disc Fully Rubber Lined/ Unlined Body
• Operation: Automatic with Return Pessure
• Port Opening: Full
• Seat: Soft - Rubber/ Metal to Metal
• Disc: Dual Disc Spring Loaded
• Gasket & Packing: Graphite/ PTFE
• MOC: Refer Material Chart
• Design Code: API - 594
• Testing: API - 598
• Inspection: 3rd Party/ Client/ Manufacturer

Non Slam Disc Check Valve

Disc Butterfly Valve, Wafer Type Double Eccentric Disc Butterfly Valve, Replaceable PTFE Seated Butterfly Valve, Renewable Teflon Seat Butterfly Valve Spherical Disc - Double Offset Disc - Eccentric Disc Design Butterfly Valve Flow Control Lever Operated - Model Series: WBFSP1/6Double Offset Disc - Eccentric Disc - Spherical Disc Design Butterfly Valve Gear Operated - Model Series: WBFSP1G/6GEccentric Disc - Spherical Disc - Double Offset Disc Design Butterfly Valve Pneumatic Actuator Operated - Model Series: WBFSP1P/6P Double Offset Disc Butterfly Valve Manufacturing Size Range:  DN25/25mm/One Inch, DN40/40mm/One and Half Inch, DN50/50mm/2”/Two Inch, DN65/65mm/2-1/2”/Two and Half Inch, DN80/80mm/3”/Three Inch, DN100/100mm/4”/Four Inch, DN125/125mm/5”/Five Inch, DN150/150mm/6”/Six Inch, DN200/200mm/8”/Eight Inch, DN250/250mm/10”/Ten Inch, DN300/300mm/12”/Twelve Inch, DN350/350mm/14”/Fourteen Inch, DN400/400mm/16”/Sixteen Inch, DN 450/450mm18”/Eighteen Inch, DN500/500mm/20”/Twenty Inch, DN550/550mm/22”/Twenty Two Inch, DN600/600mm/24”/Twenty Four Inch size.   Zero Leakge, High Performance, Spherical Disc, Dual Eccentric Disc, Double Offset Disc Butterfly Valve have been developed with extensive application, design and manufacturing expertise. Nivz make High Performance, Renewable PTFE Seat, Wafer Type - Flangeless Butterfly Valves are reliable, maintenance free shutoff with permanently gas-tight seal with an replaceable Teflon or Elastomer Rubber Seat. Double Offset Disc Butterfly Valve wafer type body having two nos. flange locating holes for sizes up to 12” and from size 14” and above 04 nos. for easy alignment of valve during installation. Flange locating hole confirm to as per ANSI B 16.5 Class 125 & Class 150 / BS 10 Table “D”, “E”, “F” / PN 6, PN 10, PN 16 or other international standard. We are also manufacturers and exporters of Double Flanged End Double Offset Disc Butterfly Valves with renewable type seat with Flow Control Lever, Gear, Pneumatic Actuator, Motorized Electrical Actuator Operated. Spherical Disc Type butterfly valves excess other conventional valves such as gate valve and globe valves in all aspects, especially in terms of light weight, less number of component, no flange gaskets required and economical operation and maintenance costs. Our manufacturing range of Double Eccentric Disc Design Butterfly Valves body seat mechanism have a very low torque, tight shut off with zero leakage, compact actuator selection, and long life smooth easy operation. High Performance type eccentric disc design valves are widely available with different combination of body, seat & disc materials to satisfy the need of most industrial application. We manufacture and exporting zero leakge, dual eccentric disc butterfly valves with variety of elastomer rubber seat to suit various industrial application. Our seat range of elastomer covers EPDM, NBR, Buna-N, Nitirle, Silicon, Viton, Hypalon, PTFE. Our Size range of Butterfly Valve cover up to 24" (DN600/600NB/600MM) Size. Nivz Valve & Automation also manufacturing butterfly valves in special grade of material like CN7M-Alloy20, Nickel Aluminium Bronze, NAB2, Hastelloy C22/276, Monel, SS304L, SS 316L, SS317L, D2205, D2507, 4A, 5A & Super Duplex Steel for Sea Water & Corrosive application. Butterfly Valve Various Operation Option Nivz make Slim seal design center disc zero leakge wafer type body Butterfly Valves are generally supplied with manual flow control hand lever operation up to 8”(DN200) and above size valve quarter turn worm gear unit operated. Nivz Valves & Automatin also offering Butterfly Valves with either Pneumatic or Motorized Electrical actuator (single phase or three phase) operated for automation. Remote operated butterfly avaliable for ON/OFF as well praportional modulating control function with required all accessories. We are also manufacturing of Quarter Turn Worm Gear Operated Double Offset Butterfly Valve, Pneumatic Actuated Eccentric Disc Butterfly Valves, Pneumatic Actuator Operated Spherical Disc Butterfly Valves, Double Acting Actuator Operated Dual Offset Disc Butterfly Valve, Single Acting Spring Return Actuator Operated Wafer Type  Butterfly Valve, Electrical Actuator Operated Offset Disc Design Butterfly Valve, Motorized actuator Operated Spherical Eccentirc Butterfly Valve, Remote Operated High Performance Butterfly Valve, On-Off Butterfly Valve Double Flanged End, High Performance Butterfly Control Valve, Modulating Type PTFE Seated Butterfly Valve, We can do provide any of automation in Butterfly Valves.  We have more than 20 years of experience industrial process system field automation. Butterfly Valve can also available with accessories like Gear Box, Solenoid Valve, Air Filter Regulator, Silence, Manual Override, Valve Positioners, Relay etc. We are one of the leading Butterfly Valve Manufacturers Exporters Supplier Stockiest in India. Nivz Valves a best quality Butterfly Valve Manufacturer, Stockist, Supplier, Exporter, Importers.   Salient Features of Double Offset Disc Butterfly Valve Flangless - Wafer - Sandwich Type Greater Sealing Capacity Soft Seat Design, Easy to replace Lower Torque with any fluid Permanently tight closure Uni-Directional Valve Suitable for On-off as well as Throttling Service Materials for almost all media Short Face To Face Dimension Wafer compact design Body Long Service Life Smooth, Easy Operation Maintenance Free Version Less Weight, Easy To Install Leakage Class VI (Zero Leakage) Application of Spherical Disc / Double Offset Disc Butterfly Valve Pharmaceutical Industries Water Treatment Plant Cement Plant Thermal Power Plant Paper Industry Tyre Manufacturing Plant Sugar Industry Breweries Chemical Industry Waste Effluent Treatment Plant Drilling Rigs Gas Plant Steel Plant Cooling Water Circulation Heating & Air Conditioning Pneumatic Conveyors Compressed Air Cement Plant Air Silo

We are offering disc check valve. Technical specifications : design : disc type – non slam single plate check valveseat material : metal seatedbody material : cf8 (ss 304), cf8m (ss 316)end connection : fitted between two flanges.pressure rating class : asa 150, 300, 400, pn 10, pn 16 & pn 40size range : 15mm to 150mm.

We are offering center disc lug type butterfly valve. design feature the unique center line seat and disc design insures positive valve sealing while maintaining low seating torque. all center line butterfly valve discs are precision machined to a half ball profile, providing a precise disc to seat relationship. center line’s cartridge style seat incorporates an elastomeric bonded to a phenol stabilizing ring, eliminating elastomeric movement and reducing seat tearing or fatiguing due to bunching. center line’s basic three bushing design completely isolates the valve shaft from the body, resulting in increased control of the valve disc, lower valve seating torque, and longer valve life. the center line cartridge seat has a much smaller mass of elastomeric than traditional boot seat designs, limiting seat swell and the accompanying variations in seating torque.

FFV Disc Check Valve make in Investment Casting SS 304,SS 316 With Spring Loaded,Soft Seated Teflon.   Features Disc Check Valve(Non Slam Check Valve)Open And Closed Quickly Against the Opposite Flow Acting On Disc & Provide The Full Flow In Line It Occupy very less space and provide full flow. Light weight and easy installation Spring will prevent the reverse flow in pipe lines Zero leakage with soft seated Testing Standard: API 598

• End Connection: FITTED BETWEEN TWO FLANGES.
• BODY MATERIAL: CF8 (SS 304), CF8M (SS 316)
• DESIGN: DISC TYPE - NON SLAM SINGLE PLATE CHECK VALVE
• SEAT MATERIAL: METAL SEATED
• PRESSURE RATING CLASS: ASA 150, 300, 400, PN 10, PN 16 & PN 40
• SIZE RANGE: 15mm to 300mm

The Check Valves have two openings in the body, one for fluid to enter and the other for fluid to leave. These Check Valves are used for diverse purposes. Moreover, we offer the Check Valves in different types and sizes. Features - Two openings- High performance- Superior quality- Made from high grade material 

• Minimum Order Quantity: As per Customer Needs

Disc Check Valve Non Slame, Double Gland Pulp Valve, GLOBE VALVE, FLANGED END

Double Offset Disc Butterfly Valve, Metal seat butterfly valve

Single Disc Spring Loaded Check Valves

fabricated basket strainers, jacketed valves, Pinch Valves, Air Valves

Disc Check Valves, Non Return Valves

Double Offset Disc Butterfly Valve, Wafer Butterfly Valve, LUG TYPE BFV

offset disc butterfly valve, Ball Valve