Kisan Irrigations & Infrastruture Ltd. Ashram Road, Ahmedabad, Gujarat

The use of PVC for production of pipes is one of the most important development in helping to fulfill the basic need of clean and hygienic water. Kisan (aka TrimurtiKSR) uPVC pipes are made from highest grade quality resin. Kisan (aka TrimurtiKSR) Self socketed pipes have one end self socketed and the other end plain, which fit snugly, doing away with the need for couplers.

Kisan (aka trimurti ksr) elastromeric pipes are the latest in technological innovations from kisan. Solvent cement is the most commonly used material for jointing pvc pipes. But solvent cement poses innumerable problems.

Even in heavy land areas, where only the strongest galvanized iron, cement and asbestos survive; plastic, in the form of High Density Polyethylene (HDPE) has scored beyond doubt.

In order to tap the underground water resources, the most critical requirement while digging the borewell tubewell is of the rising main pipes. These pipes must have the ability to withstand high tensile loads. The most suitable & time tested material that meets this demand is uPVC, due to its inherent properties over galvanised pipes.

Today, boretube wells are widely accepted as the suitable means of tapping water resource from the depths of the earth. uPVC casing pipes, due to their desirable performance characteristics have been recognized as the most suitable material for bore tube well construction. This is the outcome of the inherent advantages of uPVC casing pipes over conventional MS Casing pipes.

Solvent Cement is used to join two or more pipes or join a pipe to a fitting or a fitting to a fitting.Solvent Cement is available in plastic bottles of 25ml, 50ml, 100ml, 250ml, 1Ltr, and 30Ltr cans. It is also available in aluminum tubes of 25ml, 50ml, and 100ml.

Highly Flexible and light weight The transparent hoses show inner movement Good resistance to chemicals, pressure and abrasion, ideal for transporting powders and granular materials

In a short span of time Kisan Irrigation has produced the largest range and sizes of injection moulded PVC fittings in the country. The fittings, confirming to as per IS standards, are made from the highest grade quality resin. PVC fittings ensure easy installation, quick modifications as well as complete flexibility in constructing a piping system.

Pvc Ball Valves are made from the highest quality grade of Pvc Resin. Its main function is to control the flow of water.

Micro Irrigation Methods are the pressurized Irrigation Systems consisting of Drip & Sprinkler Irrigation. In Micro Irrigation water from water source is lifted by a pumping unit & conveyed directly to field by closed conduit piping net work without any conveyance losses.

Sprinkler irrigation is a method of applying irrigation water which is similar to natural rainfall. Water is distributed through a system of pipes by pumping at pressure above 2 kgcm2 and then sprayed into the air through sprinklers so that it breaks up into small water drops which fall to the ground.

Kisan Mini Sprinklers can be used for marginal water and marginal land irrigation requirements.

In the process of fertigation chemigation, fertilizer is applied directly with the irrigation water. Therefore, wherever the water goes, the fertilizer goes with it. Fertilizer is applied only where needed, and in the proper quantities. The obvious advantages of fertigation, therefore, are the saving of labor and machinery, and the efficient use of the costly chemicals and fertilizers to be applied.

Galvanised Iron Pipes have been in use for the past few decades for the distribution of portable water. The quality of these pipes had deteriorated so drastically over the past decade, that environmentalists and public health engineers had to search for a proper replacement to overcome

PPR-C means Polypropylene Random Copolymer (-CH2- CH-) n CH3 Kisan PPR C plumbing pipes is the right choice for hot and cold water distribution, proven worldwide due to its combining performance Durability, Reliability, Safety with Cost Saving. Kisan PPR-C Pipes & Fittings are manufactured from PPR-C Type 3 having low melt flow rate, high molecular weight and excellent creep resistance which gives long term performance under mechanical stress.

1. Contamination of water due to corrosion, algae formation, roots penetration etc. 2. Reduced flow with passage of time resulting in choked lines. 3. Leakage due to galvanic action and corrosion etc.

For easy installation of SWR Pipes & Fittings always use KSR Rubber Lubricants. This is available in easy & convenient packing from 50 gms to 1 kg.

Conduit Pipes are manufactured from a specially formulated un-plasticized polyvinyl chloride to meet most stringent Indian and International standards. The products are manufactured in accordance with IS:9537 Part 3, BS: EN 61386-21 for uPVC conduits IS:3419.

KSR SWR systems have been quickly replacing the conventional systems that are being used in the building industry. The pipes and fittings are extremely light in weight, strong, durable, dimensionally stable and are safe in handling, transportation and installation. They also have high impact strength. The trouble free performance of SWR pipes & fittings saves a lot of inspection and maintenance cost.

We offer higher diameter pe pipes. Even in heavy land areas, where only the strongest galvanized iron, cement and asbestos survive; plastic, in the form of high density polyethylene (hdpe) has scored beyond doubt.