Magnetic Components Dealers in Odhav, Ahmedabad

With rich experience of this domain, we have established ourselves as a prominent manufacturer and supplier of Magnetic Drum Pulley. Widely used in ceramic and chemical industries, our offered magnetic tool is developed by experienced professionals using optimum grade raw material. In addition to this, we also customize this magnetic pulley in different sizes as per specific demand of the customers. Our offered Magnetic Drum Pulley is widely acknowledged and demanded in the markets owing to its reliable operation and optimum functionality. Features: Easy to fit Robust construction Resistant to corrosion

• Material: MS, Stainless Steel
• Condition: New
• Warranty: 1 Year
• Use: Industrial
• Finishing: Polished
• Adaptive belt width: 400

Features The magnetic pulleys can be installed easily at conveyor discharge They give complete magnetic protection over the entire face of the pulley for removing ferrous contaminants For different conveyors the magnetic pulleys of different sizes are available The pulleys either use ceramic magnets or powerful rare earth magnets General Specification Flux density: 8500 ± 200 gauss Maximum operating temperature 450?C In all pulleys, best grade St. Ferrite/Rear Earth magnets are used for construction. The outer face and the end plates of the magnetic pulley are made out of stainless steel The magnetic pulley removes contaminants like nuts, bolts, wire, tools etc. It protects equipment, and product from the hazards of tramp iron Types High Intensity – (NdFeb Magnet – 8500 Gauss) Low Intensity - ( Ferrite Magnet - 3500 Gauss) Customized Pulley DesignsShree Vishwakarma Magnets also makes custom designed Magnetic Pulleys to precisely fit customer’s application. Following information is required: Type of material Conveyor belt width Belt Speed Size and concentration of the contamination Burden depth InstallationInstallation is often very simple. Four bolts on a set of pillow block bearings normally hold the pulley in place. Loosen the conveyor belt, remove the old pulley and install the magnetized pulley. This type of installation does not require electricity.

• Material: Stainless Steel
• Application: Industrial
• Standard Lift: 3 m
• Capacity: 3 ton
• Hardness: 30 - 60 Shore A
• Working Life: More Than 3 years

Buy the best quality Magnetic Pulley that is the perfect outcome of the best practices and the innovative techniques. Working in close coordination with the genuine logisticians, we dispatch the products in the dedicated time.

• Type: Motorized
• Color: Green
• Material: Metal
• Shape: Round
• Capacity: 0.5 ton, 1 ton, 3 ton, 4 ton, As Per Requirement
• Surface: Polished

Our well-structured warehouse is properly maintained and equipped with modern amenities, thus assist us wholly in meeting bulk requirements of the customers. The packaging commences under the strict supervision of experts and other team members; they ensure that the products are packed sternly to circumvent loss during transit.

"AANAL MAGNETIC" manufacture a wide range of Rare Earth and Ferrite Magnetic Pulleys. These Pulleys are widely used to remove tramp iron mixed with the material moving on a conveyor belt. The permanent magnetic pulley is dual-purpose equipment used for protection of crusher Jaws or other machinery and also for purification and concentration of magnetic material from the mines. It has the widest application in food, chemical, ceramic, paper, coal handling, foundry operation and mining industry. The magnetism in a Permanent Magnetic Pulley is generated by internal assembly of magnets enclosed in non magnetic Stainless Steel shell. The steel shaft is extended on both sides. One side is provided with Key-way. The Pulleys have a face width of 50 mm to 100 mm more than the belt width.  The magnetic strength of the pulley depends on the diameter and also quality of magnets used.  Pulleys with Rare Earth Magnets can handle depths up to 300 mm. Pulley width is determined by width of conveyor belt to be used. Diameter depends on depth of material and speed of the conveyor.  It can be designed to suit custemers specificapplication. The magnetic Drum pulley replaces the drive pulley at the end of conveyor belts. In view of the wide variety of conveyor belt types, the drum pulley are supplied made to measure and ready for installation. As the figure clearly show, the magnetic head roller extracts the iron particles from the material flow and carries them to the underside of the belt where they are removed and collected. Head roller magnets for conveyor belt are supplied in permanent magnets.             Features 304 stainless steel faces. Removable mild steel shaft. Four hub styles. Flat face. Key way and set screws.         Options: Taper locks Crowned face Fixed shaft Lagging Stainless steel shaft

The magnetic Drum pulley replaces the drive pulley at the end of conveyor belts. In view of the wide variety of conveyor belt types, the drum pulley are supplied made to measure and ready for installation. As the figure clearly show, the magnetic head roller extracts the iron particles from the material flow and carries them to the underside of the belt where they are removed and collected. Head roller magnets for conveyor belt are supplied in permanent magnets.

“KUMAR” manufacture a wide range of Rare Earth and Ferrite Magnetic Pulleys. These Pulleys are widely used to remove tramp iron mixed with the material moving on a conveyor belt. The permanent magnetic pulley is dual-purpose equipment used for protection of crusher Jaws or other machinery and also for purification and concentration of magnetic material from the mines. It has the widest application in food, chemical, ceramic, paper, coal handling, foundry operation and mining industry. The magnetism in a Permanent Magnetic Pulley is generated by internal assembly of magnets enclosed in non magnetic Stainless Steel shell. The steel shaft is extended on both sides. One side is provided with Key-way. The Pulleys have a face width of 50 mm to 100 mm more than the belt width.  The magnetic strength of the pulley depends on the diameter and also quality of magnets used.  Pulleys with Rare Earth Magnets can handle depths up to 300 mm. Pulley width is determined by width of conveyor belt to be used. Diameter depends on depth of material and speed of the conveyor.  It can be designed to suit customer’s specific application.The magnetic Drum pulley replaces the drive pulley at the end of conveyor belts. In view of the wide variety of conveyor belt types, the drum pulley are supplied made to measure and ready for installation. As the figure clearly show, the magnetic head roller extracts the iron particles from the material flow and carries them to the underside of the belt where they are removed and collected. Head roller magnets for conveyor belt are supplied in permanent magnets.Features:(1) 304 stainless steel faces.(2) Removable mild steel shaft.(3) Four hub styles.(4) Flat face.(5) Keyway and set screws. Options:(1) Taper locks(2) Crowned face(3) Fixed shaft(4) Lagging(5) Stainless steel shaft

We are offering magnetic pulleys have following features: 1. The magnetic pulleys can be installed easily at conveyor discharge. 2. they give complete magnetic protection over the entire face of the pulley for removing ferrous contaminants. 3. for different conveyors the magnetic pulleys of different sizes are available. 4. the pulleys either use ceramic magnets or powerful rare earth magnets.

we are offering Rare Earth Magnetic Drum Pulley. The magnetic Drum pulley replaces the drive pulley at the end of conveyor belts. In view of the wide variety of conveyor belt types, the drum pulley are supplied made to measure and ready for installation.

Head Pulley Magnets provide continuous self cleaning on products conveyed by belt. As product is conveyed along the belt it reaches the head pulley and enters the magnetic field where metal contaminants are attracted and held tightly to the belt surface. As the belt is conveyed around the magnetic pulley, metal contaminants are held in place until they pass through the magnetic field where they are safely discarded separate from the clean product. A diverter is typically installed below the pulley to direct the metal contaminants away from the cleaned product.   Construction : 304 stainless steel face Bored and keyed hubs Permanent ceramic magnet material All welded rugged construction Keyed shafts Axial or radial pole magnetic circuit.   Features : Available with or without shaft Several hub styles Lagged face Crowned face Taper lock hubs Stainless steel shafts High energy rare earth magnet material Custom sizes available Polarity options.

The magnetic Drum pulley replaces the drive pulley at the end of conveyor belts. In view of the wide variety of conveyor belt types, the drum pulley are supplied made to measure and ready for installation. As the figure clearly show, the magnetic head roller extracts the iron particles from the material flow and carries them to the underside of the belt where they are removed and collected. Head roller magnets for conveyor belt are supplied in permanent magnets.     The version with permanent magnets are fitted with powerful and An-Isotropic Hard ferrite Magnets /high intensity Rare Earth Nd-Fe-B Magnets and operate without the need for power supplies. The magnet system is available in two types: with Longitudinal polar field distribution for use with low levels of iron contamination and thin material layers, and with lateral polar field distribution for greater material thickness and larger iron particles.   

Head Pulley Magnets provide continuous self cleaning on products conveyed by belt. As product is conveyed along the belt it reaches the head pulley and enters the magnetic field where metal contaminants are attracted and held tightly to the belt surface. As the belt is conveyed around the magnetic pulley, metal contaminants are held in place until they pass through the magnetic field where they are safely discarded separate from the clean product. A diverter is typically installed below the pulley to direct the metal contaminants away from the cleaned product. Construction : 304 stainless steel face Bored and keyed hubs Permanent ceramic magnet material All welded rugged construction Keyed shafts Axial or radial pole magnetic circuit. Features : Available with or without shaft Several hub styles Lagged face Crowned face Taper lock hubs Stainless steel shafts High energy rare earth magnet material Custom sizes available Polarity options

The magnetic Drum pulley replaces the drive pulley at the end of conveyor belts. In view of the wide variety of conveyor belt types, the drum pulley are supplied made to measure and ready for installation. As the figure clearly show, the magnetic head roller extracts the iron particles from the material flow and carries them to the underside of the belt where they are removed and collected. Head roller magnets for conveyor belt are supplied in permanent magnets. The version with permanent magnets are fitted with powerful and An-Isotropic Hard ferrite Magnets /high intensity Rare Earth Nd-Fe-B Magnets and operate without the need for power supplies. The magnet system is available in two types: with Longitudinal polar field distribution for use with low levels of iron contamination and thin material layers, and with lateral polar field distribution for greater material thickness and larger iron particles.  

magnetic drum pulley, Designer Belts, pully legging

• Feature: Bored and Keyed Hubs, Maintenance Free.

Magnetic Head Pulleys is specially design for conveyor systems to continuously remove and discharge tramp metal from the product flow for purification and materials separation. These magnetic head pulleys is more preferable for superior removal of ferrous contamination such as spikes, nuts, nails, cans any many other unnecessary materials. Mostly used in wood, plastic, steel, paper, scrap yard, mining recycling, municipal recycling industries and many other recycling plants with best and maintenance free operation.

The magnetic Drum pulley replaces the drive pulley at the end of conveyor belts. In view of the wide variety of conveyor belt types, the drum pulley are supplied made to measure and ready for installation. As the figure clearly show, the magnetic head roller extracts the iron particles from the material flow and carries them to the underside of the belt where they are removed and collected. Head roller magnets for conveyor belt are supplied in permanent magnets. The version with permanent magnets are fitted with powerful and An-Isotropic Hard ferrite Magnets /high intensity Rare Earth Nd-Fe-B Magnets and operate without the need for power supplies. The magnet system is available in two types: with Longitudinal polar field distribution for use with low levels of iron contamination and thin material layers, and with lateral polar field distribution for greater material thickness and larger iron particles. 

Classifier, vibro screening machine, Vibro Screen Machine

magnetic drum pulleys, permanent magnetic equipments, Magnetic Plates

Magnetic Rod, magnetic bar, hand magnets, Grill Magnet, Earth Magnet

Power Magnetronics make magnetic drum pulley operates as head pulley on belt conveyors. It is specially designed for removing both large and small pieces of iron contaminants from product streams. It is powerful enough to remove tramp iron from heavy flows of bulk materials including bulk and abrasive material. These low cost, self-cleaning magnets remove tramp iron and purify materials conveyed in bulk forms. When Material carried on conveyor enters the magnetic field surrounding the magnetic drum pulley, pieces of ferrous metal in the material are attached to the belt. They are held magnetically against the belt until carried to the other side of the pulley, where the belts take them away from the magnetic field to be discharged. Non-magnetic material falls away from the pulley in normal operation. This cycle of separation is continuous and automatically working.