Plate Load Test Equipment Dealers in Kathwada, Ahmedabad

This apparatus is used to determine Softening point of Bitumen. It is that temperature at which a sample of bituminous material loaded by a 9.5mm dia steel ball, drops a specified distance when heated under specified conditions.

• Temperature Range: 0-400 deg °C.
• Model No.: ESCR- A
• Time totaliser range: 999.9 hours
• Accessories: Cutting die, nicking jig, bending cum transfer tool, specimen holder, test tube & rubber cork
• Water circulation: Through induction motor with stirrer
• Testing capacity: 6 tests at a time
• Heating load: 1.5 to 3 KW
• Body: Inner S.S and Outer M.S with powder coating
• Power Supply: 230V AC, 50Hz
• Inner size of bath: 12"X 8"X 9"
• Dimension: 28"X 13" X 25"
• Net weight: 36 kgs

Used to check and maintain the slope of the road as per design. Material- aluminum section of size 24 mm x 45 mm of thick gauge. Size- 3 meter, 3.5 meter, 3. 75 meter or as per requirement. Ratio- 2.0%, 2.5%, 3.0% or as per requirement. Accessories- highly sensitive magnetic spirit level and seat for it at centre.

• Application: Soil Testing
• Brand Name: DM
• Weight: 2 Kg
• Color: DA Gray
• Power: Electronic
• Body Material: Mild Steel
• Fall Frequency Of Soil Disc: 120 Beat/ min
• Usage: Determine the Moisture Content

Motorised Model: With consists of a brass cup held on an adjustable bracket. The bowl can be adjusted for a fall raised & dropped on a rubber of standard hardness by cam action. Complete with one casagrande-grooving tool, one ASTM grooving tools and a height gauge block. With counter. Fitted with a motor geared down to give approximately 120 RPM. Suitable for operation on 230 Volts, single phase, 50 cycles, A.C. supply. Relevant Standard: IS : 2720 (Part-V)    

Mett-Bio Metallurgical Testing & Services with its state of the art equipment setup consisting of Salt Spray Chamber Complying to the Requirement of ASTM B 117/ ASTM G 85.   Tests are performed in our ISO 17025:2005 NABL accredited lab under the standard Specified conditions or as per specific field conditions.   Salt spray testing is a test method where in a product or coatings resistance to corrosion is evaluated in severe corrosive conditions with extended exposure to a saline or salted spray   This testing is carried out in a closed chamber which is filled neutral salt fog. The test specimen is exposed to a predetermined time period and inspected during its exposure. This test is carried out to check the integrity of coatings, paints in a corrosive environment. This test is carried out as per ASTM B117.   Types of Salt spray testing:   · Neutral Salt Spray (NSS), · Acetic acid Salt Spray (ASS), · Copper sulphate Acetic Salt Spray (CASS)   The salt spray test can be acclimatized to suite different corrosivity level to simulate different environments.   The test specimen is exposed to a predetermined time period and inspected during its exposure. This test is carried out to check the integrity of coatings, paints in a corrosive environment. This test is carried out as per ASTM G 85.   A standard 5% salt solution of sodium chloride known as NSS or neutral salt spray and a solution of acetic acid known as ASS. The solutions are chosen based on the type of coating to be evaluated   Other salt variations: SO2 / Calcium Chloride (CaCl2)

• Ground Glass: 10mm thick and about 45 cm square or larger rough glass as per IS 2720 (Part V-1985) for mixing soil and water
• Spatula: Flexible with blade about 8 cm long and 2 cm wide made from stainless steel material as per IS:2720 (part V-1985)
• Evaporating dish: Made from porcelain material having diameter of about 12 to 15 cm with smooth surface as per IS 2720 (part V-1985)

The California bearing ratio test is penetration test meant for the evaluation of subgrade strength of roads and pavements. The results obtained by these tests are used with the empirical curves to determine the thickness of pavement and its component layers. This is the most widely used method for the design of flexible pavement. The laboratory method for the determination of C.B.R. of undisturbed and remolded compacted soil specimens, both in soaked as well as unsoaked state.

• Dimensions: Cm.
• Bottom diameter Top diameter Height: 20 10 30

Introduction The oldest, most widely used test for determining workability. This test is used to determine the workability of fresh concrete, which would normally be undertaken at the point of delivery to ensure the concrete, is of adequate consistency for placement. The test is applicable to concrete of medium workability.     The device is a hollow cone-shaped mould. The mold is filled in three layers of each volume. Each layer is rodded with a 16mm steel rod 25 times. The mould is then lifted away and the change in the height of the concrete is measured against the mould. The slump test is a measure of the resistance of concrete to flow under it own weight.   General Descriptions & Specifications The apparatus comprise of a slump cone with handles made of mild steel sheet, a chrome plated steel tamping rod of 16 mm diameter X 600 mm long, rounded off at one end, with a scale marked on it and a steel base plate with a carrying handle.     The mould for the test specimen will be in the form of frustum of a cone having the following internal dimensions as follows   The Cone is constructed of metal of at least 1.6 mm thickness and the top and bottom are open and at right angles to the axis of the cone. The mould have a smooth internal surface and provided with suitable foot pieces to a base plate and also handles to facilitate lifting it from the moulded concrete test specimen in a vertical direction as required by the test. The base plate is provided with cleats & swivel handle.   Optional Accessories CONCRETE SCOOP.FUNNEL FOR POURING CONCRETE IN CONE STRAIGHT EDGE

ESCR Test Apparatus: Environmental stress cracking is a property that is highly dependent upon the nature and level of stress applied and on the thermal history of specimen. This taste is normally employed for routine inspection purpose.   

• Type: Laboratory Furniture
• Material: Mild Steel
• Voltage: 220/230 Volts AC Supply

Fabricated out of thick Mild Steel Sheet these are designed so as to throw out toxic/harmful vapours, thus protecting costly instruments & the person working in the lab. The outer surface is finished with powder coated & inner surface is epoxy painted.   The working table top is fitted with acid/alkali resistant tiles/S.S & a small wash basin with connections provided for inlet & outlet of water. The front door moves vertically up & down with concealed counterbalanced weight. The unit is fitted with fluorescent light & a gas cock of gas/air supply. The space under the work station can be provided with storage compartments for storage purpose. The front-facing panel is fitted with 15/5 amp socket with switches for exhaust system & fluorescent light to work on 220/230 volts AC Supply.

Soil Testing Equipment, Bursting Strength Tester, Digital Comparators

Bulk density, Carbon Black content tester

bitumen testing equipment, civil laboratory equipment