Repair Sleeve Dealers

• Features: Provides excellent corrosion protection,UV and weather resistance makes it also ideal for LV cable joint outer protection.

HRSL is a heat shrinkable wrap around sleeve that is used for repairing damaged cable over sheaths on various types of cables.Provides excellent corrosion protection,UV and weather resistance makes it also ideal for LV cable joint outer protection.

The word “hernia” is derived from the Latin word for “rupture”. It is defined as an abnormal protrusion of an organ through a defect in its surrounding walls. It typically occurs due to weakness in the wall.Umbilical hernia occurs due to a weakness in the abdominal wall in the region of the navel. Umbilical hernias are seen in infants and toddlers as well as in adults.

Half repair Pipe Sleeve » General Half Repair pipe Sleeves are designed to avoid a costly shut down. Existing lines can be cased without thru-put loss, because it is not necessary to shut down the carrier line to perform the required repair. A full scope of sizes, ASTM grades of steel plate (structural and pressure vessel quality), wall thickness and longitudinal edge options are available. Half Sole Repair Sleeves, also called split casing or half wrap, are custom-fabricated to your specifications, to assure a precision product and secure fit. There are four types of material available, two pressure-rated steels and two structural-grade steel. The pressure-rated steel sleeves can be used to repair leaking and non-leaking defects while the structural-grade steel sleeves can function as reinforcement for a defective area. » Material Material used are structural quality carbon steel or pressure vessel quality carbon steel plates, which are to ASTM specifications, and in the following grades:API 5L Gr B, X42, X46, X52, X56, X 60, X 65, X70 - PSL 1 - PSL2 (minimum yield 245000 / 52000 / 60000 / 65000 / 70000)ASTM A36 (structural; minimum yield 36,000 psi)ASTM A572 GR42, GR50, GR55, GR60, GR65 (structural; minimum yield 29,000 psi)ASTM A516 GR55, GR60, GR65, GR70 (pressure vessel; minimum yield 38,000 psi)ASTM A537 Class I, Class 2, Class 3 (pressure vessel; minimum yield 50,000 psi) EN 10025 - S235, S275, S355, S450The chemical composition does not exceed the percentages specified for the ASTM material ordered. Repair sleeves are fabricated from plate with low carbon equivalency for good weld ability.The maximum allowable carbon equivalency (CE) quality carbon steel plates will be based on the heat analysis.The maximum allowable carbon equivalency (CE) pressure vessel quality carbon steel plates will be based on the heat analysis, in most cases. Note : The sleeve can be manufactured in any grade as per the application & client requirements. » Manufacturing Half Repair Pipe Sleeve is formed by rolling, step braking, or die forming without the use of heat treating.Longitudinal edges of the Half Sole are beveled for welding, if requested, at 30º. The bevel are a mechanical type and/or produced by plasma torch burning.Half Repair Pipe Sleeve ends have sheared square edges for fillet welding, unless square end bevel is requested, and are available in maximum lengths as per clients requirements. » Feature The steel repair sleeves can be used for internal and external corrosion, gouges, dents, grooves, arc burns, cracks, defective girth welds, laminations and leaks.Pressure containing sleeves feature a wall thickness equal to or greater than required for the maximum allowable operating pressure or the full strength of the pipe being repaired. The steel Repair sleeve material is certified and the carbon equivalent will not exceed 0.45 percent. Each half-sole segment comes with one pre-crimped back-up strip.Steel Repair Sleeves can be used as pads or cradles for above ground piping, drain tile supports and patches (segments in 90° and 180° arcs, from 6-inches to 10 feet in length are available as specials).Each Steel Repair Sleeve has standard bevels with a back-up strip and material certifications. Sleeve ends are square cut. Back-up strip are not included with Standard Girth Weld Steel Repair Sleeves but are available as special order. » Milling of Half Repair Pipe Sleeves for backing Strips Half repair pipe sleeves can be milled on the inside longitudinal edges for the backing strips. Depth of 1/16" (.625) -0" + 1/32" and width 5/8" (.625) -0 + 1/16" on each side. Outside longitudinal edges are beveled 30° (+5° - 0°) for welding. » Backing Strips Backing Strips are hot rolled commercial carbon steel sheet and strips of commercial quality. A-569 / A1011 SS GR33 / IS:2062 or equivalent in coils and cut lengths having a maximum carbon of 0.15%. 1 1/4" wide, 16 gauge (.0598) with a tolerance of min. 0.0538 - max 0.0658, 10' long, precrimped (10 degree total bend).   ASTM steel composition of A569/A1011 SS GR33/IS:2062: Carbon (Max) Manganese (Max) Phosphorus (Max) Sulphur (Max) Copper (when specified) 0.15 0.60 0.036 0.035 0.20 min.   » Mechanical Properties and Testing Mill test reports will be furnished on all materials. If stock plate is not available with a maximum hardness guarantee independent testing may be performed to check the hardness on stock plate and this report will be submitted along with ptoduct. If required additional testing reports will be furnished which includes destructive, magnetic particle, liquid penetrate, ultrasonic and radiographic reportrs carried out by a reputed third party. » Dimensional Requirements Longitudinal edges to be beveled to 30 degrees (+5 degrees -0 degrees), with a root face (land of 1/16" (+-1/32"). Inside diameter (I.D.) of each Half pipe repair sleeve will be fabricated to match the outside diameter (O.D.) of Standard nominal line pipe (bare with tolerance of: Half repair sleeves can be manufactures in such a way that when two (2) halves of the sleeve are placed on the pipe, their total circumference shall equal the circumference of the pipe minus a gap between the longitudinal edges on either side of 1/16" (-1/16" + 1/32") for welding. » Size We can manufacture in any size and also as per client's requirement.

Over time, conductors get damaged and need minor repairs. Compression Type Repair Sleeves, which are essentially two identical aluminium pieces fitted into each other, are used to repair them.

Heat Shrink Cable Repair Sleeves is manufactured from High Quality Cross-linked polyolefin material. Heat Shrink Cable Repairing Sleeve is an adhesive lined, wraparound heat shrink that can be easily applied without the need for disconnection. It provides superior environmental sealing, rugged mechanical protection and high performance electrical insulation.Provides permanent waterproof barrier & environmental seal.

Heat-shrinkable wraparound sleeves are a fast, versatile and permanent method of repair for damaged cable outer sheaths. Upon application of heat, the sleeve shrinks and adhesive melts and bonds to the cable sheath, creating a permanent seal against moisture entry into the cable. Wraparound sleeves are useful for repairs to cable outer sheath where it is not possible to use tubular sleeves.

repair sleeves, Insulator Hardwares, Suspension, substation connectors

Transmission Repair Sleeve, AGS Clamp, Socket Clevis, yoke plate

repair sleeves, lt overhead electrical transmission line materials

Repair sleeve, Crank Shaft, Hot Rolled Bars, Chemical pump shaft

Repair sleeve, plastic shaft, rocker shafts, step shaft, half shaft

Repair sleeve, Samsung Mobile Battery, camera phone

Yamuna Steel Repair Sleeves can be used for internal and external corrosion , dents, grooves arc burns, cracks, defective girth welds, laminations and leaks.

Repair sleeve, mobile screen, Mobile Memory Cards, Mobile Phone Parts

Earth Wire Repair Sleeves, Midspan Compression Joint, Cleat Clamps

Repair sleeve, compression dead end clamp, f clamp, AAAC Coyote Conductor

Repair sleeve, Ball Hook

Cable Repair Sleeves, Link Boxes, Cable Wire, ht cable