Rubber Valves Dealers in Ahmedabad

• Country of Origin: India
• Material: Stainless Steel
• Certification: ISO 9001:2008 Certified
• Color: Grey, Grey-silver, Shiny-silver, Silver
• Type: Butterfly Valves
• Condition: New
• Driving Mode: Gear
• Media: Air, Gas, Water
• Specialities: Investment Casting
• Size: 40MM TO 900MM

Motorized Rubber Lined Butterfly Valves that we provide in the markets are widely acknowledged by the clients spread all across the globe. Motorized Rubber Lined Butterfly Valves are extensively used for HVAS & utilities. Minimal maintenance, trouble free functioning, compact design and light weight are some of the unique features of Motorized Rubber Lined Butterfly Valves we manufacture. About Motorized Rubber Lined Butterfly Valves : Made available in an integrally moulded version Body lines functions as the soft seat Provides bi-directional sealing against vacuum upto the pressure of PN 10/PN 16   Electrical Actuator Details   Manufacturer Cair Euromatic Automation Brand / Model Cair / MOD Characteristic On - Off Type Travel 90 Degree Indicator Continuous Position Indicator Phase Single Phase Power Supply 220V AC, 50 Hz Body Material Aluminum Alloy Ambient Temperature 20oC ~ 80oC Motor Insulation Class F Protection Class IP - 67 Weather Proof Manual Adjustment Wrench Setting Limit Switch 1NO + 1NC output of 220V AC Position Power Failure Stay Put Manual Override Provided   Accessories   Modulating Controller 4 ~ 20 mA (Available on request) Potentiometer Feedback Available on request Integral Starter unit Available on request Control Panel Available on request Size Range : 1.1/2" To 72" Technical Specifications   Body Cl (IS 210 Gr. FG 200 / 220) / WCB Disc CF8 / CF8M /CF3M/S.G.Iron/ Teflon Coated/ Power Coated / Naylon Coated Seat EPDM / Nitrile/ Naylon / Hayplon / Viton Shaft AISI 410 Valve Type Centric Disc Butterfly Valve with a Single Piece Rubber Lined Body Body Type Short Wafer (Sandwiched Between Flanges) Seat Type Integrally Moulded with the Body End Connection Wafer Sandwiched (Lug Type On Request) Pressure rating PN 10 /PN 16 (On Request) Oper. Temp, range -25oC to 130oC (Depending on MOC) Protection Class Tight Shut Off Operation Hand Lever for Sizes from 40 NB to 300 NBWorm Gear Boxes for 200 NB to 500 NB Key Features : Integrally moulded seat liner on the body, which ensures excellent dimensional stability & guaranteed seat tightness. Seat liner extending on to the contact faces ensures perfect sealing and eliminates the need for separate flange gaskets. Narrow land disc ensures perfect sealing with least operating torque requirements. A fully universal body design ensures fitting of the valve between companion flanges of all popular standards (viz : ANSI, BS, DIN, JIS, IS etc.) The notch disc & band lever ensures locking of the valve in 8 intermediate position in addition to close and open position. Hand lever can be locked through pad lock. Body castings made of superior FG 260 grade cast iron to ensure additional strength. Valve disc made of stainless steel / ductile cast iron which enable protection against possible water hammer or pressure surges. A truly line size body bone to ensure maximum flow capacity with the lowest pressure drop.   Standards   Design and Manufacturing API 609 category A/BS 5155 / MSS SP-67 / C-504 Valve Face to Face Dimensions Short wafer as per ISO 5752 Tab 5 / API 609 Category A Top Flange Drilling ISO 5211 Part II Inspection and Testing API 598 / BS 6755 Flange Standard Conformity ANSI150, DINPN6/10.JIS5K/ 10KBS10TabD&E, IS 6392 NP 0.6/1.0 Size Range : 1.1/2" to 72" Flanged

• Weight: 5Kg
• Packaging Type: Wooden Box
• Valve Size: 1inch
• Voltage Range: 24 V AC
• Brand Name: SRK
• Material: Stainless Steel
• Color: White
• Structure: U Section
• Diameter (mm): 40 Mm, 50mm
• Overall Length: 6-10 Inch
• Specialities: Non Breakable, Investment Casting, Heat Resistance, Casting Approved
• Diametre (milimetre): 100 To 1000 Mm
• Type: Industrial Valves
• Condition: New
• Finishing: Coated
• Automatic Grade: Manual
• Warranty: 1 Year
• Actuation Type: Single Acting

• Country of Origin: India
• Material: Cast Iron
• Certification: ISI Certified
• Application: WATER, AIR, INDUSTRIAL
• Color: Blue
• Feature: Corrosion Proof
• Size: 1" TO 3"

Pinch valves, offered by our company, are the modified version of laboratory pinchcock in which rubber sleeve is protected under the casting made of cast iron. The main advantage of Pneumatic Pinch Valves is that the fluid passing from it does not come in contact with its metal parts except the sleeve. This property makes it corrosion resistive against the action of various fluids. Open Body Pinch Valves assure the smooth flow of water like pipeline and their collar sleeve eliminates gasket. Pinch valve is user friendly and can be operated easily as compared to other wheel operated valves. This valve allows positive control over flowing media because of its in between stoppage that gives desired throttling. These pinch valves are extensively used for handling corrosive slurry, liquid with solid suspensions, abrasive media, and many others. We offer pinch valve in best application range with flange as per BS, DIN, ASA & IS dimensions, and ranging between 15mm to 300mm. We are known widely as one of the proficient Pinch Valves Exporters and Suppliers. General Features & Highlights Seat Less & Glandless ValvesField Replicable Elastomer Sleeve.Elastomer Sleeve Having Four Reinforced LugsFlanged Ends & Drilled to Din, Ansi, Bs-10, Is, Etc.this Valve Incorporates allthe Design Modifications Based On Our Experience & is of Study Construction to Handle Abrasive Corrosive Media. BRIEF DETAILS OF PINCH VALVE Pinch Valve is a Seat less & Glandless valve.Pinch valve is a modified version of laboratory pinchcock. A rubber sleeve is protected under a cast iron casting.The fluid passing through do not come in contact with either body covering or any other metal parts of the valve except the sleeve.Hence the body and other metal parts are almost permanently not subjected to the corrosive action of the fluid.The flow through the valve is straight and full as that of a pipeline, when the valve is fully open. Further, the collar of the sleeve eliminates gasket.The valve is simple hand wheel operated of rising wheel type. Therefore the operation of the valve is just simple as other wheel operated valve.The in-between stoppage will allow the desired throttling. Thus the valve offers positive control over flowing media. Applications Pinch valve finds its best application in handling corrosive slurry, abrasive media, liquid with solid suspensions and many others, which are difficult to handle with seat valve. Range The flange of the pinch valve can be supplied in accordance to BS, DIN, ASA & IS dimensions The range for the valve is from 15 mm TO 300 mm. Actuation The valve can be supplied with Electrical and pneumatic actuation. Operating Manual OF PINCH VALVE THE PINCH VALVE is a modified version of the laboratory pinchcock. A rubber sleeve is protected under a Cast iron or Aluminum split body casting. The valve is a simple hand wheel operated of rising wheel type. The operation of the valve is same as other hand wheel operated valve, it closes when moved in clockwise direction and opens when moved in anticlockwise direction. The in-between stoppage will allow the desired throttling. Thus the valve offers positive control over flowing media. The flow through the valve is same as that of a pipeline, when the valve is in fully opened condition. Further, the rubber sleeve eliminates the need of a gasket. PRELIMINARY PRECAUTION On receipt of the valve please check the position of the valve, as it is advisable to keep the valve in fully opened condition. Also check the position of the travel limit nut, if found loose then tighten the set screw of the nut. INSTALLATION The valve can be installed without any gasket unless it is required for some specific purpose. Tighten the nut of the flanges evenly & equally, but avoid too much tightening. After installation check the free movement of the upper & lower pinching bar by opening & closing the valve. The valve is then ready for the service it is installed for. MAINTENANCE If the valve is found leaking through the seat after sometime even though in fully closed condition, then set the travel limit nut by just taking it 1 or 2 threads above & then tighten. This will allow more room for traveling of rubber sleeve & ensure the valve to zero leakage. This problem sometimes occurs when the sleeve is slightly worn out, when used under abrasive condition. Further, The Rubber sleeve of the valve up to 2” (50mm) have a single lug on either side and it goes into the hollow passage of the pinching bar where it is fixed with the lug clamping screws. In the higher sizes above 2” the sleeves have two lugs on either sides and is fitted overlapping the pinching bar. DISMANTLING THE VALVE & REPLACING THE RUBBER SLEEVE When the rubber sleeve is ruptured or totally worn out then it is to be replaced with a new one. In this case first dismantle the valve by following the instructions. Remove the hand wheel.Open the Tie Bar nuts.Disconnect the spindle from the Horseshoe connection and remove it completely with the bridge.REMEMBER not to temper the set screw of the yoke bush, unless if required it should be completely tight.Open out the nuts & bolts of the split body of the valve.Remove the screw of the lugs from both the pinching bars.Now fit the new rubber sleeve & reverse the operation to assemble the complete valve. NOTE It is advisable to keep a spare rubber sleeve for maintenance purpose, considering the self life of the Rubber as six months when packed & stored in dark. The Pinch valves should be stored in fully open condition only. We also offer complete spares of the valves, but request you to place your order a week in

• Size: 1” NB to 12” NB (ANSI B 16.5, 125# FF)
• Design Standard: BS 5152 / ANSI B 16.34
• Hydro Testing: Body : 10 Kg/Cm² & Seat: 06 Kg/Cm²
• Rubber Lining Thk: Min. 3mm up to 6” NB & above 6” NB Min. 4mm

• Size: 15mm to 50mm
• Media: Water /Oil / Steam / Air /Gas
• Body: Cast Iron/ Cast Steel
• Bonnet: Cast Iron
• Wheel: Cast Iron
• Diaphragm: Epdm / Ebonite Rubber
• Operation: Hand Wheel Operated
• Hyd Test Pressure: 10 Bar
• Seat Test Pressure: 85PSIG, (6KG CM2 )
• Temperature: 85 Degree C
• Ends Connection: Flange End Table D /150# ( ANSI B 16.5 )

• Brand Name: Videocon
• Material: Rubber
• Shape: Round
• Used in: Washing Machine
• Durability: Long Life
• Performance: Optimum

• Valve Size: Customised
• Brand Name: GURUKRUPA ENGINEERS
• Media: Air, Water, Gas, Fuel

Rubber check valves It is available with standard as well as customized configuration. The size ranges from 50 NB to 900 NB. Range also includes pressure rating from 150 # to 600 #.

We are an incomparable name in offering a superior quality Rubber Lined Butterfly Valve that ensures an unrestrained flow of the liquid. The offered butterfly valve is manufactured utilizing optimum quality raw material and lined with optimum grade rubber that assures its high sealing capacity. Furthermore, the offered butterfly valve is meticulously checked on various quality parameters by quality controllers to render a flawless supply at clients’ end. Features: Minimum bearing friction torque. Precise design Damage-resistance

With our recognized reputation in the current market for qualitative production, we are devotedly engaged in manufacturing and supplying quality Rubber Lining in Valves and Flappers. In order to deliver defect-free range at clients end, it is thoroughly examined on various parameters by our quality controllers. It is manufactured using premium quality components procured from certified vendors, and contemporary techniques as per the international quality standards. Moreover, it is made available in different technical specifications as per the needs laid down by our clients. Features: Sturdy design Highly durable Perfect finish

BHAVYA Fluid Controls Rubber Lined Butterfly Valve has Slim-Seal design, maintenance free shutoff. Lug Type Body Center Disc Butterfly Valves by BHAVYA Fluid Controls are high performance solutions to your industrial Butterfly Valve needs. For abrasive and corrosive applications we supply valves with PTFE lining and composite construction butterfly valves which combine light weight with good chemical resistance with a 10 bar pressure rating. Rubber encapsulated disc butterfly valve also available for acidic application. BHAYA Fluid Control Rubber Lined Butterfly Valves are fitted with a liner that is heat bonded to the valve body. Rubber Lined Butterfly Valves are also familiar by the name of Bonded Seat Butterfly Valve. This prevents movement of the liner inside body during pressure and offers exceptional reliability for Control or On/Off valves with Zero Leakage (Class VI)   DN50-DN4500, PN6/10/16 Flange Dimension DIN2501/ANSI B 16.5/ANSI B 16.47/JIS/IS Design - BS 5155 or API609 Final inspection tests to BS 6755 / API598 Operation – Flow Control Lever / Gear / Actuato

Wafer Rubber Sleeved Butterfly Valves Pressure Rating PN. 10 & PN. 16Multipurpose Wafer Designed Rubber Sleeved Butterfly Valves100% Tight Shut-OffOne Piece Body With Centered Disk.Uniflow Direction Installation.

Chemical Pinch Rubber Valve, Water Cool Condenser, Wirtgen Track Pad

Rubber Wedge Gate Valve, Butterfly Valves, Butterfly Control Valves

Replaceable Rubber Sleeve Valve, stainless steel sight glass

rubber valves, rubber valves, dry magnetic seperation machine

Diaphragm, Rubber Conveyor Pulley, Rubber Products, Rubber Diaphragm