Steel Valves Dealers in Kathwada, Ahmedabad

• Brand Name: SYSCHEM
• Pressure: Up to 600
• Size: Up to 2 Inch
• FEATURES: Intergral or Welded Flanges,Two piece self aligning packing gland,Captured Graphite Spiral wound gasket
• Material Grade : A 105/ LF2/ F 304/ F316/ F11/ F22/ F55
• Usage/Application: Chemical, Oil & Gas
• Valve Size: Up to 2 Inch
• Media: Chemical, Oil & Gas
• End Connection: Flanged
• Design Type: Piston Type
• I Deal In: New Only

• Material: Stainless Steel
• Application: WATER,INDUSTRIAL,GAS
• Country of Origin: Made In India
• Brand Name: K-TECH
• Connector Type: SCREWED, FLANGE EDND, THREADED
• Size: 1/4
• Number of Ways: 3 Way
• Pressure: High Pressure
• Power: NO
• Finish Type: MIRROR
• Warranty: 1 YEAR
• I Deal In: New and Second Hand

• Material: Forged Steel
• Application: Water Fitting
• Feature: Blow-Out-Proof, Casting Approved
• Structure: Double Half Shaft
• Port Size: 0.1mm-5cm
• Number Of Way: 2way, 3way, 4way
• Size: 1/4″ To 2″ INCH
• Pressure: High, Low, Medium
• Technics: Gear Operated

• Media: Water, Gas, Air
• Wog Rating: 150, 300, 600
• Size: 15 to 200 mm
• Material: Stainless Steel, Carbon Steel
• Pressure: Medium
• Temperature: +30°C
• Finish: Polished

Reckoned for our extensive array of products, we efficiently serve our customers from Ahmedabad(India). In order to deliver flawless range of products, we keep stern check on the product development, storage, packaging and delivery.

Our FLOEC Duplex Steel Non Return Valves are applied in different chemical industries to combine different gases into single gas stream. These valves offer trouble-free installation while requiring least maintenance.

Forged Stainless Steel Valves compact design GateGlobeNon-Return Valves are manufactured in a wide-ranging materials like Forged Carbon Steel in compliance to A105, Forged Alloy Steel like LF2, F11, F22; F51 and Forged Stainless Steel like F304, F304L, F316 and F-316L. The sizes available are from 10NB through 50NB and pressure rating from ASME 800# through 2500#.

• Application: Industrial
• Material: CS;SS;ALLOYS
• Brand Name: FLOWJET
• Application: Industrial
• Material: CS;SS;ALLOYS
• Connection Type: FLANGED / SCREWED/SW
• Material Grade: 304, 316, 410, DUPLEX, SUPER DUPLEX
• End Connection Type: Flanged

We are the leading supplier of this products.

• Material: Cast Steel
• Voltage Range: 24 V AC
• Automatic Grade: Automatic
• Overall Length: 6-10 Inch
• Number Of Way: 2way
• Usage: Water Fitting
• Specialities: Investment Casting, Heat Resistance, Durable

We offer forged steel ball valve. Jupiter controls in haryana , jupiter controls ball valve in haryana, cast iron ball valve manufacturer, cast carbon steel ball valve manufacturers,cast stainless steel ball valve exporter, forged steel ball valve supplier,single piece design ball valve stockiest, two piece design ball valve manufacturer,three piece design ball valve manufacturers, high pressure ball valve exporter,two way ball valve supplier, three way ball valve stockiest, four way ball valve manufacturer,high performance ball valve manufacturer, jacketed ball valve manufacturersflush bottom ball valve exporter, gear operated ball valve supplier, pneumatic ball valve stockiest, i.c. Ball valve (investment casting) stockiest, multiport ball valve manufacturers, mixing & diverting type ball valve exporter, fire safe design ball valve supplier, zero leakage ball valve stockiest, ball valve in punjab, ball valve manufacturer in haryana,cast iron ball valve, cast carbon steel ball valve, cast stainless steel ball valve, forged steel ball valvesingle piece design ball valve, two piece design ball valve, three piece design ball valve, high pressure ball valve, two way ball valve, three way ball valve, four way ball valve, high performance ball valve, jacketed ball valve, flush bottom ball valve, gear operated ball valve, pneumatic ball valve, i.c. Ball valve (investment casting), multiport ball valve, mixing & diverting type ball valve, fire safe design ball valve, zero leakage ball valve

• Brand Name: MEGA VALVES
• Material: Stainless Steel, Alloy Steel, Carbon Steel,HANDWHEEL OPERATED GATE VALVE FLANGED 150#
• Color: Sky Blue, ELECTRO PLATING
• Condition: New
• Pressure: Medium
• Application: Gas Fitting, Oil Fitting, Water Fitting
• Certification: ISI Certified
• Feature: Casting Approved, Good Quality, Investment Casting
• Weight: 10-15kg
• Country of Origin: India
• End Connection: Flanged
• Temperature Of Media: UP TO 180 D
•  Type: CARBON STEEL GATE VALVE

• Size: 100-150mm
• Certification: ISI Certified
• Application: Gas Fitting, Oil Fitting
• Weight: 10-20kg
• Feature: Casting Approved, Corrosion Proof, Good Quality
• Pressure: High, Medium
• End Connection: Butt Weld, Flanged
• Material: Stainless Steel

Pinch valves, offered by our company, are the modified version of laboratory pinchcock in which rubber sleeve is protected under the casting made of cast iron. The main advantage of Pneumatic Pinch Valves is that the fluid passing from it does not come in contact with its metal parts except the sleeve. This property makes it corrosion resistive against the action of various fluids. Open Body Pinch Valves assure the smooth flow of water like pipeline and their collar sleeve eliminates gasket. Pinch valve is user friendly and can be operated easily as compared to other wheel operated valves. This valve allows positive control over flowing media because of its in between stoppage that gives desired throttling. These pinch valves are extensively used for handling corrosive slurry, liquid with solid suspensions, abrasive media, and many others. We offer pinch valve in best application range with flange as per BS, DIN, ASA & IS dimensions, and ranging between 15mm to 300mm. We are known widely as one of the proficient Pinch Valves Exporters and Suppliers. General Features & Highlights Seat Less & Glandless Valves Field Replicable Elastomer Sleeve. Elastomer Sleeve Having Four Reinforced Lugs Flanged Ends & Drilled to Din, Ansi, Bs-10, Is, Etc. this Valve Incorporates all the Design Modifications Based On Our Experience & is of Study Construction to Handle Abrasive Corrosive Media. BRIEF DETAILS OF PINCH VALVE Pinch Valve is a Seat less & Glandless valve. Pinch valve is a modified version of laboratory pinchcock. A rubber sleeve is protected under a cast iron casting. The fluid passing through do not come in contact with either body covering or any other metal parts of the valve except the sleeve. Hence the body and other metal parts are almost permanently not subjected to the corrosive action of the fluid. The flow through the valve is straight and full as that of a pipeline, when the valve is fully open. Further, the collar of the sleeve eliminates gasket. The valve is simple hand wheel operated of rising wheel type. Therefore the operation of the valve is just simple as other wheel operated valve. The in-between stoppage will allow the desired throttling. Thus the valve offers positive control over flowing media.   Applications Pinch valve finds its best application in handling corrosive slurry, abrasive media, liquid with solid suspensions and many others, which are difficult to handle with seat valve. Range The flange of the pinch valve can be supplied in accordance to BS, DIN, ASA & IS dimensions The range for the valve is from 15 mm TO 300 mm. Actuation The valve can be supplied with Electrical and pneumatic actuation. <? include("other-files/pinch-valve.html"); ?>       Operating Manual OF PINCH VALVE THE PINCH VALVE is a modified version of the laboratory pinchcock. A rubber sleeve is protected under a Cast iron or Aluminum split body casting. The valve is a simple hand wheel operated of rising wheel type. The operation of the valve is same as other hand wheel operated valve, it closes when moved in clockwise direction and opens when moved in anticlockwise direction. The in-between stoppage will allow the desired throttling. Thus the valve offers positive control over flowing media. The flow through the valve is same as that of a pipeline, when the valve is in fully opened condition. Further, the rubber sleeve eliminates the need of a gasket. PRELIMINARY PRECAUTION On receipt of the valve please check the position of the valve, as it is advisable to keep the valve in fully opened condition. Also check the position of the travel limit nut, if found loose then tighten the set screw of the nut. INSTALLATION The valve can be installed without any gasket unless it is required for some specific purpose. Tighten the nut of the flanges evenly & equally, but avoid too much tightening. After installation check the free movement of the upper & lower pinching bar by opening & closing the valve. The valve is then ready for the service it is installed for. MAINTENANCE If the valve is found leaking through the seat after sometime even though in fully closed condition, then set the travel limit nut by just taking it 1 or 2 threads above & then tighten. This will allow more room for traveling of rubber sleeve & ensure the valve to zero leakage. This problem sometimes occurs when the sleeve is slightly worn out, when used under abrasive condition. Further, The Rubber sleeve of the valve up to 2 (50mm) have a single lug on either side and it goes into the hollow passage of the pinching bar where it is fixed with the lug clamping screws. In the higher sizes above 2 the sleeves have two lugs on either sides and is fitted overlapping the pinching bar. DISMANTLING THE VALVE & REPLACING THE RUBBER SLEEVE When the rubber sleeve is ruptured or totally worn out then it is to be replaced with a new one. In this case first dismantle the valve by following the instructions. Remove the hand wheel. Open the Tie Bar nuts. Disconnect the spindle from the Horseshoe connection and remove it completely with the bridge. REMEMBER not to temper the set screw of the yoke bush, unless if required it should be completely tight. Open out the nuts & bolts of the split body of the valve. Remove the screw of the lugs from both the pinching bars. Now fit the new rubber sleeve & reverse the operation to assemble the complete valve.   NOTE It is advisable to keep a spare rubber sleeve for maintenance purpose, considering the self life of the Rubber as six months when packed & stored in dark. The Pinch valves should be stored in fully open condition only. We also offer complete spares of the valves, but request you to place your order a week in For more details please click on the links given below

• Brand Name: Allines
• Condition: New, Good
• Place of Origin: Place of Origin
• Packaging: Bulk
• Product Type: Forged Steel Valve

As a known name, we ensure safe and timely delivery of the orders at any desired Ahmedabad(India). We make sure the ranges of product we offer purchasers with are as per global quality management standards.

• Minimum Order Quantity: As per Customer Needs

We are offering forged steel gate valves,globe valves,chake valves moc :- a105,f304,f316,lf2 size :- to 2” pressure :- up to 2500 class end conection :- s/e & f/e.

Forged steel globe valve, All Globe Valve stem is made from solid one piece construction. The yoke bush of Globe Valve has a long thread engagement for accurate stem alignment.Body & Bonnet made from high quality forging. The Forgings are precision machined for high performance, Leak Proof Body-Bonnet Joint With Spiral Wound Gasket, Die moulded Graphite (Grafoil) Packing Rings, controlled clearance between stem, gland and bonnet bushing for guaranteed low emissions and also suitable for higher temperature.

• Pressure: 25 Kg/cm² in working condition

Cast steel globe valve Applications : Water, Steam, Oil & Gas, Acid & Chemicals, Temperature : 200° Centigrade in Working Condition, Guarantee : 15 months replacement guarantee.

We are the leading exporter and supplier of this products.

DESIGN & TESTING INTERNATIONAL STANDARD: Valve Design                           : BS 5352 Pressure Testing                     : BS 5146 Face To Face                         : ANSI B 16.10 Butt Weld End                         : ANSI B 16.25 Socket Weld End                    : ANSI B 16.11 Screwed End                         : ANSI B 1.20.1(BSP/NPT)   SALIENT FEATURES: Body & Bonnet made from high quality forging. The Forgings are precision machined for high performance Leak Proof Body-Bonnet Joint With Spiral Wound Gasket Rising Stem & Rising Hand Wheel Construction. Ground Finish Stem Self Aligning Two Piece Gland Die moulded Graphite (Grafoil) Packing Rings, controlled clearance between stem, gland and bonnet bushing for guaranteed low emissions and also suitable for higher temperature. Precision Stem Packing Chamber Deep stuffing box is providing for tightness and maximum long packing life. Swinging Eye Bolts facilitate easy access to the stuffing box. Back seating feature facilitates repacking of the stuffing box on line with the valve in fully open position. Stellited Disc, Seat Ring & Back Seat can also be offered on special request.

We ar one of the leading manufaturer , exporter and supplier of Stainless Steel Vaccum Valve Screwed. Our headquarter based in Ahemdabad Gujarat.We offers a rigid stainless steel valve plug to seal off the outlet orifice. The valve plug is protected from a rush of air by a stainless steel baffle. The baffle provides a rigid support for the float guide bushing while allowing the float rod enough clearance for self seating operation

• Brand Name: HYPER
• Material: As per application
• Valve Size: 1/2
• Media: Air, Water, Gas, Fuel
• Cap Type: Screwed
• Size: 1/2 inch x1/2 inch to 2 inch x 2 inch
• Temp. Range: Max. 100 Deg. C
• Shape: Angle type
• Set Pressure: PN10, PN16
• Seat: Metal Seat / Soft Seat
• Over pressure: 10% of set pressure.
• Design: Full lift, Close Bonnet.
• Temperature Range: Up to 250 C
• Blowdown: Maximum 15% less then set pressure.

• Material: Stainless Steel
• Brand: PARTHIV
• Pressure: 20KG
• Connector Type: Flanged End
• Material Grade: SS 202/304/316
• Colour: SILVER
• End Connection Type: Flanged
• Working Temperature: 80 deg cel
• Size: 1/2inch to 8inch
• Features: Withstand considerable pressure, Good quality plastic

  Technical Data: Manufacturing Std : BS 5352 Face to Face, End to End : D N Bros. Std. End Connection : Screwed Ends to BSP/BSPT/NPT   : Socket Weld Ends to ANSI B16.11 Inspection and Testing Std : BS 6755 (Part-1)

Nivz Valves Forged Steel Gate Valves are Bolted Bonnet, outside screw and yoke type, rising spindle & non rising hand wheel construction. Nivz Forged Valves Body and bonnet made from high quality forgings. Nivz Valves & Automation manufacturer and exporter Forged Steel Gate Valves in size 1/2” (DN15) to 2” (DN50) to suit various critical, non-critical applications and pressure rating in 800 and 1500 class. Nivz make Forged Steel Gate Valve manufacturing range covers Regular Port and Standard Port both types of Valve. Regular Port gate valves have fast delivery or ready stock, for Standard Port gate valve do manufactuing on order basis. Nivz manufacture Forged Steel Gate Valve in wide range of Body Materials like ASTM A 105 - Forged Carbon Steel, ASTM A 182 F 304/304L/316/316L - Forged Stainless Steel 304/304L/316/316L, ASTM A 182 F 11/22 - Alloy Steel to suit high temperature and pressure industrial application. Forged Steel Gate Valves are available under any Third party inspection also. For High Pressure & Temperature application Stellited F6 Face Seat & Disc available. Forged Gate Valve available in Threaded End (BSP / NPT Female), Socket Weld End, Butt Weld End, Weld Neck End and Flanged End Connection. For flanged end connection Forged Steel Gate Valve flanges will be a fabricated / welded with a valve body, flanges are not integral forged with body. Wide range of Forged Steel Gate Valve Manufacturer, A 105, F11, F22, F304L, F316L Material Forged Valve Exporter, Stockist, Supplier, Importer. Application Power Plants & Process Industries Petrochemical Plants & Refineries Fertilizers Plants Cement & Steel Industries Process & General Industries Sugar Industries & Distillery Plants Water, Steam, Gas, Oil & other Non-aggressive media Other application on request Salient Features of Gate Valve Body & Bonnet made from high quality forging. The Forgings are precision machined for high performance Leak Proof Body-Bonnet Joint With Spiral Wound Gasket Ground Finish Stem Self Aligning Two Piece Gland Back seating feature facilitates repacking of the stuffing box on line with the valve in fully open position.

A prominent supplier of huge range of Forged Steel ball valve.

We offer high quality SS Needle Valve at very affordable market price. These needle valves are manufactured using very high quality raw material and very skillful workers. These can be tailor made according to the specification provided by the customers. These products are in great demand in critical environments such as petrochemical, fluid power, electronics, process machinery and other major industrial applications.