Steel Valves Dealers in Memco, Ahmedabad

J. D. Controls Forged Steel Gate Valves are Bolted Bonnet, outside screw and yoke type, Rising Spindle construction Body and bonnet made from high quality forgings. J. D. manufacturing Forged Steel Gate Valves in size 1/2 (DN15) to 2 (DN50) to suit various critical, non-critical applications and pressure rating up to 1500 class in Regular (Reduce) bore & Standard (Full bore) design. DESIGN & TESTING INTERNATIONAL STANDARD:  Valve Design                           : API 602 / BS 5352 Pressure Testing                     : API 598 / BS 5146 Face To Face                         : ANSI B 16.10 Butt Weld End                         : ANSI B 16.25 Socket Weld End                    : ANSI B 16.11 Screwed End                          : ANSI B 1.20.1(BSP/NPT)   SALIENT FEATURES: Body & Bonnet made from high quality forging. The Forgings are precision machined for high performance Leak Proof Body-Bonnet Joint With Spiral Wound Gasket Bi-Directional Shut-Off Ground Finish Stem Self Aligning Two Piece Gland Die moulded Graphite (Grafoil) Packing Rings, controlled clearance between stem, gland and bonnet bushing for guaranteed low emissions and also suitable for higher temperature. Deep stuffing box is providing for tightness and maximum long packing life. Swinging Eye Bolts facilitate easy access to the stuffing box. Back seating feature facilitates repacking of the stuffing box on line with the valve in fully open position. Stellited Wedge (Gate), Seat Ring & Back Seat can also be offered on special request.

We are the leading exporter and supplier of this products.

Forged steel valves, Industrial Forged Steel Globe Valve, Forged Steel Gate Valve, Forged Steel Check Valves & Forged Steel Ball Valve in Regular (Reduced) and Standard Bore (Full bore) with Screwed End, Socket Weld End & Butt Weld (Welded Neck) End Connection.J D Ball Valves are also available with different type of Seat, Seal & Packing material such as P.T.F.E. (Virgin) Glass Filled P.T.F.E. Carbon Filled P.T.F.E. Graphite (Grafoil) PEEK to suit special requirement of client.

• End Connection: Butt Weld
•  Type: Steel Gate Valves
• Condition: New
• Pressure: Low, Medium
• Feature: Blow-Out-Proof, Casting Approved
• Color: White
• Weight: 10-15kg, 15-20kg
• Application: Gas Fitting
• Material: Stainless Steel
• Brand Name: SRK
• Size: 100-150mm, 150-200mm
• Country of Origin: India

• End Connection: ASA 150
• Brand Name: Durga
• End Connection Type: Flanged
• Size: 1/2 inch to 6 inch
• Temp. Range: Upto 230 degree C
• Suitable For: Steam,Water,Oil,Air
• Air Test Sheet Weight: 7kg
• Material Grade: SS 304 / SS 316/ WCB

• Material: Stainless Steel
• Application: Gas Fitting, Oil Fitting, Water Fitting
• Weight: 10-15kg, 15-20kg, 20-25kg, 25-30kg
• Feature: Blow-Out-Proof, Casting Approved, Corrosion Proof, Durable, Good Quality, Investment Casting
• Structure: Double Half Shaft, Pinless, U Section
• Type: Stainless Steel Ball Valve
• Color: Grey, Silver
• Pressure: High, Low, Medium

• Country of Origin: India
• Material: Stainless Steel
• Feature: Good Quality
• Color: Silver
• Condition: New
• Automation Grade: Manual

• Brand Name: MEGA VALVES
• Material: Stainless Steel, Alloy Steel, Carbon Steel,HANDWHEEL OPERATED GATE VALVE FLANGED 150#
• Color: Sky Blue, ELECTRO PLATING
• Condition: New
• Pressure: Medium
• Application: Gas Fitting, Oil Fitting, Water Fitting
• Certification: ISI Certified
• Feature: Casting Approved, Good Quality, Investment Casting
• Weight: 10-15kg
• Country of Origin: India
• End Connection: Flanged
• Temperature Of Media: UP TO 180 D
•  Type: CARBON STEEL GATE VALVE

• Material: 316
• Feature: S.S Round Bar
• End Connection: Butt Weld, Flanged, Screwed, Socket Weld Ends
• Color: Silver
• Pressure: High Pressure
• Usage: Chemical, Water, Fire

• Size: 100-150mm
• Certification: ISI Certified
• Application: Gas Fitting, Oil Fitting
• Weight: 10-20kg
• Feature: Casting Approved, Corrosion Proof, Good Quality
• Pressure: High, Medium
• End Connection: Butt Weld, Flanged
• Material: Stainless Steel

Pinch valves, offered by our company, are the modified version of laboratory pinchcock in which rubber sleeve is protected under the casting made of cast iron. The main advantage of Pneumatic Pinch Valves is that the fluid passing from it does not come in contact with its metal parts except the sleeve. This property makes it corrosion resistive against the action of various fluids. Open Body Pinch Valves assure the smooth flow of water like pipeline and their collar sleeve eliminates gasket. Pinch valve is user friendly and can be operated easily as compared to other wheel operated valves. This valve allows positive control over flowing media because of its in between stoppage that gives desired throttling. These pinch valves are extensively used for handling corrosive slurry, liquid with solid suspensions, abrasive media, and many others. We offer pinch valve in best application range with flange as per BS, DIN, ASA & IS dimensions, and ranging between 15mm to 300mm. We are known widely as one of the proficient Pinch Valves Exporters and Suppliers. General Features & Highlights Seat Less & Glandless Valves Field Replicable Elastomer Sleeve. Elastomer Sleeve Having Four Reinforced Lugs Flanged Ends & Drilled to Din, Ansi, Bs-10, Is, Etc. this Valve Incorporates all the Design Modifications Based On Our Experience & is of Study Construction to Handle Abrasive Corrosive Media. BRIEF DETAILS OF PINCH VALVE Pinch Valve is a Seat less & Glandless valve. Pinch valve is a modified version of laboratory pinchcock. A rubber sleeve is protected under a cast iron casting. The fluid passing through do not come in contact with either body covering or any other metal parts of the valve except the sleeve. Hence the body and other metal parts are almost permanently not subjected to the corrosive action of the fluid. The flow through the valve is straight and full as that of a pipeline, when the valve is fully open. Further, the collar of the sleeve eliminates gasket. The valve is simple hand wheel operated of rising wheel type. Therefore the operation of the valve is just simple as other wheel operated valve. The in-between stoppage will allow the desired throttling. Thus the valve offers positive control over flowing media.   Applications Pinch valve finds its best application in handling corrosive slurry, abrasive media, liquid with solid suspensions and many others, which are difficult to handle with seat valve. Range The flange of the pinch valve can be supplied in accordance to BS, DIN, ASA & IS dimensions The range for the valve is from 15 mm TO 300 mm. Actuation The valve can be supplied with Electrical and pneumatic actuation. <? include("other-files/pinch-valve.html"); ?>       Operating Manual OF PINCH VALVE THE PINCH VALVE is a modified version of the laboratory pinchcock. A rubber sleeve is protected under a Cast iron or Aluminum split body casting. The valve is a simple hand wheel operated of rising wheel type. The operation of the valve is same as other hand wheel operated valve, it closes when moved in clockwise direction and opens when moved in anticlockwise direction. The in-between stoppage will allow the desired throttling. Thus the valve offers positive control over flowing media. The flow through the valve is same as that of a pipeline, when the valve is in fully opened condition. Further, the rubber sleeve eliminates the need of a gasket. PRELIMINARY PRECAUTION On receipt of the valve please check the position of the valve, as it is advisable to keep the valve in fully opened condition. Also check the position of the travel limit nut, if found loose then tighten the set screw of the nut. INSTALLATION The valve can be installed without any gasket unless it is required for some specific purpose. Tighten the nut of the flanges evenly & equally, but avoid too much tightening. After installation check the free movement of the upper & lower pinching bar by opening & closing the valve. The valve is then ready for the service it is installed for. MAINTENANCE If the valve is found leaking through the seat after sometime even though in fully closed condition, then set the travel limit nut by just taking it 1 or 2 threads above & then tighten. This will allow more room for traveling of rubber sleeve & ensure the valve to zero leakage. This problem sometimes occurs when the sleeve is slightly worn out, when used under abrasive condition. Further, The Rubber sleeve of the valve up to 2 (50mm) have a single lug on either side and it goes into the hollow passage of the pinching bar where it is fixed with the lug clamping screws. In the higher sizes above 2 the sleeves have two lugs on either sides and is fitted overlapping the pinching bar. DISMANTLING THE VALVE & REPLACING THE RUBBER SLEEVE When the rubber sleeve is ruptured or totally worn out then it is to be replaced with a new one. In this case first dismantle the valve by following the instructions. Remove the hand wheel. Open the Tie Bar nuts. Disconnect the spindle from the Horseshoe connection and remove it completely with the bridge. REMEMBER not to temper the set screw of the yoke bush, unless if required it should be completely tight. Open out the nuts & bolts of the split body of the valve. Remove the screw of the lugs from both the pinching bars. Now fit the new rubber sleeve & reverse the operation to assemble the complete valve.   NOTE It is advisable to keep a spare rubber sleeve for maintenance purpose, considering the self life of the Rubber as six months when packed & stored in dark. The Pinch valves should be stored in fully open condition only. We also offer complete spares of the valves, but request you to place your order a week in For more details please click on the links given below

• Country of Origin: India
• Color: Silver
• Feature: Corrosion Proof, Durable, Good Quality
• Material: Stainless Steel
• Usage/Application: Milk Vending Machine
• Pressure Range: 0.2 - 0.7 MPa
• Finishing: Polished

• Size: 250-300mm, 300-350mm, 350-400mm
• Certification: ISI Certified
• Application: Gas Fitting, Oil Fitting, Water Fitting
• Weight: 15-20kg, 20-25kg
• Color: Silver
• Feature: Blow-Out-Proof, Casting Approved, Corrosion Proof
• Pressure: High, Low, Medium
• Structure: Double Half Shaft
• End Connection: Butt Weld, Flanged, Screwed

Sanitary Stainless Steel Valves

• Material: Stainless Steel
• Brand: PARTHIV
• Pressure: 20KG
• Connector Type: Flanged End
• Material Grade: SS 202/304/316
• Colour: SILVER
• End Connection Type: Flanged
• Working Temperature: 80 deg cel
• Size: 1/2inch to 8inch
• Features: Withstand considerable pressure, Good quality plastic

• Country of Origin: Made in India
• Body Material: Stainless Steel
• I Deal In: New Only
• Usage/Application: Industrial
• Brand: Aqua
• Size: 1/2" TO 16"

We are well known for supplying of wide variety of Forged Steel Valve.

• MOC :: A 105 / F 304 / F 316 L
• Size Ranges :: 08 NB TO 50 NB
• Design And Mfg Std :: BS EN ISO 17292 (BS 5351) / 12516 / API 608 / 6
• Inspection And Testing Std :: BS EN ISO 12266 (BS 6755 Part – 1) / 12569 / API
• Face To Face :: Manufacturing
• Screwed End Connection Facing Std :: ASME B 1.20.1 /16.11/EN 12760
• Socket Weld End Connection Facing Std :: ASME B 16.11
• Buttweld End Connection Facing Standard :: ASME B 16.25

Appex make drop forged high performance forged steel ball valves gives outstanding performance in various applications like oil, gas, petrochemicals, steam, water etc. These valves are extremely reliable for high pressure application due to its best physical characteristics like refined grain structure and close molecules. These valves are being designed taking into consideration of online maintenance. Whenever any changes or maintenance require, Valves body can be removed from pipe line without dismantling valve.

We offer a varied range of needle valves made out of quality raw materials. Our wide range of needle valves include isolation valves, forged needle valve, high pressure needle valve and brass needle valve.

SAP Forged Steel Valves have been designed to meet the requirements of API 602/BS 5352/ASME B 16.34 Socket weld ends dimensions confirm to ASME B 16.11 Screwed ends dimensions confirm to ASME B 1.20.1 Outside screw and yoke construction The gland is of two piece self aligning type Back seat arrangement for Gate and Globe Valves. Valves meet the requirements of fugitive emission levels Shell category B as per MESC SPE 77 / 312

• Material: Cast Steel, Stainless Steel
• Application: Gas Fitting, Oil Fitting, Water Fitting
• Color: Grey, Silver
• Feature: Casting Approved, Corrosion Proof, Durable, Good Quality
• Type: Steel Ball Valves
• Condition: New
• Pressure: High, Low, Medium

Features STARTEK Cast Steel Ball Valves have been designed to meet the requirements BS 5351/ASME B 16.34API 6D-ISO 14313/API608/MSS SP 72 Face to Face and End to End dimensions conform to ASME B 16.10 / ISO 5752 / BS 2080/AP16D-IS014313/DIN End flange dimensions conform toASMEB 16.5/ ISO 7005-1/API 605/ BS 3293/DIN Butt weld end dimensions conform to ASME B16.25 Fire tested design toAPI 607/API 6FA/13S 6755-11 Flexible lip seats compensate for wear and changes in pressure Blow out proof stem construction Antistatic devices ensure electrical continuity between ball, stem & body Triple stem sealing ISO 5211 top pad for simplified gear/actuator mounting Valves meet the requirements of fugitive emission levels Shell category B as per MESC SPE 771312 Option One, two or three piece construction For low temperature and cryogenic services (cold box and non-cold box applications) extended bonnet as per BS 6364 available l Locking arrangement Gear, Electrical, Hydraulic or Pneumatic actuator available Soft seats are recommended for service temperature up to 260 Deg.0 and for higher temperatures a metal to metal seating offered. Materials Part Name Material Option Body   ASTM A 216 WCB / A 217 WC6 / A 217 WC9 / A 217 C5 / A 217 C12 / A 351 CF8 / A 351 CF8M / A 351 CF3/ A 351 CF3M /A 352 LCB Side Piece   ASTM A 216 WCB / A 217 WC6 / A 217 WC9 / A 217 C5 / A 217 C12 / A 351 CF8 / A 351 CF8M / A 351 CF3/ A 351 CF3M /A 352 LCB Ball   ASTMA351 CF8 /A351 CF8M /A182 F304 /A182 F316 /A182 F6a Body Seal   PTFE/Graphoil /Spiral Wound SS 316 with Graphoil Seats   PTFE / GET/ Graphite filled PTFE Stem   ASTM A182 F304 /A182 F316 /A182 F6a Gland Bush   ASTM A182 F304 /A182 F316 /A182 F6a Gland Packing   Graphoil/ PTFE Stem Packing   Graphite filled PTFE/Graphoil Gland Nut   Stainless Steel Stem Nut   Stainless Steel Lever   Carbon Steel with PVC Disc Spring   Carbon Steel Studs/Bolts   ASTM A193 B7 /A193 B7M/A193 B8 /A193 B8M / A320 L7 Nut   ASTM A194 2H/A 194 B7M/ A194 B / A194 8M / A194 4/7

• Material: Mild Steel
• Media: Water
• Color: Blue
• Finishing: Paint Coated
• Power: Manual
• Valve Type: Butterfly

• End Connection: WAFER TYPE
• Material: Stainless Steel
• Size: ALL SIZE
• Power: Manual
• Operation Type: By Lever, By Gear
• Brand: ASHOK

We offer high quality SS Needle Valve at very affordable market price. These needle valves are manufactured using very high quality raw material and very skillful workers. These can be tailor made according to the specification provided by the customers. These products are in great demand in critical environments such as petrochemical, fluid power, electronics, process machinery and other major industrial applications.

• Brand: Racer
• Material: Stainless Steel
• Material Grade: SS304
• Steel Grade: SS304
• End Connection Type: Threaded
• Size: 3x2 Inch
• Valve Size: 50mm
• Pressure: Medium Pressure
• Automation Grade: Semi-Automatic
• Color: Silver And Red
• Diameter: 3mm