Thermic Oil Dealers in Ahmedabad

For ensuring quality products at buyer's end, we check each and every product at diverse stages including production, packaging and delivery. For the attainment of complete client satisfaction, we offer them both online or offline payment procedures. In addition to this, we guarantee safe and secure transactions. Features : Correct formulation Excellent thermal stability Enhanced shelf life

It is a new generation heat transfer fluid with superior quality high viscosity index mineral base oilsblended with anti-oxidants& other additives enhances fluid’s longevity &ensures excellent thermal stability, providing a budget solution.

Hot Thermic oil is used as heating media. Air is heated by hot Thermic oil. Due to high temperature of oil, heat transfer area required is less than steam heater. Hence cost of Thermic oil air heater is less than that of steam heater for same, heat load. Higher air temp. Can be obtained in these heaters where as to obtaiv higher air temp. In steam heaters it requires high steam pressure.

• Speed - n -: 960 / 1450 / 2900 rpm
• Temperature: 350 ºC
• Working Pressure: 15 Bars
• Pump sizes – DN -: 32 mm to 100 mm

"Flowchem" Series PPC pumps are Centrifugal Pumps in Back Pull-out Construction , Horizontal, Center line Mounted, Single stage, End suction and Top Centerline Discharge Suitable for Thermic Fluid & Hot Oil also.

• Working Pressure: 2.5 to 3.5 Kg/cm²
• Size Range: 1/2″ to 12″

We Manufacture Quality Valves of almost all types for a wide spectrum of users in the Process & Chemical,Refineries & Petrochemicals,Fertilizers,Drugs & Pharmaceuticals,Thermal Power Stations,Nuclear & Atomic Power Stations,Textiles,Dyes & Intermediates, Paints & Varnishes,Sugar,Breweries & Distilleries,Soaps & Detergents, Steel Plants,Food & Oil Industry, Solvent Extraction Plants, Sewage, Effluent & Water Treatment, Cooling Water,Ship Yards and Marine Management,Water Works,Pulp & Paper,LPG Bottling Plants, Onshore & Offshore platforms, Slurry & Ash handling.

The "Multitech Engineers" The fully automatic Three pass heating systems essentially comprises of a fully automatic packaged Oil/Gas fired heater. As a result thermic fluid can be heated up to 300°C at near atmospheric pressure, with efficiency as high as 87% on NCV of Oil/Gas fuel.The capacity ranges from 50000 kcal/hr to 15 lacs kcal/hr in Oil/Gas firing

Thermic fluid oil Low fuel oil temperature (F.O. fired only).Flame monitor by photocell (LDR).Circulating pump motor interlock.Coil from Seamless ASTMA 106 GR-B Pipes.Independent Drive for Fuel Pump 1440 RPM.

• Outlet Temperature(max): 300oC
• Electric supply: 415 Volts + 5% 50 H2 3ph – 6Wire.

heat output (kcalhr) : 50.000, 1.00.000, 2.00.000, 4.00.000, 6.00.000, 10.00.000, thermal efficiency : 87%, thermic fluid pump motor : 2.0h.p. 3.0 h.p.7.5h.p. 10.0h.p. 12.5h.p. 25.0h.p. Thermic fluid pump rating : 6.000ltrhr, 12.000ltrhr, 18.000ltrhr, 30.000ltrhr, 36.000ltrhr, 45.000ltrhr

This system is forced circulation fully automatic thermic fluid heater where thermic fluid is circulated in a closed loop through heater and user equipment circuit where the heat is dissipated to process. The same thermic fluid is re-circulated through heater for heating. The thermic fluid heater gives high temperature upto 300 oC using thermic fluid oil at near atmospheric pressure as compared to steam heating which requires 85 KgCm2 pressure.

• Packaging Type: Barrel
• Color: LIGHT YELLOW
• Brand: MAK THERMIC FLUID A
• Usage/Application: Heat Transfer oil
• Packaging Size (litres): 210 LTR
• Flash Point (deg. Celsius): 238 DEG CELSIUS
• Density (deg. Celsius): 0.859 density
• Boiling Point (deg. Celsius): 480 deg celsius
• Pour Point (deg. Celsius): -18 DEG.CELSIUS
• Max. Temp. (deg. Celsius): 310

Thermic Fluid Oil, Electric Furnace, Industrial Heater

Thermic Fluid Oil, IBR Steam Boiler, Thermic Fluid Heater

thermic fluid, edm oil, cutting fluids, thermal oil, Heat Transfer Oil