Gate & Sluice Valves Dealers in Bakrol, Ahmedabad

• Material: Various Materials
• Material of construction: PP/PTFE/SS316/SS304
• Note: Process connection shall be as per Client’s/process requirement
• Type: Pressure Relief Valve
• Features: Quickly Releases Over Pressurized Liquid, Activated Automatically

Pressure safety valves are used in dosing/metering pump discharge line, A Pressure Safety Valve (PSV) is a type of valve used to quickly release over pressurized liquid from the discharge line in order to avoid over pressurization and potential process safety incidents. PSVs are activated automatically when pressure exceeds prescribed pressure limits in order to return equipment pressure to a safe operating level.

• Body/Bonnet: WCB /SS 304/SS 316
• Trims: 18 cr 8ni/CF8/CF8M
• MFG: API 600
• Testing: API 598
• Ends: Flanged to ANSI B 16.5/16.47 150#/300#
• Hyd Body Test: 450 psig (32 kg /cm2)
• Hyd Seart Test: 315 Psig (22 kg/cm2
• Size: 80mm to 900mm
• Available: Also Available on Extended Shaft
• Item Code: OFF-HV-018

• CAST STEEL: STAINLESS STEEL

We offer gate valves are primarily designed to start or stop flow, and when a straight line flow of fluid and minimum flow restriction are needed. In service, these valves generally are either fully open or fully closed. The gate (also called wedge) of a gate valve is completely removed when the valve is fully open; the wedge is fully drawn up into the valve bonnet. This leaves an opening for flow through the valve at the same inside diameter as the pipe system in which the valve is installed. A gate valve can be used for a wide range of liquids and provides a tight seal when closed. advantages of using gate valves: good shutoff features gate valves are bidirectional and therefore they can be used in two directions pressure loss through the valve is minimal.

Design Features : Design and Manufacturing : API 6D Inspection and Testing : API 6D Inspection and Testing : API 6D End Flanges dimension : ASME B 16.5 BW end Dimension : ASME B 16.25 Face to Face & End to End Dimension : API 6D ASME B 16.10 Design : SLAB Type, Through conduit passage – Piggable Anti-friction ball thrust bearing in yoke sleeve Drain & Vent Connection, Lifting Lugs & Support Legs, Double block & bleed, fire safe design.

• Brand Name: Fu-Tech, Marck
• Material: Alloy Steel, Carbon Steel, Forged Steel, Stainless Steel, Cast iron
• Color: Black, Brown, Grey, Sky Blue, White
• Condition: New
• Pressure: High, Low, Medium
• Application: Gas Fitting, Oil Fitting, Water Fitting, Power plant
• Size: 100-150mm, 150-200mm, 200-250mm, 250-300mm, 300-350mm, 350-400mm, 400-450mm, 450-500mm, 50-100mm, Tailor made
• Certification: Msme

If you are looking for Industrial Valves please contact us 

Wedge Gate Valves of different ratings are offered by us. These valves have been designed for maximum efficiency and are corrosion resistant. They are available in different sizes for the client to choose from according to the applications. We deal primarily in bulk sized orders Marginal orders are also frequently processed by us as and when requested by our clients. Client satisfaction is our top priority.

• Size Range: Class
• 2" - 24": 150
• 2" - 16": 300
• 2" - 12": 600
• 2" - 12": 900
• 2" - 6": 1500

We are manufacturing valves under brand name SABA. We also dealing in ZED make manual valves and Aira, Rotex make Automation products.   We manufacture SABA make wide range of Gate Valves which include knife gate valves,forged and cast gate valves having screwed / Socket / Flanged Gate valves. These valves are renowned all over for their premium quality. With the quality assurance we are the largest flanged gate valves supplier in India. We also manufacture these gate valves according to customer specifications. The quality of these valves is intact. They are properly inspected and verified before sending them to client. Uses of acme quality metal and flawless designs which enhance the performance of these valves have made us stand much ahead from the other manufacturers in India.Gate Valves are Outside Screw & Yoke, Bolted bonnet & with Rising stem. The “STRAIGHT THROUGH BORE” design assures minimum turbulence, erosion and resistance to flow caused by pockets & recesses. Gate Valves are mainly used where minimum pressure drop is a requirement.Design Features : Designed for exceptionally low pressure drop Back seating arrangement permits the replacement of packing with valve under fully open condition. Two piece design of gland flange provides centralizing effect to the gland sleeve, thus producing a uniform clamping pressure on the packings. Material Structure : End Connection : Flanged end raised face, Butt weld end, RTJ, etc. Operation : Hand wheel, Gear operator, Electrical Actuator, Pneumatic, Hydraulic Shell :WCB, WC1, WC6, WC9, LCB, LCC, LC3, C5, C12, CF8, CF8M, CF3, CF3M, CF8C, CN7M, CD4MCu, Hastalloy, Inconel, Duplex Stainless Steel Trim :13% Cr. Steel, 304, 304L, 316, 316L, 321, 347, Monel, Duplex Stainless Steel Standards "Design Standard :  API 600 Testing Standard :  API 598 Face to Face :  ASME B 16.10 End Connection : Flanged End : ASME B 16.5 Butt Weld End : ASME B 16.25 Pressure Temperature : ASME B 16.34 Valve Operation :Operator : Hand Wheel : Size Range : 2” – 10” – Class 150, 300, 600 2” – 4” – Class 900 & 1500 Operator : Gear Operator Size Range : 12” & above – Class 150, 300, 600 6” & above – Class 900, 1500

• Finishing: Coated
• Condition: New
• Type: Gate Valves

Series 80 back pressure control valve has a conical body, a diaphragm for sealing and bonnet with internal mechanism.   Key Features: Cost-effective modular design Optimized for size against maximum pressure control Completely adjustable pressure control range Option of Silicon or FKM(FPM) Diaphragm available Fully Autoclavable Various internal surface finish available

• Manufacturing Standard: BS 5163 / IS14846
• Size Range: 32 to 1500mm
• Pressure Ratings: PN10, PN16

These valves are available in non rising as well as rising spindle type suitable for clear water up to 450 C. These valves are designed with total compliance with applicable design and testing standards. All designs are validated for stress analysis. Sluice valves find wide application in water works, water/effluent/sewage treatment plants. These valves are available in non rising as well as rising spindle type suitable for clear water up to 450 C. These valves are designed with total compliance with applicable design and testing standards. All designs are validated for stress analysis. Sluice valves find wide application in water works, water/effluent/sewage treatment plants. FEATURES Rigid and sturdy design Low pressure loss across the valve Suitable for clear water up to 45 C and 5000 ppm turbidity, other fluids with maximum pressure / temperature conditions within the scope of IS:14846 Long service life and leak-tightness even after thousands of open / close cycles APPLICATIONS Water works Water / Effluent / Sewage treatment plants Fire Fighting Power

• Bore Sizes: 1-13/16
• Temperature Class: K-V
• Material Class: AA - FF
• Working Pressure: 5000 PSI - 15000 PSI
• Product specification Level: PSL1 - PSL3
• Performance Rating: PR1 - PR2

Ball Valves, Ball Valves, Ball Valves, wafer swing check valve

Api Gate Valve, Api Ball Valve, Api Globe Valve, Api Pumping Units

vacuum relief valves, pilot operated valves, emergency relief valves

Industrial Valves, lift check valves, Ball Valves, Air Valves

Pressure Reducing Valve, Safety Valves, Ball Valves, Pressure Regulators

high pressure solenoid valve, Rubber Unisex Household Gloves