Back Back
Cable Clamp holder, Cable Grommet
Requirement of accessories for External Towers with Transmission / Reception antennae installed on them are catered to through various products. Cable routers, Cable Clamp holders, Cable Grommets, Cable Clamps and External Cable Trays are some of the products manufactured in various sizes and to different specifications.
...more
St Adapters
he ST adaptors are interconnection device, which are used to provide connection between two ST type connectors. Features Stainless metallic round body Environmentally stable Designed for Single Mode ST connectors Absolute repeatability Split Zirconia Ceramic Sleeve Complete alignment with beyonet coupling mechanism Mounting via a locknut and washer combination Applications Telecommunication network Local area network Testing instruments
...more
Splicing Shelf
Suitable for all types of single Fibre OF Cables Single piece moulded body Constructed from ABS Push fit arrangement for fixing the splice holder / fan out transition block on the tray Pre-defined place for fixing splice holder / transition block of the fan out unit Designed to store fibre splices and extra length of fibres in systematic & secured manner without change in attenuation Protects minimum bend radius of each optical fibre Pre-installed identification system for complete end to end traceability The capacity of each splice tray can be determined by the type of splices stored in each splice tray. Each tray can be configured to accommodate splices of: 12 fibre ribbon with 12 fibre ribbon / individual fibre splices (2 splices stored in each tray-single circuit / element basis) 12 fibre ribbon with 12 individual fibres (12 splices in each tray) 12 individual fibres with 12 individual fibres (12 splices in each tray) Applications Long distance Optical Transmission Network Datacomm Network Management of large volume of fibres Specifications Height (mm): 2200±2% Width (mm): 900 ±2% Depth (mm): 300 ±2% No. of cables: 12
...more
Splicing cum Patching Shelf
Specifically suitable for Ribbon type of Optical Fibre Cable Single piece moulded body Constructed from ABS Well protected from accidental & malicious damages Capable of holding 12 numbers of FC / SC / ST or LC type adaptors Splicing area available on both sides of the tray Push fit arrangement for fixing the splice holder on the tray Each tray has a predefined place on both side of the tray for fixing the transition block of the Fan Out unit Tray is designed to store fibre splices and extra length of fibres in systematic & secured manner without change in attenuation Protects minimum bend radius of each optical fibre Pre-installed identification system for total end to end traceability
...more
Splice Protection Sleeves
The Splice Protection Sleeves are designed to completely encapsulate splice and offer environmental and mechanical integrity of coating or buffer of optical fibre after splicing. Splice Protection Sleeves are manufactured using very advanced and precisely controlled manufacturing technology. Features Outer tube conforms to MIL-I 23053 / 5 class 2 Inner tube made from Polyolefin Copolymer (Ethyl Vinyl Acetate) Resistant to heat shocks Effectively encapsulate fusion splices Better corrosion resistance even in coastal environment Sleeves are pre-shrunk which ensures integrity of assembly during transportation Available in different types, diameters and lengths as per customer requirement. Standard Sleeve Available in 60 mm & 45 mm lengths Diameter after shrinking is 3 mm Available in clear & colored versions Slim Sleeve Reduced dia components for a smaller finish Available in 60 mm, 45 mm & 40 mm lengths Diameter after shrinking 2.5 mm Dielectric Sleeve Non metallic central strength member Resistance to corrosion & electricity Available in 60 mm & 45 mm lengths Diameter after shrinking 3 mm / 2.5 mm Micro Sleeve Used where space is very limited Available in 35 mm & 25 mm lengths Recovered dia 1.5 mm Ribbon Sleeve Suitable for 4 to 12 fibre Ribbon High mechanical strength with ceramic strength member Standard length 40 mm Applications Protection of single fibre splices Protection of Ribbon fibre splices Specifications Outer Tube Polyolefin Working Temperature: -50°Cto 125°C Min. Shrink Temperature: 90°C Ultimate Strength: 220 Kg / cm² Elongation: 650% Specific Gravity: 0.95 Fungus Resistance: Inert Solvent & Acid Resistance: Good Toxicity: None Ends: Smooth, even & consistent Strength Member (Single Fiber Sleeves): 316 Stainless steel with rounded and polished ends Strength Member (Ribbon / Dielectric sleeves): Polished ceramic (white) or Quartz (transparent)
...more
SC Adaptors
he SC adaptors are interconnection device which are used to provide connection between two SC type connectors. Features High precision plastic moulded body Compact & light weight Absolute repeatability Low insertion loss Excellent return loss Push-Pull type arrangement Split Zirconia Ceramic Sleeve Available in SM & MM Mounting via two metal locking tabs attached to the body or use of two self tapping screws Applications Local area network CATV network Fibre optic sensors Testing instruments
...more
Patch Cords
FC Connector feature high stability and low insertion loss for use in a wide range of applications. FC Connector design offers high performance. Features Tuned for low connection loss with movable keys Keyed for repeatable performance Stable against mechanical or environmental shock PC, UPC and APC available for maximum fiber contact with Simplex & Duplex options Excellent back reflection Applications Long distance Optical Transmission Networks Active device termination Optical Measuring Instruments reconnections SC Connector The SC Connectors are designed to use the latest polymer and Zirconia Ceramic ferrule technologies. The push-pull mating design allows this connector to be ideal for limited space requirement. Features High reliability & performance High packaging density Easy connection and disconnection (push-pull type) PC, UPC and APC available for maximum fiber contact with Simplex & Duplex options Plastic-moulded, rectangular connector housing prevents rotation and enables high-density mounting. Applications Local area Networks Telecommunication Networks Active device termination
...more
OPTICAL FIXED ATTENUATOR
he Optical Fixed Attenuators are designed for use during the measurement of optical power, optical loss, transmission rate and other optical transmission characteristics during installation and maintenance of Fibre Optic Communication equipment and optical fibre links. The Fixed type attenuator uses air gap technology to achieve attenuation unlike conventional filters or light path discontinuities, which results in repeatable performance and greater life of connector interfaces. Features Available in FC-PC type Stainless Nickle / Brass square body Excellent repeatability Attenuation stability Environmental stability Easy installation Excellent return loss Designed to handle high power input Air gap technology Mounting via two self-tapping screws Applications Telecommunication network Local area Network Testing instruments CATV Fibre Optic Sensors Video network testing Specifications Operating Temperature: -40°C - +75°C Wave Length: 1310 nm / 1550 nm Over 500 repeatable reconnections Attenuation 3, 5, 10, 15, 20, dB(Customized values available)
...more
OPTICAL FIBRE SPLICE CLOSURE (601)
We are offering optical fibre splice closure (601). The optical fibre splice closure (ofsc) 601 provides a perfect solution for the protection of the junction points of optical fibre from environment, vibration, aggressive media, stress circling, impact and water. It may be used in underground, aerial, butt joint and direct buried applications.
...more
Optical Fibre Splice Closure
The Optical Fibre Splice Closure (OFSC) 601 provides a perfect solution for the protection of the junction points of optical fibre from environment, vibration, aggressive media, stress circling, impact and water. It may be used in underground, aerial, butt joint and direct buried applications. Features Compact and modular design for easy installation Comprises of a Dome and a Base Suitable for all types of optical fibre cables Water proof and air tight Excellent cable clamping and FRP holding arrangement for all cables Cable ports sealing through Thermo Shrink Sleeves Repeatedly openable mechanical sealing of Base and Dome eliminating clumsy heat shrink procedure for sealing Provides straight through or branched out joints upto four cables & entry for one uncut cable Contains Fibre Organizer trays to hold fibre splice, one tray holding upto 24 splices Capacity to accommodate upto 6 nos. of Fibre Organizer trays and house upto 144 splices Complete kit with consumables available Applications Long distance Optical Transmission Networks Jointing of all types of cables Datacom Networks Specifications Length: 490mm ± 5%, Collar dia: 165mm ± 5% Outer dia of Dome: 146mm ± 5% Cable entry ports: 4 Round & 1 Oval port Max. nos. of splice tray: 6 each of 24 splice capacity Operating Temperature: -30°C - +70°C
...more
OPTICAL FIBRE RIBBON FAN OUT ASSEMBLY
The Fanout Assemblies are designed for use in Patch Panels where mass fusion splicing take place. These fanout assemblies are available with a variety of interface connectors. Each assembly has a designated connector on the fanout side and no connector on the ribbon side. Fanout Assemblies provide a transition from Ribbon fibres to individual fibres in a ribbon. Features 4, 6, 8, and 12 fibre count available compact and light weight high tensile strength rugged construction for long life and durability PC and Angled PC available Available in Single Mode & Multimode Excellent return loss Applications Telecommunication network Active device termination Long distance optical transmission network Datacom network Specifications R.L: PC
...more
OPTICAL FIBRE NON RIBBON FAN OUT ASSEMBLY
The Fanout Assemblies are designed for use where mass fusion splicing take place. These fanout assemblies are available with a variety of interface connectors. Fibre Optic cables of upto 12 fibres pass through transition block giving out 12 individual fibres with connectors in the shape of a Fanout. This provides a comprehensive connectorization method in high density network connectorization. Features Compact and light weight High tensile strength Excellent return loss Robust & rigid under all conditions 6, 8 and 12 fibre count available Applications Telecommunication networks Long distance optical transmission network Fibre to home Management of large volume of fibres Specifications R.L: PC
...more
OPERATION RACKS AND PANELS
These Racks and Panels are manufactured to stringent specifications to meet varied requirements of communications and are also manufactured to customer’s design and specifications. I. SHOWER TEST: To check integrity of the Racks and Panels against water penetration. Spray - water Flow Rate - 40 Ltrs / min. / head Number of heads - 4 Head to Sample - 400 ? 100 mm Sample Position - Laying Down Requirement - No Water ingress II ENVIRONMENTAL CYCLE TEST: To determine working capability of the Rack and Panel for climatic conditions. Lowest Temp. - -15°C Highest Temp. - 60°C Dwell Time - 4 Hrs. Transition Time - 2 Hrs. Cycle Duration - 10:30 Hrs. Number of Cycles - 10 III VIBRATION TEST: To check effect of Vibrations caused due to tempest, storm and other inclement weather conditions. Planes - 3 (X, Y & Z axis) Sweep - (10-300) Hz ±2% at 1 octare±10% per min. (a) Sine Sweep (10-28) ?? 1 Hz. 0.1” (2.5mm) double amplitude Time - 2 Hrs. each axis These Racks and Panels are tested for axial Tension of 70 Newtons applied longitudinally for 10 min. on the cables and for Pig Tails / Patch Cords the test is conducted at 25 Newtons for 10 min. (to simulate effect of accidental pull).
...more
LC Adaptor
The LC adaptors are interconnections device which are used to provide connection between two LC type connectors. Features High precision plastic moulded body Compact & light weight Low insertion loss & Excellent return loss Split Zirconia Ceramic Sleeve Available in SM & MM Mounting via two metal locking tabs attached to the body or use of two self tapping screws Applications Telecommunication network Testing instruments Datacomm networks Specifications Insertion Loss: < 0.1 dB Wave Length: 1310 nm / 1550 nm Operating Temperature: -30°C - +70°C
...more
FIBRE OPTIC TERMINATION BOXES
The fibre distribution termination box (fdtb) is used to terminate metal free and armoured optical fibre cables of various designs like loose tube, central tube and slotted core etc. Oftb is suitable for terminating optical fibre coming from the line and connecting the optical fibres to the pigtails by splicing.
...more
fibre optic patch panels
The Optical Fibre Patch Panel is suitable for terminating optical fibre cables coming from the line and connecting the optical fibres to the pigtails by splicing. These pigtails are connected to the pre-installed adaptors at one end and from the other end output can be taken to active devices using patch cords. Patch Panel provides splicing, termination and distribution ina single unit. Features Compact and robust construction. Available in wall mounting and rack mounting versions Accessibility from the front & top sides for testing and easy handling Main body constructed from internal stress free CRC sheet. Aluminium sheet body also available. Powder coated finish enables operation even in coastal areas Dust and insect ingress resistant Provision to store extra lengths of fibres Provision of two inputs & two output ports Contains Fibre Organizer trays to hold fibre splices, capacity of each tray upto 24 splices Capacity to accommodate upto 6 nos. of Fibre Organizer trays and house upto 144 splices Design ensures bend radius of stored pig tails & patch cords above the critical value Capacity to hold adaptors of FC, Sc & ST type as required Complete Kit with consumables available Applications Long distance Optical Transmission Networks Termination & Distribution of OF Cables Datacom Networks Specifications Physical dimensions suitable for installation in 19” rack with multiples of ‘U’ as stand alone system Operating Temperature: -30°C - +70°C
...more
FIBRE OPTIC INSTALLATION TOOL KIT
The Fibre Optic Installation Tool Kit contains all the generalized tools required for installation and operation of Fibre Optic Cables. It helps in proper and methodical installation and assembly of the OF cable accessories without affecting any damage to the cable and optical fibre properties. Features Robust, durable and portable tool box Tools are housed in specific slots in the attractive tool case Tool box is lockable which ensures security Suitable for installation of all types of optical fibre cables Cost competitive and value for money Mass customization possible. Applications Installation of various equipments Jointing of all types of cables
...more
FIBRE OPTIC DISTRIBUTION FRAMES
We offer fibre optic distribution frames. The fibre distribution frame (fdf) organizes optical fibre pigtails and patch cords at distribution nodes in the fibre network. It connects optical line termination box on one side and optical line termination equipment on the other side. The fdf also provides facilities for patching, routing and re-routing of various communication channels
...more
FIBRE OPTIC CABLE TESTING MACHINES
We are offering fibre optic cable testing machines. Mechanical testing of optical fibre cables is done to determine the quality of the optical fibre cable to withstand mechanical stresses and strains likely to be encountered in its lifetime. Each mechanical characteristics can be tested on veekay testing machine for the particular test. These are: 1. Tensile testing machine 2. Repeated bending testing machine 3. Crush testing machine 4. Torsion testing machine 5. Impact testing machine
...more
FDMS - OUTDOOR
FDMS Outdoor provides management of very large volume of Optical Fibres of a cable or number of cables with flexibility and reliability in all environment. It is designed to be used in External (Outdoor) environment for jointing and branching Optical Fibre Cables and caters to splicing of individual as well as ribbon fibres. It provides the perfect solution for the protection of the junction points of optical fibre from environment, vibration, aggressive media, stress circling, impact and water ingress is tested upto IP65 Standard.
...more
FDMS Outdoor
FDMS Outdoor provides management of very large volume of Optical Fibres of a cable or number of cables with flexibility and reliability in all environment. It is designed to be used in External (Outdoor) environment for jointing and branching Optical Fibre Cables and caters to splicing of individual as well as ribbon fibres. It provides the perfect solution for the protection of the junction points of optical fibre from environment, vibration, aggressive media, stress circling, impact and water ingress is tested upto IP65 Standard. Features Modular design for easy installation. Mass customization possible. Comprises of a Dome and a Base Extremely user friendly Suitable for ribbon and non-ribbon optical fibres Excellent cable clamping and ERP holding arrangement for all cables Cable entry through ports and sealed by Thermo Shrink Sleeves Repeatedly openable without requiring clumsy heat shrink procedure for sealing Mechanical sealing of Base & Dome with single clamp without screws Reliable moisture tight casing Dust proof to keep dust and insect from setting inside Flexible installation and convenient operation and maintenance Push-fit mounting arrangement of splicing trays on Universal Mounting System (UMS) provides ease and flexibility in installation, operation and maintenance The capacity of each splice tray can be determined by the type of splices stored in each splice tray. Each tray can be configured to accommodate splices of Either 12 fibre ribbon with 12 fibre ribbon / individual fibre splices (2 splices in each tray – single element / circuit basis) 12 fibre ribbon with 12 individual fibres (12 splices in each tray) 12 individual fibres with 12 individual fibres (12 splices in each tray) Splice tray is designed to store fibre splices and extra length of fibres in systematic & secured manner without change in attenuation Protects minimum bend radius of each optical fibre Pre-installed labels provide complete fibre identification & traceability Complete kit with consumables available Applications Long distance Optical Transmission Network Single circuit assemblies Jointing of all types of cables Management of large volume of fibres Specifications Length (mm): 700 ± 5%, 360 ± 5% Dia of the Dome (mm): 250 ± 5% (without collar) No. of circular ports for cable entry: 6 nos. Inner diameter of each circular port: 22 mm No. of Oval port: 1 no. Inner dimensions of oval port: 80 x 30 mm Max. capacity of splicing trays: 48 nos.
...more
FDMS- CENTRAL EXCHANGE LOCATION
we offer Fdms- Central Exchange Location. FDMS for Exchange provides a complete system with facility of splicing, termination, distribution, identification with complete wiring with pig tails & patch cords. It provides a flexible cable management system using a variety of shelves. It provides management of very large volume of optical fibres of ribbon and non-ribbon type cables with flexibility & reliability in all environment of access network.
...more
fc adaptors
The FC adaptors are interconnection device, which are used to provide connection between two FC-PC type connectors. Features Stainless Nickle / Brass square body Extremely accurate key alignment Environmentally stable Absolute repeatability Low insertion loss Excellent return loss Available in SM & MM Splitted Zirconia Ceramic Sleeve Mounting via two self-tapping screws Applications Telecommunication network Local area network Testing instruments Fibre distribution system Fibre optic sensors
...more
DUPLEX CABLE, FURCATION TUBINGS
Simplex & Duplex tight buffered fibres are designed for indoor use of signal, video and data communications. These fibres provide easy connection and handling where fibre density or connection density is large. These can easily be installed in equipments, Fibre Distribution Management Systems for Exchange, Building Premises, even Outdoor and other distribution applications. Features Light weight for installation in trays Economical Flexible & Flame retardant Excellent optical performance Acrylate primary coating & PVC outer jacket Applications Local area networks Used for Patch cords & Pig Tails High density optical networks High speed voice, vides & data networks Furcation Tubings Furcation Tubings are used for various routing coverings and protection in Fibre Optic applications. Furcation Tubings are available in various diameters & colours. Features Light weight for installation in trays Economical Flexible
...more
Splice Protection Sleeves
The splice protection sleeves are designed to completely encapsulate splice and offer environmental and mechanical integrity of coating or buffer of optical fibre after splicing. Splice protection sleeves are manufactured using very advanced and precisely controlled manufacturing technology.
...more
Reviews & Ratings
Write a ReviewBe first to Rate
Rate ThisOpening Hours
Share your Correspondence Details to receive messages from Veekay Connectors (P) Ltd.
Post Free Ad