Marigold Paints Vallabh Vidhyanagar, Anand, Gujarat

We are a notable name for availing premium Rosalee Oil Primer. We manufacture and supply Rosalee Oil Primer for extensive usage. Rosalee Oil Primer is essentially meant for vehicle refinishing.Scope : This primer is essentially meant for vehicle refinishing, which should dry much faster than any synthetic primerand should be capable of accepting N.C. Putty after 2 hrs. Without causing any “bleeding.”Areas of application : All types of vehicles that are to be painted with N.C. Lacquers or very fast drying synthetic enamels.Surface preparation : The vehicles, which are to be repainted, have some kind of coating. The same should be removed preferably, byusing eurostrip (paint remover) and should show bare metal. Invariably, rust is visible which should be got rid ofusing rustosan p-07, which also helps in removing traces of oil and grease. Directions for Use : Once the bare metal of a vehicle has been made free from rust and from traces of oil and grease, thin down theprimer using thinner 011 (to get spraying viscosity) and start spraying. No special skill is needed. There is noneed to wet sand the primer because the same can be done after putty application.Notes : Do not use very high pressure, which will result into uneven, sandy finish because of dry spray.

We are engaged in making available the best quality Chloru Chlorinated Rubber Primer in market. The Chloru Chlorinated Rubber Primer is perfect to be used on steelwork and concrete surfaces of fertilizer and chemical industries, battery rooms, pulp plants, etc. Scope : Single pack chlorinated rubber based fast drying high build primer.   Areas of Application : The product is recommended for use on steelwork as well as on concrete surfaces of fertilizer and chemical industries, battery rooms, pulp and paper plants, breweries, bottling plants, swimming pools, marine and harbour installations.   Surface Preparation : Steel : Remove grease, oil and other contaminants preferably by using Rustosan. Blast cleaning is also recommended. The surface should be clean and dry before application of a suitable primer. Concrete : Allow curing at least for 8 weeks. Remove all alkalinity by washing the surface thoroughly with 3% - 5% phosphoric acid. In case of aged concrete surface, sandblasting is ideal. Wire brushing can do to remove any oil/soil/salt deposit or lactate deposit. Make the surface free of all loose dust and moisture. In non-critical areas where blasting is not possible, water jet washing and hard wire brushing are minimum requisites.   Application :Stir the contents thoroughly before and during application. Brush/Roller : Apply without thinning. If required, 5% Rosalee Thinner 022 may be used. Airless spray : Apply without thinning. Galvanized and Rosalee aluminum : Degrease and abrade the surface and apply a coat of Rosalee Wash Primer Metaprime-H followed by any of the above systems.

We are a well-known Rosalee Synthetic Primer Manufacturer and Supplier located in Gujarat. An iron or wooden surface needing white topcoat must be covered with Rosalee Synthetic Primer. We are offering premium Rosalee Synthetic Primer in proper packing. Scope : Mild steel sheets, needed by a large number of engineering industries, come wavy, especially when they are hot rolled. In order to get aesthetic finish, the waves must be eliminated. The easiest way is to apply a coat of primer surfacer and on the dried film of which, putty must be applied. Generally, the primer surfacers are available in grey shade. If the finishing coat is white or very pastel, the grey colour needs efforts (more coats) to cover the surface. And therefore, we offer synthetic primer surfacer white. Areas of Application : Any iron or wooden surface needing white topcoat must be covered with white primer surfacer.   Surface Preparation :Please refer to our pamphlets on : Surface preparation of metals Surface preparation of wood   Directions for Use : Stir well. Adjust viscosity for brushing or for spraying. The surface should be puttied and well sanded. Start brushing or spraying.

We manufacture and supply the best quality Rosaee Primer Zinc Chrome in market. Rosaee Primer Zinc Chrome, available with us, is known for offering excellent corrosion resistance. Avail Rosaee Primer Zinc Chrome from us at very reasonable prices. Scope : As against red-oxide, zinc chrome offers better corrosion resistance. Reason: under high humidity condition, zinc chrome dissociates into zinc ions and chromic acid ions. Whereas zinc ions offer protection against corrosion, chromic acid ions, offer passivity to the iron surface, which means longer and better protection of steel, fromrusting. Besides, it offers adhesion of any synthetic paint system on a galvanized or aluminium surface.   Areas of Application : All steel and aluminium surfaces including galvanized steel. Why apply zinc chrome primer to a galvanizedsurface, when galvanization by itself is ideal for protection against atmospheric corrosion? No galvanized surface will permit adhesion of any synthetic paint because of the development of white rust on its surface.   Surface Preparation : Please refer to our pamphlet on “surface preparation for metals”.   Directions for Use : Stir the primer. Use thinner to adjust viscosity for brushing or for spraying. The surface should be free from oil/rust.   Note : The genuine primer zinc chrome is expensive. To achieve economy, we also offer primer zinc chrome to is 104-p where “p” stands for performance guarantee. The content of zinc chrome pigment is 5-6% while the corrosion resistance is achieved by incorporating a special rust-preventing compound.

We are a prominent Manufacturer and Supplier of Acrythane 2000 HI-Solid Polyurethane Auto Finish. Acrythane 2000 HI-Solid Polyurethane Auto Finish is the best product for solving all the problems of vehicle refinishing. Avail Acrythane 2000 HI-Solid Polyurethane Auto Finish from us at very affordable prices. Scope : Acrylic-isocyanate P.U system is the world leader, when it comes to repainting (refinishing) of vehicles. Being based on acrylic polyol, it is non yellowing and is faster drying in comparison to polyester P.U system. Acrythane 2000 is our answer to solve all the problems of vehicle refinishing. To ensure non yellowing properties, we use only aliphatic isocyanate.   Areas of Application : Any vehicle, two wheeler; three wheeler; commercial vehicle; bus or car, which need re-painting of ferrous; nonferrous or even plastic parts of the vehicle, can be coated with acrythane 2000, to get a world class finish with extreme gloss.   Surface Preparation : Remove old paint to see bare metal. This can be done with eurostrip. Remove oil/wax from upon the surface, using rustosan p-017. Apply a thin coat of metaprime-h (two pack wash primer), which is a must for aluminium body or parts. Fill up the dents with eurofill (polyester putty) and do not use N.C. Putty. Wet sand the surface using medium coarse emery paper to get a silky smooth surface. Allow the surface to dry thoroughly. Apply one coat of acrythane primer grey ; allow to dry for 3-4 hours and wet sand, with medium coarse emery paper. Allow to dry thoroughly. Apply preferably wet on wet, two coats of acrythane surfacer grey. Alternatively, apply the second coat after an interval of 3 to 4 hours. When the film is hard dry, wet sand, using the finset emery paper, to get a silk smooth surface. For plastic parts, like bumpers, dashboard etc. A coat of adpro (adhesion promoter) is a must for adequate adhesion of acrythane 2000. On such areas, putty,primer-surfacer are not required. Now, the vehicle is ready for application of acrythane 2000.   Directions for Use : Prepare the surface according to the heading “surface preparation”. Mix base and hardener in recommended ratioand thin down to 20-22 seconds in ford cup no.4 @ 30o c. Use only P.U thinner 099. In case of humidity in excess of 60%, blow hot air in the paint shop or in the spray booth. Ideal solution will be to install dehumidifier like bryair apply three coats, each at an interval of 3 – 4 hours.   Notes : P.U hardener is very sensitive to moisture. Keep the containers tight, each time after use. Normal thinners can ruin the P.U finish. Use only thinner 099. We offer adequate quantity of thinner 099, along with the base and hardener. Acrythane 2000 is also available as clear (varnish) for enhancing the gloss of any colour. It is fortified with uv inhibitor and thus, it lasts long as exterior finish.

We are engaged in manufacturing and supplying the finest Eurocoat Auto Finish. Eurocoat Auto Finish, available with us, is suitable for all kinds of vehicles. The Eurocoat Auto Finish is used for painting large and small engineered articles. Scope : In India, everyday more and more vehicles come on the roads. The vehicle production includes two wheelers, three wheelers, small and large commercial carriers. Now, the road conditions have remained more or less same for the past two decades.net result; minor and major accidents. Each owner of the vehicle feels very proud of his possession and flaunts the vehicle as status symbol. No one wants his or her vehicle with dents, scratches or rust. At least once a year, retouching is done with the help of mechanics and spray painter. Till hitherto, the best way to get the job done, was using of N.C. Lacquers. But lately, N.C lacquers and thinners are becoming more expensive and therefore all major manufacturers of auto paints have started offering chain stopped quick drying synthetic enamels. As against N.C lacquers, they offer more coverage, better gloss not needing any rubbing or burnishing. They dry slower in comparison to N.C. Lacquers but dust collection is limited, essential when painting is carried out in semi open space. Such a product we offer is known as eurocoat auto finish. Much cheaper thinner can be used and in lower quantity whereby, it helps in controlling pollution.   Areas of Application :By and large, all types of vehicles including luxury buses. But can also be used for painting large and smallengineered articles.   Surface Preparation :Basically, the surface must be primed, puttied, evened with the use of surfacer. Thus, the only care to be taken is the surface must be free from oil or grease spots. They can be solvent wiped to ensure proper adhesion.   Directions for Use : Stir the material in container, thin to required viscosity and start spraying. On smaller articles, wet on wet, threecoats must be applied while for a larger area three coats must be applied at an interval of 24 hours. The gloss obtained requires seeing for believing! After three days, apply a thin coat of wax or silicon polish.   Notes :Please ensure that the painter, whom you have given the job, is an expert spray painter. May be, the fellow is costlier but to get a first class finish, it must. Eurocoat is also available in metallic shades as well as clear. The latter may be mixed with paint, to be used as final coat and in the ratio of 1:1.Never use clear by itself. It will result into faster loss of gloss.

The company has come up as one of the most renowned Manufacturers and Suppliers of Rosalee NC High-Gloss Auto Lacquers & Clear. The Rosalee NC High-Gloss Auto Lacquers & Clear is extensively used in auto refinishing processes and is known for its feat drying. The quality of the Rosalee NC High-Gloss Auto Lacquers & Clear is widely appreciated by the clients across the country. Scope : Nitrocellulose (N.C) lacquers are very fast drying paints used in a big way for auto refinishing. Henry ford started using N.C. Lacquer for painting his ford-t cars (almost eighty years ago) but today vehiclemanufacturers paint their articles with stoving finishes. Thus, currently, N.C. Lacquers are used for re-finishing only. Here also trend is changing. More and more auto sprayers use quick drying synthetic enamels (like eurocoat) because for improving economy or they useexpensive P.U lacquers for longer lasting quality.   Yet in a large country like ours, use of N.C. Auto lacquers continue, because : Most of auto spray painters work in open, whereby the problem of dust collection is usual and N.C. Lacquer film can be easily sanded with rubbing compound, which removes all dust particles adhered while spraying in the open. Over a period (say two years) when the gloss is gone, it can easily be revived using small quantity ofrubbing compound.   There are number of N.C. Auto lacquers. What is the specialty of N.C. Hi-gloss lacquers? One has to learn a little chemistry to understand our answer : N.C. Lacquers are made with a mixture of gun cotton, non-drying coconut oil alkyd, plasticizer, pigments and solvents. There are very standard ratios of raw materials to be used for getting the best quality. Gun cotton is the most expensive and therefore unscrupulous manufacturers use less of gun cotton and more of alkyd. Coconut alkyd is more expensive than dco alkyd and cheaper product can be made with the latter. Blown castor oil is cheaper than dop, which is a standard plasticizer. Again, in place of standard good quality solvents, cheaper solvent like acetone is used to reduce the cost.   Yet, for a layman, it is difficult to understand the difference because they look alike and the difference in quality is realized after nine to twelve months !   Another way of misleading the consumers is, artificially created highviscosity is offered with a claim that a customer can use three litres of thinner with one litre of lacquer thereby claiming four litres of paint out of one litre. This is absolute nonsense because thinner goes into air, leaving only solids on the surface. Thinner more than necessary, will require more coats to get appropriate hiding and extra thinner used, proves waste.   Areas of Application : Any two-wheeler, three wheeler, jeep, sedan car and commercial vehicle like a bus.   Surface Preparation : The surface must be free from oil, grease and rust. Should be well primer with all dents filled up either with N.Cputty or eurofil (polyester putty). Before commencing the use of N.C hi-gloss auto lacquer, the surface must be made thoroughly even with the use of N.C, primer surfacer grey.   Directions for Use : When surface has been thoroughly evened, thin the lacquer to required viscosity and start spraying. Minimum three coats are needed to get desired quality. Each coat must be applied at a minimum interval of four hours. Longer duration between each coat should not cause any problem. When hard dry (minimum o/n, startburnishing with rubbing compound and thereafter wax/silicon polish must be used.   Notes : To achieve the desired level of performance, application instructions must be followed thoroughly. In case of need, the final coat may be applied with lacquer and clear, mixed in the ratio of 1:1 never apply clear by itself, as clear by itself has poorer gloss retention. Also note N.C hi–gloss auto lacquer is totally free from rosin to give long lasting performance.

We are a well-established Manufacturer and Supplier of Rosalee Air Drying Cum Stoving Furniture Enamel. The Rosalee Air Drying Cum Stoving Furniture Enamel is a cost-effective Enamel Paint that offers a better slip and faster drying. The high quality Rosalee Air Drying Cum Stoving Furniture Enamel is delivered on a timely basis. Scope : Furniture enamels are different from normal synthetic enamels, as under : Capability of stoving besides air-drying. Possibility of getting better slip in shorter time. Cheaper than normal first quality synthetic enamels. By and large, application is done by spraying and hence spraying droplets should not bounce back, causing dry spray and rough finish.   Under current situation of electric power in the country, furniture enamels should be capable of air-drying (whenever power fails). They should also be capable of drying under heat (stoving) to prevent dust collection and for getting faster production. Alkyd-melamine stoving enamels are ideal but they do not air dry and are costlier.   Areas of Application : All furniture items made with mild steel like tubular chairs, tables, almirahs, filing cabinets and slotted angles.   Surface Preparation : Oil, grease and rust must be removed before commencing painting. This can best be done by using 7-tank phosphate system or by sand blasting. If for any reason, it is not possible to use either of the above said method, use should be made of rustosan. It must be ensured that no trace of liquid rustosan is left on the surface.   Directions for Use : Clean the surface as directed above. Apply a coat of good quality red oxide primer, preferably air-dry cum stoving type. Sand with 400 paper – wet sanding. When the primer film is dry, apply synthetic putty with circular motion of putty knife and allow drying for at least 4-5 hours. Wet sand the putty film, using a fine paper. Apply one more coat (thin) of primer to prevent absorption of paint by the putty film. Wet sand once again. Apply the final coat of air-drying cum stoving enamel, wet on wet three coats. It can be allowed to air dry or stove at 120oc for 30 minutes.   Notes : Some consumers demand orange peel finish on furniture. The effect can be achieved by using higher pressure and by keeping the enamel viscosity slightly higher.

The company is counted among the prominent Manufacturers and Suppliers of Rosalee Anti Corrosive Enamel. The Rosalee Anti Corrosive Enamel is widely used on furniture made of iron sheets and casting. The company ensures that the best quality Rosalee Anti Corrosive Enamel is offered at the best prices on a timely basis. Scope : Normally, synthetic enamels are applied over anti corrosive primers like redoxide or zinc chromate. Yet, at time, the system lacks performance in respect of fighting corrosion. Anti corrosive enamel was developed to attain much better resistance to corrosion even if a primer is not used underneath. It has incorporation of a very special corrosion resistive pigment in the enamel.   Areas of Application : All articles fabricated from iron sheets or iron castings including wrought iron work.   Surface Preparation : The surface to be painted must be free from oil, grease or rust. Best results can be obtained by using rustosan.Alternatively, the articles are to be sand papered.   Directions for Use : Surface must be prepared according to the instructions under “surface preparation”. Thin down to the required viscosity for brushing or spraying and start painting.   Notes : When stoved at 120oc for 30 minutes, good hardness is achieved with good gloss. However, a little variation in shade will occur when the paint is stoved. In case of white, stoving will result in yellowing of the film.

The company is a well-known Manufacturer and Supplier of Karate Aluminium Paints. The Karate Aluminium Paints, offered by the company, are known for their cost-effective pricing as well as excellent quality. The Karate Aluminium Paints are one of the most effective paints when it comes to the withstanding of the corrosion that occurs in mild steel. The Karate Aluminium Paints are heat and light reflective paints with a wide demand. Scope : Aluminium paint is the most cost-effective coating to withstand corrosion of mild steel. Besides, it is heat and light reflective whereby, the ambient temperature under a roof coated therewith, is lower by 5-7oc. To get the best effect of shiny aluminium, use must be made of fine leafing aluminium paste. Also, the medium used must have the lowest viscosity with highest possible solids and lowest acid value. This is necessary for getting the best leafing value, which provides long lasting brightness.   Karate aluminium paint is made with all the above said characteristics. It is dual pack : medium in a bigger tin and paste into a smaller container. For the sake of convenience, the smaller pack is soldered to the lid of the larger can and the paste can be easily mixed into the medium can. It is necessary to have dual package because the leafing value of aluminium gets lowered if the medium andpaste (aluminium) are combined into one pack.   Areas of Application : All mild steel articles, which need water resistance, can be coated with karate aluminium paint. It can be brushed as well as sprayed. It can safely be used for inside/outside coating of potable water tanks. It is also excellent forcoating mild steel roofing sheets, under which the temperature will be lower by 5-7oc against outer temperature. Surface Preparation : See the pamphlet on surface preparation of metals.   Directions for Use : Prepare the surface as directed earlier. Mix medium and paste thoroughly. Dot not use high-speed mixer because under shear, aluminium flakes loose their leafing capacity. Do not use any thinner because the medium is pretty thin and does not need any further thinning when mixed with paste. Start brushing or spraying.   Notes : If possible, use the mixed paint within 48 hours. Storage for a longer time reduces leafing value and the full brightness gets reduced to some extent.

We are a major Manufacturer and Supplier of Roselle Glass Coating. We offer the best grade Roselle Glass Coating, which is known for its excellent adhesive strength in the glass surfaces. The Roselle Glass Coating is available customized shades and gloss levels and the pricing are highly reasonable as well. Composition : Acrylic modified, non-yellowing, aliphatic isocynate based polyurethane two components coating available in customized shades and gloss levels with excellent adhesion on glass surfaces.   Recommended Applications : There is a growing trend in the glass industry to apply organic coatings to glass articles. Glass coatings offerwide variety of decorative effects such as colors and surface textures, along with the high performance protection benefits. Coating of glass with colored organic materials has significant advantages as any colorsare possible without the use of heavy metal salts which are toxic nature. In addition, there is no need to sort different colored glass materials while recycling since the organic material is simply burnt off, leaving onlywhite glass. A further advantage is that designers have greater scope for using colours and patterns. Rosalee Glass Coating provide benefits as listed below : Excellent adhesion to glass. Ability to modify surface appearance of glass objects i.e., glossy, matt, transparent, opaque, metallic, etc. Easy decoration method i.e., various colored glass samples, acid etching for frosted appearance etc can be matched on the same production line. Excellent resistance to chemicals like household cleaning solutions and industrial solvents. Excellent abrasion and scratch resistance maintains the appearance of the glass. Excellent weather stability   Typical Application Systems and Equipments : As the glass surface is highly smooth and non absorbent, there is not any primer required and painting job can be completed with finish paint only. The surface must be dry and free from dust and other contaminants. It is recommended to clean the surface with solvent and cleaning with cotton before painting. Dust free painting booths are recommended for glass painting.   Note : PU hardener is very sensitive to moisture. Keep the containers tightly closed, each time after use. Normal thinners can ruin the PU finish. Use only Rosalee Thinner 099.   Surface Preparation : Not any special surface preparations are required except the cleanliness of the surface is must beforepainting.   Health and Safety : Polyurethane paints contains free organic isocynate compound. Mixing and handling of this product must be carried out with taking proper safety measures to avoid skin contacts, eye contacts, and inhalation of solvent vapours and mist of the paint spray. The painting must be carried out in a well ventilated spray booths fitted with proper exhaust systems. If painting is to be done on site, care must be taken that along with the spray painter; other people in the nearby area are also protected in the same manner as the painter. Polyurethanepaints if swallowed immediately contact a Doctor.

The company has firmly established itself as a Manufacturer and Supplier of Rosalee NC Putty. The Rosalee NC Putty is best available option in the market for the filling and repairing of the dented mild steel surfaces. The Rosalee NC Putty provides quick drying and is available at the market leading prices. Scope : Any surface, which is dented, needs filling up. The best ways to fill up such dents, three options are available : Use Synthetic Putty : dries late Use N.C. Putty : very quick drying Polyester Putty : Two Pack   The last option is the best dries very fast, can be sanded after 15-20 minutes only. But being a two-pack system, mixing the base and hardener is cumbersome, and it is the costliest. Obviously, the economic choice has to be Rosalee N.C. Putty.   It is made with gun cotton, alkyd, hard resin and plasticizer in combination with suitable extenders and solvents. Each ingredient has to be thoroughly checked to offer a smooth and free flowing paste, which can be easily applied with a putty knife. Besides, the painter should be able to wet sand within half-hour of application to get silk smooth finish. The right quality is Rosalee N.C Putty.   Areas of Application : Any mild steel surface, which is dented. Examples: mild steel sheets used for making steel furniture, any castiron article, which has to be made smooth, and all types of vehicles, which need repainting.   Surface Preparation : The article to be provided must be free from oil, grease and rust. The best way to achieve perfection is to sandblast or adopt 7-tank phosphate system. If for some reason, it is not possible, use rustosan, which removes oil/grease and rust in one operation. Besides, it gives a film of iron-zinc phosphate for better corrosion resistance.   Directions for Use : Prepare the surface as directed above. Take a small quantity of the paste on a putty spatula and start filling dents with semicircular motion of hand. Ensure that putty does not roll back. Since the putty contains about 40% of solvents, which go into air, dents will never get filled up in one operation. Minimum three coats of putty are needed to get a desired result. The putty can be applied wet on wet but it is recommended that a minimum time of half an hour be given between each coat so that pinholes do not develop. Start wet cutting using the finest paper and continue till a silky smooth surface is achieved.   Notes : After using the putty, close the lid of the container very tightly. Otherwise, drying will waste half the quantity.