Filter Units Dealers in Bangalore

We offer a wide variety of membrane filter support glassware for most scientific applications that require vacuum filtration.1. Choose the appropriate support glassware that fits the diameter of the filter membrane you are using (25, 47 or 90mm).2. Choose the appropriate connection for the flask or bottle you will collect the filtrate in.The following information will help you select the most appropriate glassware for your specific application.   FILTER SIZE 25mm Support glassware is designed for filtering small volumes of liquids in particulate or biological contamination studies.47mm Support Glassware is recommended when analyzing up to 500 ml. of liquids for particulate or biological contamination, water/waste water analysis (reference: standards methods for the examination of water and waste water, 18th Edition, 1992), sterility testing of pharmaceuticals by the bacteria retentive filter method (reference: U.S. Pharmacopeia XXIII), and for preparing particulate free or sterile filtrates.90mm Support glassware is recommended for filtering large sample volumes, liquids with a heavy particulate load and viscous liquids when a high flow rate is required. The larger filter area can provide filtration rates up to four times faster than 47 mm assemblies.   SUPPORT STYLE Fritted Glass Supports. Filtration assemblies with fritted glass supports are recommended for general membrane filtration analysis of samples for microbiological or particulate contamination. This support style is recommended when using gridded filters because the glass frit provides the most even distribution of the sample through the filter membrane. All of the fritted glass support bases have a coarse (40-60μm) porosity.   CONNECTION TO FLASK/BOTTLE Silicone Stopper Connections. Silicone or neoprene stoppers are the most common connector from the filtration assembly to a Erlenmeyer style flask and are recommended for most routine filtration studies of aqueous solutions. Stoppers are not recommended when filtering organic or most corrosive solutions or when preparing HPLC mobile phase.Ts 40/35 Glass Joint Connections. Filtration assemblies with Ts 40/38 outer joint connections are recommended when filtering corrosive solutions and organic solvents. This connection style is also recommended when preparing HPLC mobile phase, since the “all-glass” connection eliminates phthalate contamination that can occur when using silicone or neoprene stoppers.47 mm All Glass Filtration Assemblies with GL45 Thread Connection Designed to collect the filtrate directly into a media-type bottle.    

We design, develop and supply Fan filter unit. These units are built as per customer specific requirements. Fan filter units are more suitable where space is a constraint to accommodate conventional duct supply system.

We make sure that the products that we deliver will remain completely damage free as we make use of the quality packaging material and have skilled personnel for the packing of the products. In order to ensure zero defects to the products, we have installed automated warehousing system in our spacious warehouse. The system is supervised by well-trained personnel only.

The filter unit will have PP filter chamber ,PP filter pads and PP / nylon filter cloths on which filter paper is mounted. The filtration capacity are apx 600 to 3000 lph . The unit can filter even below 5 microns particulates, by using suitable filter paper.The filter will have a glandless, magnetically coupled PP /monoblock pump starter, ON - OFF switch. 3M long inlet and outlet hoses with inlet pre- filters are also provided.

• Application: The EZ-Fit(TM) Filtration Units have been designed to ensure optimal microbial recovery.
• Brand Name: Millipore
• Height (100 mL): 66.5 mm (2.6 in.)
• Height (250 mL): 108.5 mm (4.3 in.)
• Largest Diameter: 75.8 mm (3.0 in.)
• Filtration Surface: 12.56 cm2
• Sterilization Method: Blue Units: Ethylene Oxide (EO), Pink Units: e-beam

• Features: Easy accessibility to all the components,Maintenance free operation etc.

In reverse-pulse-jet bag filter unit, individual filter bags are supported by a metal cage spring, which are fastened onto a holding plate at the top of the bag filter unit which separates the unit into two parts as dust chamber and clean air chamber. Dirty gas enters from the bottom of the bag filter unit and flows upwards through the filter bags. The metal cage prevents collapse of the bag. Dust particles filtered and settled at the outer peripheral of the filter tube. Bags are cleaned by a reverse jet of compressed air, injected through nozzle just above the bag holding plate nearer to filter bags. A venturi nozzle provided at the filter bag opening accelerates the compressed air. Since the duration of compressed air jet short time, the filter tube become balloon for short time. This expansion of filter bag for short time of remove the dust cake formation and the dislodged dust falls into a storage hopper below. Reverse-pulse-jet dust collectors can be operated continuously and cleaned without interruption of flow because the burst of compressed air is very small compared with the total volume of dusty air through the collector. Also, the continuous-cleaning feature allows them to operate at higher air-to-cloth ratios, so the space requirements are lower.

Fan Filter Unit, Modular Clean Room, Laminar Air Flow Benches, Work Station

Fan Filter Unit, Chemical Filters, HEPA Filters, Pre Filters

Pepper filter unit