Science Laboratory Equipment Dealers in Dasarahalli, Bangalore

Horizontal Light Path Profile Projectors essentially have the light travelling horizontally (Laterally or sideways) starting from from the source to hit the job on the work-stage and then through the objective to the screen. This is ideal for measuring a wide range of  cylindrical profiles which are excessive long and further other jobs can be measured using fixtures. A few examples for suitable jobs are pump shafts, automotive engine shafts, hollow/solid cylindrical bearing shafts etc.

We are offering horizontal profile projectors salient features: imported lenses are used to minimize the optical aberrations. Square column for better equilibrium of work stage motorized z axis movement for smoother focusing. Highly accurate work stage incorporating needle roller bearings for better life and accuracy linear scales used are of the best international quality for better accuracy and reliability. Hard chrome plated cross table with slots for clamping of accessories laser marked etching on screen for angle and cross hair line, as provided by international companies. Xenon lamp light source for better contrast & life auto sensing mechanism offered along with data processor for better accuracy specifications: screen (mm) 360 projection lens 10 x 20 x 25 x 50 x 100 x field of view (mm) 36 18 14.4 7.2 3.6 mounting of lenses single lens mount or manually indexable turret for any three lenses. contour illumination variable intensity 24v x 150w xenon light source. surface illumination 24v x 150w dual xenon light source with forced ventilated cooling system. magnification accuracy contour : +/- 0.05%, surface : +/- 0.1% focusing centralized needle roller guided hard chrome plated column with a motorized stroke of 100 mm cross table and traverse chrome plated needle roller guided cross tables – 200x200, 320x200, 400x200, 320x160 measurement systems dro / data processor / 2d windows based geometrical measurement software. resolution 0.001 mm angular measurement vernier marking with 2 min. Lc/ digital angular protractor optional.

Optical communication has many advantages over the traditional electrical counterparts. It is insensitive to electromagnetic interference, it offers ground and voltage isolation between the transmitter and the receiver, it provides security from tapping and there will be no sparking at the connecting ends. This trainer uses LEDs in visible range (660 nM) as transmitter, fast PIN-Photodiodes as receiver. A Plastic Optic Fiber (POF) is used as the channel connecting light signal from the transmitter to the receiver. Each of the transmitter and receiver are placed in a PCB mountable plastic housing. A 2.2 mm aperture is provided to hold standard 1000 micron POF. No fiber stripping is required. Microlens is a part of the housing.

Used to generate DC Voltage & Current to charge the 12V Ni-Cd Battery used in HF Radio Hand cranking at 80 rpm generates the required DC Voltage and Current Housed in an Aluminum die cast enclosure Supports enable easy mounting and cranking Carrying case is provided for easily transporting the generator with accessories

• Voltmeter: 0 - 250 V.
• Ammeter: 0 - 15 A
• DIMENSIONS (Nominal): 1.5 m. (L) x 1.0 m. (W). x 0.8 m (D)

IEICOS HEAT PIPE DEMONSTRATION TRAINER is designed with standard industry state-of-the-art components to help the student’s knowledge about currently available products and components. The system is self contained with a full fledged easy access control panel with various meters, displays, switches and indicators.

• Brand Name: Omega
• Features: precise design, high resolution, optimum contrast, accuracy and vibration-free inspection of components
• Diameter: 360mm
• Magnification lenses: 10x or 20x or 25x or 50x or 100x
• Accuracy: 0.05%
• Illumination: 0.15%
• Vertical Movement: 100mm
• Capacity: Approx.15Kgs
• Body Material: Aluminium, Mild Steel
• Usage/Application: Auto Mobile Industry
• Focusing Length: 125 mm
• Cross Table Size: 320 x 160 mm (X Axis),150 x 75 mm (Y Axis)

• Application: Training
• Material: MS
• Rated Power: 1-2 HP
• Motor Speed: 1400-2000 RPM
• Surface Finishing: Color Coated
• Sump: 10-20 Liter Capacity (Approximate) Vane or Gear Type
• Flow: 10-20 LPM at Working Pressure 35-50 Kg/Cm2
• Valve: Direction control

• Specimen (Pin): 8 mm, 10 mm and 12 mm diameter (12 mm long)
• Specimen (Ball): 8 mm, 10 mm and 12 mm diameter
• Specimen (Disc): 54 mm diameter and 15 mm thick
• Stations: 1, 2, 4 or 6 stations
• X Axis: 44 mm (Max stage travel), Max wear track depends on specimen size.
• Y Axis: 44 mm (Max stage travel), Max wear track depends on specimen size.
• Standard Loading Module (each station): Up to 400 N (Motorized, feedback controlled)
• High Load Module (common to all stations): UP to 3000 N (Hydraulic, feedback controlled)

There are roughly one million hip joint and quarter million knee joint replacements every year. With an increasingly aging population around the world, these numbers are only going to increase and therefore, requirements for artificial hip and knee joints will also increase. Because of this demographic change, the challenge of an absolute reduction in wear and tear of artificial joints with minimal or no revised surgery has become more critical than ever. Currently available structural and lubricating materials are unable to reproduce low friction and wear response as observed in naturally occurring joints and lubricants. As a result, some structural biomaterials like UHMWPE or CoCrMo last for 10-12 years (average) whereas the natural joints can last for 60-70 years. There is an increasing need of novel materials to increase life span of the artificial joints. To promote such an environment there is a requirement for rapid testing (friction and wear) of biomaterials in accordance with and beyond the standards, and the BioTribometer serves this role with full compliance with ASTM and ISO standards. The Ducom BioTribometer is widely used for tribological investigation of materials replacing naturally occurring interfaces in joints. Artificial materials can be classified into (1) alloys, composites and ceramics used as structural materials, and (2) synthetic hyaluronic acid and polymer based gels used as boundary and fluid film lubricant materials. Structural materials like UHMWPE, Al2O3, Polycarbonate urethanes (PCU),Ti-6Al-4V are used to replace acetabular cup, femur head, meniscus and tibia (epiphysis), respectively. Lubricant materials like hydrogels based phospholipids and animal derived hyaluronic acids are used as injectable lubricant supplements for knee and hip joints. Development of artificial materials is driven towards performance that is similar to, or better than healthy and natural joints with respect to friction and wear response. Friction and wear performance of these materials can be investigated using standard test methods such as ASTM F732 and ISO 14242, that prescribe motion, load and speed profiles that are relevant to kinematics of hip joints. The Ducom BioTribometer complies with these ASTM and ISO standards. The Ducom BioTribometer has capabilities that extend beyond the scope of standards. This leaves great potential for design of test methods for material characterization as well as compliance with future standards.   Features     Configurable system with single or multiple stations. Conforms to ASTM F732 Mimics sliding speed and load profiles in ISO 14242 Acquisition of friction and linear wear profiles Rated for continuous operations up to 5 million cycles Programmable multi-direction motion common to all stations Elliptical, circular, figure “8”, square (clockwise and counter clockwise) Linear and angular reciprocating Pin or ball materials can be metal, ceramic or polymer and disk of metal, ceramic or polymer among choices of many materials. Independent pin/ball rotation about its own axis for each station (optional) Sliding speeds of up to 0.1 m/s* Independent load control up to 400 N for each station Or, common loading of all stations of up to 3000 N* (optional) Temperatures measurement module (optional) Independent friction force measurement for each station (optional)¤ Independent peristaltic pumps for fluid circulation (optional)* ¤ Not available for all configurations* With appropriate optional equipment selected   Options     Standard Loading Module (per station) High Load Module (common to all stations) Pin Rotation Module (per station) Frictional Force Measurement Module (per station) Wear Measurement Module (per station) Temperature Measurement Module (per station) Preistaltic Fluid Pump (per station) TriboCorrosion Module (per station)

• Country of Origin: Made in India
• Frequency: 50-60 Hz
• Application: Laboratory
• Material: Stainless Steel
• Brand Name: IEICOS
• Power Source: Electric

his trainer uses LEDs in visible range (660 nM) as transmitter, fast PIN-Photodiodes as receiver. A Plastic Optic Fiber (POF) is used as the channel connecting light signal from the transmitter to the receiver. Each of the transmitter and receiver are placed in a PCB mountable plastic housing. A 2.2 mm aperture is provided to hold standard 1000 micron POF. No fiber stripping is required. Microlens is a part of the housing.Sine and triangular signal source with variable frequency and amplitude.A switch to select sine or triangular signal and connect to the transmitting circuit.A variable POT at the transmitter offers the intensity adjustment.A switch is provided to select the Optical receiver to be connected either to the power measurement circuit or to the signal receive and regeneration circuit.Built in 3 12 digit display for measuring optical power in DB.

We offer extensive range of medical equipments like tracheotomy set. Tracheotomy sets are used in medical surgery. These are highly durable medical equipments and user friendly. It is completely hygienic and sterilized and safe to use.

We are one of the famous company, who are manufacturer of mil grade hand crank generato.

HORIZONTAL TYPE PROFILE PROJECTOR WITH 360MM DIA. SCREEN 400 X 200 CROSS TABLE WITH 200 X 100 MM TRAVEL ON X AND Y AXES (FOCUSING AXIS), VERTICAL MOVEMENT 150MM MEASURING AXIS. MEASURING SYSTEM OPTION DRO/DP/PC BASED SOFTWARE.

Vibration Generator, machine tool dynamometer, wind tunnel

Ieicos temperature process control system is an advanced experimental bench designed for study and understanding of temperature control process, components involved in monitoring and control of temperature, stability and time constant of temperature control etc. In a table top size for easy handling and setup. Designed to take very little of valuable lab space, it is designed to provide utmost features with little components at low cost. The temperature process control trainer can be used to study onoff control, proportional (p), proportional-integral (pi), proportional-integral-derivative (pid) operation, tuning of controller in open loop and closed loop, auto-tuning and stability.

biotech equipments, Bellow, Stainless Steel Fabrication

Medical Equipments, uro bag, hospital disposables, romo jet syringe

machanical engineering equipment, gear cutting, gear cutting machines

process recorder, Proximity Sensors, sterilizers, Stripping Machine

mechanical testing equipment, Testing Equipment

Cement, Concrete, Construction Testing Equipment, sand soil

environmental simulations equipments, laboratory item, hot chamber

Medical Equipments, Dental Equipments

Medical Equipments, display signage, sheet metal racks, sheet metal pallet

Liquid Flow Meter, analytical system, nir analyser, water purification system

Industrial Equipment

Mechanical Equipment

Profile Projectors, video vision systems

chemical testing tubes, markers

Medical Equipments, Nebulizer, Pulse Oximeter, Bipap, Portable Ventilator