Solar Water System Dealers in Dinnur, Bangalore (4 products available)

The FLAT PLATE collector absorbs the solar energy and converts it into heat energy. The cold water flowing through the riser pipes gets heated and moves into insulated storage tank through header pipe, due to low density of hot water it occupies the upper portion of the insulated storage tank and the cycle continues as long as the sun rays fall on the collector. By the end of the day the entire tank is with hot water. As the storage tank is insulated which retains heat overnight. In this principle water can reach temperature up to 600c – 850c.   Specifications:   COLLECTOR BOX Collector Size : 2030 x 1030 x 100 mm Collector Box : Extruded Aluminium, make – Indal / Jindal Grade – HE9T/HE9WP Finish : powder Coating Glass Retaining Angle : Extruded Aluminium as above Back Sheet : 22SWG, Aluminium, Revited and sealed with silicone sealed/ Galvanized sheet as per IS Glass : 4mm, toughened, low Iron content with 85% minimum transmitivity Glass/beeding/Sealing : EPDM with 35% rubber content along with the top Aluminium retainer angle, using SS self tapping Screws Grommets : EPDM with Inside / outside locking collar Ends Connections : 4mm thick brass flages with EPDM gaskets Insulations : 48kg/ cu.m density rockwool/ puff Bottom – 50mm and Sides – 25mm Reflective Foll : Aluminium – 100 microns for sides, 50 microns for bottom Frame Corners : Sealed from inside with Silicone Sealant and Provision of Corner Clips for better aesthetics and prevantion of moisture entry  ABSORBER Coating: Selective Bonding between Fins and Riser: Block Chrome – NALSUN Absorptivity > 0.95 Emmissivity : < 0.15 Ultrasonic Welding / Lead and Tin Soldering Bonding btw Header and Riser : Metallurgical bonding using 14% Silver Brazing rod Absorber Area : 2.07 sq.m Fins : 99.9% + -0.01 Copper – 120 mm wide, 36 SWG Number of Fins : 09 (Nine) Test Pressure : 5.0 kg/sq.cm Header : 99.9% + -0.01 Copper -1” x22 SWG Riser : 99.9% + -0.01 Copper-1/2 x22 SWG System Temperature : 60o C - 85oC  STORAGE TANK Inner Storage Tank : SS 304 Grade with TIG Welding Inter Connecting Pipes : SS 304 Grade End covers : Powder Coated pressed Aluminium dishes Insulation : 100 mm Rinsine bonded Rockwool Tank Outer Cladding : SS mirror finishing/ Powder Coated Aluminium with optional Colours   Features:   ISI marked 1.5 KW back-up heater with Thermostat(optional) All fasteners are made of SUS 304 Food grade for rust free. No scaling formation will be occurred by using salt and hard water in ETC systems. Compressed PUF, insulated storage tank to retain the hot water for more than 48 hours. Auxillary tank is fitted instead of air vent, withstands high cold water pressure also minimize mixing of hot water and cold Strong, polyester powder coated, rust free metal frame and laminated outer tank. Air tight silicon 0 Rings avoid hot water leakage due to high temperature. High quality, tested and tough/ borosilicate glass tubes. Easy Maintenance & round the clock service facility with Dealer network and service centers all over India (Goa, Karnataka, Andra Pradesh, Tamil Nadu, Maharashtra - Kolapur, Jaipur).

A solar-powered pump is a stand-alone system running on electricity generated by photovoltaic panels available from collected sunlight as opposed to grid electricity or diesel run water pumps. The power generated from the Solar Photovoltaic Modules are used to operate the submersible e/surface pump for lifting water from different sources such as open well, tube well, reservoir or river etc,.The operation of solar powered pumps is more economical mainly due to the lower operation and maintenance costs and has less environmental impact than pumps powered by an internal combustion engine (ICE). Solar pumps are useful where grid electricity is unavailable and using alternative sources (in particular diesel powered motor/pumps) is very expensive.