srinivasa products Rajajinagar, Bangalore, Karnataka

Water softeners contain high capacity strong acidic caution exchanger in bead form. It is used in sodium form to remove hardness due to Ca & Mg ions. During Service Period:-    RSO3Na + CaCl2 = (R.SO3)2Ca + 2 NaCl    RSO3Na + MgCl2 = (R.SO3)2Mg + 2 NaClThus calcium & magnesium hardness is removed & replaced with more soluble sodium ions in form of sodium chloride. When this soft water is fed into distillation unit, scale formation is reduced drastically & sodium chloride starts to settle at the bottom of boiler over a period of time. This can be easily removed by using concentrated hydrochloric acid.The softener has been recharged once in two months depending upon the hardness of water at customers place. To recharge 10-15% sodium chloride solution is used & passed through the softener. This unit is not recommended for where there is very high TDS of more than 600 PPM.Regeneration (R.SO3)2Ca + 2 NaCl = R.SO3Na + CaCl2Note:- When raw water is fed to distillation unit. Calcium & magnesium carbonates & chlorides (Hardness) settle in the boiler. This hardness does not get dissolved even when heated with HCL or HNO3. Hence, a water softener is used.Water softener can be used only where total hardness of water is less than 400 PPM. TDS of water does not reduce/change by using water softener.The hardness test is performed as follows:- Take 25 ml of water Add 5 drops of ammonia buffer solution. Shake it & then add a pinch (2 crystals) of Erichrome black T- Indicator. The Colour turns red. (In Case the colour turns blue at this stage only it means zero PPM hardness). Now add drop by drop N/50 EDTA Solution until the colour turns blue. Each drop is 2ppm of hardness. Note:- Use the softener, perform the test & see the result. The hardness should be between 0-50ppm. In case the softener has not been used for some time or has been kept idle, charge the Softener using Sodium Chloride solution & then perform the test. The white colour deposits which forms is due to precipitation of sodium chloride upon heating & not due to calcium.   How to Regenerate a Water Softener:- Perform the hardness test if your water is showing more than 300ppm even after using softener, then it means you need to recharge it. Follow the steps mentioned below:-. Disconnect the inlet & outlet rubber tubing. Prepare Sodium chloride solution by adding approximate 200 grams Sodium chloride to 20 liters distilled or de-ionized water. Pass the sodium chloride solution through the softener inlet drop by drop. The outlet can be left to the sink. The solution should pass through the softener for period of 45 minutes. Rinse it with de-ionized water & it is ready for use once again. 

Silicone tubing is the softest and most flexible tubing. It is translucent white. Unlike vinyl tubing, there is no plasticizer dissolved in the tubing material. The tubing is pure polymerized silicones with nothing to leach out. This makes silicone tubing suitable for use with most solvents, especially when used at room temperature and with short (< 24 hr) contact periods. Temperature range – 60 degree C to +200 degree C, odourless, tasteless, inert, resilient, stretchable and resistant to compression set, good electrical and weather ability properties, resists U.V, Ozone, gases and moisture. It`s Applications is peristaltic pumps, hot water feeds, laboratory, food service, beverage service. Silicone rubber tubing sizes start from 0.2mm ID up to 50mm OD and can be supplied in quantities of 10meter.

Silicone tubing is the softest and most flexible tubing.It is translucent white. Unlike vinyl tubing, there is no plasticizer dissolved in the tubing material.The tubing is pure polymerized silicones with nothing to leach out. This makes silicone tubing suitable for use with most solvents, especially when used at room temperature and with short (< 24 hr) contact periods.Temperature range – 60 degree C to +200 degree C, odourless, tasteless, inert, resilient, stretchable and resistant to compression set, good electrical and weather ability properties, resists U.V, Ozone, gases and moisture. It`s Applications is peristaltic pumps, hot water feeds, laboratory, food service, beverage service.Silicone rubber tubing sizes start from 0.2mm ID up to 50mm OD and can be supplied in quantities of 10meter.   The silicon septa is a high quality rubber septa designed with serrated bottom for sealing open-top glass vessels as well as standard taper joints. Ideal for moisture or air sensitive applications.These Septas have serrated sealing capability to the inside of the vessel, as well as the turn-over top seal. Autoclave able and packaged in white-room conditions.   SIZES : 1. 14/23 2. 19/263. 24/294. 29/32

Fused quartz wool has the same properties as pure quartz glass. The fibres are non-flammable and incombustible. The fibres maintain their usable mechanical properties up to 1050°C. High purity quartz wool is used for filtration and insulation in environments where the properties of high purity quartz are needed.These fibres, wools, and fillers have a high temperature resistance, are immune to corrosion and have high electrical resistivity, making them ideal for fillers and insulators in electronics, insulators in space craft and high tech airplanes, high temperature filtration, insulators for very hot or very corrosive environments and as an asbestos replacement.It is available in 10gm and 100gm packing.   The quartz ground joints are manufactured from quartz tubing and careful attention is paid to the accuracy of form, uniformity of surface finish, profile and taper to reduce the possibility of leakage and joint ‘seizure’. The outer joints have extra glass tooled onto rims to add to chip resistance.   SOCKETS: Interchangeable joint Sizes10/19, 12/21, 14/23, 19/26, 24/29, 29/32, 34/35, 40/38, 45/40, 50/42, 55/40, 60/65, 70/75   CONES: Interchangeable joint Sizes10/19, 12/21, 14/23, 19/26, 24/29, 29/32, 34/35, 40/38, 45/40, 50/42, 55/40, 60/65, 70/75

Silica dip tubes are also used as dipping tubes to protect thermocouples in molten metal temperature measurement, and as pin sampling tubes for molten metal analysis.

SRINIVASA PRODUCTS offers a variety of grinding and polishing services for wide range of sizes, shapes and grades of quartz and borosilicate glasses. Our machine capabilities include: 1. Ground and polished discs upto 150 mm with varying thickness. 2. Ground and polished plates upto 250 mm x 250 mm with varying thickness.

FUSED QUARTZ DISCS & PLATES SRINIVASA PRODUCTS offers a variety of grinding and polishing services for wide range of sizes, shapes and grades of quartz and borosilicate glasses. Our machine capabilities include:1. Ground and polished discs upto 150 mm with varying thickness.2. Ground and polished plates upto 250 mm x 250 mm with varying thickness.

The unit consist of a primary boiler with built-in heater. The primary boiler has a ‘O’ ring groove at the top, on which a silicone ‘O’ ring sits. The secondary boiler with condenser is mounted on the primary boiler. A double wall condenser ensures separate condensation of vapor coming from the two boilers using a single cooling circuit. The whole unit is mounted on powder coated stand with electrical terminals for easy connection either to the mains or DAPS (Distillation Apparatus Power Supply) The bottom outlet is connected to a ‘T’ joint of which one limb is connected by a rubber tubing & pinch cock for cleaning sediments in primary boiler by acid wash and other limb to the water leveller of ‘DAPS’.

The Kjeldahl method is the official method for determining nitrogen and protein contents in : Foods (Raw materials and finished products) Animal feeds Soils, Fertilizers, etc. Waste water, sludge, etc. Lubricants, fuel oils, etc   KJELDAHL METHOD: Johan Kjeldahl a Danish chemist in 1883 while studying the changes of protein content during the transformation of barley into malt process developed the method for determining Nitrogen which then took its name from him. Because of its high degree of precision, reproducibility and versatility, the Kjeldahl method is used today to determine content of Nitrogen and proteins according to official methods. (AOAC, EPA, DIN, ISO).Seldom in human history has an invention remained basically unchanged for such a long time as Kjeldahl's method for Nitrogen determination.More than 90% of protein containing samples and over 60% of all Nitrogen containing samples can be analyzed by using this basic procedure.The food industry processes raw material in numerous ways and into many different products from cheese and bakery products or ice cream production through to uses in meat processing or in the production of ready meals. Hence the overall protein content plays an important role both for the payment of raw material delivered and for determining the value of the product.The digestion units are compact and well insulated to minimize heat transfer to the surroundings and allow fast, even heating thus giving good working conditions as well as saving energy.

DescriptionDescription ID x OD (mm) ID x OD (mm) 1 x 3 34 x 38 2.35 x 4.35 35 x 38 3 x 5 35 x 40 4 x 6 37 x 40 5 x 7 40 x 45 6 x 8 41 x 46 7 x 9 45 x 50 8 x 10 50 x 55 8 x 11 55 x 59 8 x 12 55 x 60 9 x 11 60 x 65 9 x 12 65 x 70 10 x 12 70 x 75 12 x 15 75 x 80 15 x 18 80 x 85 16 x 19 85 x 90 17 x 20 90 x 95 18 x 20.5 95 x 100 18 x 21 100 x 105 19.7 x 22.3 105 x 110 20 x 23 110 x 115 21 x 24 115 x 120 22 x 24 125 x 130 22 x 25 132 x 140 25 x 28 146 x 151 27 x 30 170 x 176 30 x 33 193 x 200 32 x 35  

We offer a wide variety of membrane filter support glassware for most scientific applications that require vacuum filtration.1. Choose the appropriate support glassware that fits the diameter of the filter membrane you are using (25, 47 or 90mm).2. Choose the appropriate connection for the flask or bottle you will collect the filtrate in.The following information will help you select the most appropriate glassware for your specific application.   FILTER SIZE 25mm Support glassware is designed for filtering small volumes of liquids in particulate or biological contamination studies.47mm Support Glassware is recommended when analyzing up to 500 ml. of liquids for particulate or biological contamination, water/waste water analysis (reference: standards methods for the examination of water and waste water, 18th Edition, 1992), sterility testing of pharmaceuticals by the bacteria retentive filter method (reference: U.S. Pharmacopeia XXIII), and for preparing particulate free or sterile filtrates.90mm Support glassware is recommended for filtering large sample volumes, liquids with a heavy particulate load and viscous liquids when a high flow rate is required. The larger filter area can provide filtration rates up to four times faster than 47 mm assemblies.   SUPPORT STYLE Fritted Glass Supports. Filtration assemblies with fritted glass supports are recommended for general membrane filtration analysis of samples for microbiological or particulate contamination. This support style is recommended when using gridded filters because the glass frit provides the most even distribution of the sample through the filter membrane. All of the fritted glass support bases have a coarse (40-60μm) porosity.   CONNECTION TO FLASK/BOTTLE Silicone Stopper Connections. Silicone or neoprene stoppers are the most common connector from the filtration assembly to a Erlenmeyer style flask and are recommended for most routine filtration studies of aqueous solutions. Stoppers are not recommended when filtering organic or most corrosive solutions or when preparing HPLC mobile phase.Ts 40/35 Glass Joint Connections. Filtration assemblies with Ts 40/38 outer joint connections are recommended when filtering corrosive solutions and organic solvents. This connection style is also recommended when preparing HPLC mobile phase, since the “all-glass” connection eliminates phthalate contamination that can occur when using silicone or neoprene stoppers.47 mm All Glass Filtration Assemblies with GL45 Thread Connection Designed to collect the filtrate directly into a media-type bottle.    

We deals in double distillation unit In view of calcium & magnesium deposits occurring in primary boiler and the difficulty involved in cleaning these deposits, made us to think of designing the apparatus, so that the primary boiler could be easily dismantled for easy cleaning of calcium & magnesium deposits.

A supply of pyrogen free distilled water is basic requisite for many research, analytical & industrial laboratories. Moreover, the materials of the distillation apparatus and storage vessels, should be chosen so as to avoid diffusion of contamination into the distillate. Quartz distillation units are manufactured from imported fused quartz tubes. The exceptionally high chemical purity and very low solubility of this material enables the production of very high performance system. The greatest possible attention has been taken for technical performance, simplicity of use and efficiency.

VITSIL glass distillation units continue to be the most effective, economic method of producing ultra pure water for laboratory use.By contrast de-ioniser are only effective in removing those substances which are ionized. Further the resins contribute organic impurities to water and an ideal environment for bacterial growth in course of time.These distillation units are designed to produce a distillate of consistent purity. The unit consists of horizontal borosilicate boilers, condensers and quartz heater. All parts are replaceable.   INNOVATIVE DESIGN The newly developed quartz heater is advantageous than chromium plated heaters used by other manufacturers. Chromium plated heaters react with acids during cleaning process.Quartz heaters do not react with acids or water during cleaning or at elevated temperature unlike metallic ones. Quartz heaters are easy to assemble and dismantle, unlike metallic ones which are bulky.   ADVANTAGES Compact, simple to use. Economical and ideal for colleges and general laboratory use. Powder coated stand for rust free operation. Provision for easy cleaning of boiler.

The COD Digestion Unit is used for determination of Chemical Oxygen Demand in effluents. The unit consists of:a) Aluminum block heating unit with provision to keep 8or 15 samples at a time in 40 mm diameter reaction vessels.b) Air Condensers.c) Digital PID temperature indicator cum controller with built in timer for temperatures up to 250 Celsius.d) Insert rack to hold the digestion tube with air condenser.    MODEL: a) 8 samples COD System - b) 15 samples COD System  SPARES: 1) COD digestion vessel in borosilicate glass 2) Air condenser in borosilicate glass

Aqua therm heat exchanger can be used with distillation units. The hot water released from the Condenser outlet is usually let into the Sink, thereby wasting precious water.However, Aqua therm heat exchanger is equipped with cooling coils and fan that cool the hot water as it comes out and then pump it back into the Condenser inlet, thus saving water.   ADVANTAGES It can be mounted on a table to occupy less space. The power consumption is minimal. It takes only 15 liters of water to run the distillation unit(single or double).

 supply of pyrogen free distilled water is basic requisite for many research, analytical & industrial laboratories. Moreover, the materials of the distillation apparatus and storage vessels, should be chosen so as to avoid diffusion of contamination into the distillate.Quartz distillation units are manufactured from imported fused quartz tubes. The exceptionally high chemical purity and very low solubility of this material enables the production of very high performance system. The greatest possible attention has been taken for technical performance, simplicity of use and efficiency.   DESCRIPTION OF APPARATUS The unit consist of a primary boiler with built-in heater.The primary boiler has a ‘O’ ring groove at the top, on which a silicone ‘O’ ring sits. The secondary boiler with condenser is mounted on the primary boiler.A double wall condenser ensures separate condensation of vapor coming from the two boilers using a single cooling circuit.The whole unit is mounted on powder coated stand with electrical terminals for easy connection either to the mains or DAPS (Distillation Apparatus Power Supply) The bottom outlet is connected to a ‘T’ joint of which one limb is connected by a rubber tubing & pinch cock for cleaning sediments in primary boiler by acid wash and other limb to the water leveller of ‘DAPS’.    DEMOUNTABLE MODEL In view of calcium & magnesium deposits occurring in primary boiler and the difficulty involved in cleaning these deposits, made us to think of designing the apparatus, so that the primary boiler could be easily dismantled for easy cleaning of calcium & magnesium deposits. Spare bottom boilers are available normally from ready stocks.   NNOVATIVE DESIGN The primary boiler is being provided with a ‘O’ ring which acts as a cushion on which secondary boiler and condenser unit is mounted.    DEMERITS IN OTHER BRANDS OF DISTILLERS The distillers available in the market provide either glass flange with clamps or glass ball and socket connection. Glass connections are liable for breakages. The calcium & magnesium deposit forms around the ball joint, thereby, freezing the unit. The steam leaking at ball joint is a very common feature in other brands.Silicone rubber boot & fiber glass insulated electrical connections withstand higher temperature and long lasting as compared to rubber boot & PVC insulated wire provided by other manufacturers.    

Color : Light White

Voltage : 220V

Condition : New

Capacity : 20L/Hr

Power : 0-5kw

Driven Type : Electric

Warranty : 1yrs

Automation Grade : Automatic

Country of Origin : India

Brand Name : Vitsil

Classification : Scientific

Color : Navy