Test Rig Dealers in Peenya Industrial Area, Bangalore

Spindles are tested as per DIN 8637 Standards for Temperature, Vibration at maximum speed. Condition monitoring will be undertaken on specific request.

• Dimensions: 2m W x 2.5m L x 1.5m H (Nominal)

Loading Arrangement: Eddy Current Dynamometer of suitable size as per engine power rating provided with eddy current controller with digital displays for excitation voltage and current.Air Flow Measurement: Powder Coated box with orifice type flow meter with Digital manometer Range 0 – 1000mm WC Fuel Flow Measurement: Powder Coated fuel tank (capacity 15 lts) with glass metering column and scale along with digital manometer Range 0 – 1000mm WC.

The test facility with Re-Configurable system (T-Slot Bed, Linear Actuators on brackets) is used to conduct performance test, Static Strength Test, Fatigue Strength Test on the UUT. Servo Actuators of 50 KN Built In Position Sensor Easily Configurable Tests Low Noise Hydraulics Frequency Offset Number of Cycles On Line Force Sensor Calibration Loading Actuator : ± 50 KN ( 02 Nos ) Stroke : ± 100mm Force Sensor : 50 KN Position Sensor : ± 100mm Mechanical : T Slot Bed , Brackets + Fixtures T-Slot Bed Size : 3.00 Mtrs X 2.00 Mtrs

• Place of Origin: India

Automatic selection of the flow, pressure and speed on selection of the model Security (multiple level) to allow access, based on user levels Configuration of sensors and online calibration of sensors Specifications   Drive Motor Max Speed: 500-800 RPM Pump Supply Max Pressure: Max 200 Bar Pump Supply Oil Temperature: Ambient to 120deg C Shaft Load (Belt Load): Max 200kg Hot Chamber Temp. Control: Room Temp. to 100deg C (Optional) Drive Torque: Max 25Nm Pump Supply Max Flow: Max 25 LPM Pulley Ratio: 1:3.1 Test Configuration Possible: Diret Drive - Pulley Gear Mesh Drive

THIS TEST BENCH IS DESIGNED AND DEVELOPED ACCORDING TO IEC-60947-1 FOR ENDURANCE OF THE MCCB,MCB SWITCH GEARS PRODUCTS.WE HAVE USED PNEUMATICS AND ELECTRONIC COMPONENTS IN CAPTURING THE DESIRED PARAMETERS.THIS TEST BENCH CONSITS OF THREE STATIONS AND CAPABLE OF MEASURING THE THREE SAME DIFFERENT DEVICES .

The journal bearing test rig for investigating the distribution of pressure in slide bearings the principal of hydrodynamic lubrication. The distribution of pressure & the carrying capacity can be determined on a sliding bearing model at different bearing loads & speeds. Learning objectives/experiments Relocation of the shaft journals in relation to speed Pressure distribution in the bearing with constant load and at various speeds Critical speed in relation to load Critical speed & viscosity in relation to oil temperature Category: Test Rig

• Brand Name: CHP-RIG

We manufacture custom built automated hydraulic test rig for testing hydraulic components like cylinders,pumps,valve etc., with plcscada systems.

• Type: Test Rig
• Certification: CE Certified
• Weight: 100-400kg
• Voltage: 110V, 220V, 380V
• Condition: New
• Application: Industrial Use
• Power: 3-5kw, 5-7kw
• Driven Type: Electric
• Motor Power: 2hp
• Automation Grade: Automatic

• Material: Stainless Steel
• Weight: 5+0. 2 - 0. 0 kg
• Voltage: 220 V
• Power Source: Electric
• Frequency: 50-60 Hz
• Shaft Length: 4 m

• Frequency: 1 to 50 Hz
• Stroke: 1 mm (fixed)
• Load: up to 1.0 kg
• Temperature: Ambient to 150 Deg C. Optional "High Temperature Module" for ambient to 400 Deg C
• Upper specimen: 6 mm (dia) - ball
• Lower specimen: 10 mm (diameter) X 3 mm (thick) - disc

The purpose of this tester is to characterize friction under lubricated condition using a ball on disc configuration. This tester is particularly suited for evaluating low lubricity fluids like diesel and gasoline. The system consists of a temperature controlled stage that houses the test plate. A reciprocating arm with a ball holder to hold the test ball is pressed against the test plate with a known force. The system reciprocates maintaining the required stroke length, frequency, load, temperature and humidity. A piezoelectric force transducer senses the frictional force. The unit is computer controlled and uses the WinDucom Data Acquisition System to record the output parameters.   Features     Compact bench-top design. Includes environment chamber and humidity probe. Includes ambient temperature and relative humidity probe. Especially suited for wear tests of diesel fuels, additives and lubricants. Pre-programmed CEC, ASTM and ISO test procedures for automated operation. Computer controlled operation with software license included. Includes CompariView module for comparative viewing of test results. Options     Humidity ControllerElectrical Contact Resistance (ECR) ModuleTribo-Corrosion CellHigh Temperature Module (Ambient to 400 Deg C)

Tools & Cutters Automatic Back Spot Facing Tool, Rear Counter Bore Tool Automatic Duplex Deburring & Chamfering Tool Counterbore Tool Combo Counterbore Drills Fly Cutter Plate Edge Milling, Plate Bevelling Machine H BEAM, I BEAM MILLING, DRILLING & TAPPING MACHINE Plano Miller, Duplex, Floor Type Multi Angle Universal Milling Attachment Right Angle Milling Attachments Converted Plano Millers Planomilling Conversion Kit

A headform with its crown vertically facing down is fixed to the drop assembly so that using a ball-joint is provided to mount the helmet for test. The headform can be rotated about the central ball-joint provided in the drops assembly to present the required test areas of the helmet to the rigid anvil. A DEBEL provided triaxial accelerometer is mounted at the centre of gravity of the ball-joint.

We offer fatigue test rigs for auto-components like ball joints, steering gears, steering columns, hose pipes, propeller shafts.

We are offering a wide range of compressor test rigs from india.

Air Conditioning Test Rig, Carter Carburetor, Battery Ignition System

simulators, servo actuators, dc servo controllers

Hydraulic Valve Test Rig, hydraulic honing machine, Vertical Honing Machine

test rig, Material Handling Equipments, radial stacker custom built machines

Electrical Control Panels, Special Purpose Machines