Brine Chiller Dealers

• Voltage: 380V-3N-50HZ
• Condition: New
• Warranty: 1 Year
• Power: 1.1 KW
• Air Volume: 12000m3/h
• Dimension: 2200*1100*1600mm
• Voltage:: 400 V / 50 Hz / 3 Ph
• Capacity: 3000 Kcal/Hr to 150000 Kcal/Hr
• Use: Industrial

For low temperature applications where the operating temperature may go below 4°C, Brine solution is used as heat transpiring media. For such applications DAI CHI offers brine chillers to suite the applications.

• Power: 3.5 kW
• Voltage: 440 V
• Country of Origin: Made in India
• Tonnage: 12 Ton
• Brand: Ozone
• Model Name/Number: OAS180TAC
• Compressor Type: Scroll

• Brand Name: VAMM
• Low Power Consumption: Consistency in Temp.

Many Industrial Systems & Processes require Lower Temperature Conditions with Secondary Fluid at lower temperature than required for process having much lower Freezing Point. Normally such Secondary fluids are well known as Brine. Brine is usually a mixture of Common salt and water having freezing point lower than zero. Later the brine solution has been replaced with other solutions such as Mono-Ethylene Glycol, Poly-Propylene Glycol, Calcium Chloride Solution and many more., having better advantages of Thermo-Physical Properties as Low Freezing Point, Lower Corrosion, Better Thermal Conductivity & Specific Heat etc. Using such solutions in different proportions the temperatures of 0 deg. Cent. To -45 deg. Cent. Can be achieved easily a. Applications i. Pharmaceutical Process ii. Chemical Industry iii. Herbal Extraction Plants iv. Soap Manufacturing v. Various Laboratory Procedures vi. Research & Development Departments Institutes vii. Food Industry viii. Beverage Manufacturing ix. Textile Industry & Many More…. B. Refrigeration System – i. Chillers Used for Low Temperature Applications uses Freon Based Vapor Compression Refrigeration Cycle with a variety of Refrigerants viz. A. R-404A B. R-134A C. R-22 D. R-11…etc. Ii. Compressors – Low Temperature Chillers Uses different Compressors depending on the Temperature Requirement & the Type of Heat Load A. Hermetic Reciprocating B. Scroll C. Semi-Hermetic Reciprocating Screw D. Semi-Hermetic Single Two Stage E. Open Type Single Two Stage iii. Condenser A. Air Cooled B. Water Cooled iv. Evaporator A. Shell & tube B. Plate Heat Exchanger

Range: 11, 26, 39, 52 and 85 TR Pre-wired, fully charged and run-tested, ready-to-fit chillers, which take less time to install and start up Reliable and highly energy-efficient scroll compressors Intelligent microprocessor control with digital setting of temperature levels for optimal cooling and power saving Auto-distribution of load for efficient running of the chiller Capacity modulation ensures that only required number of compressors operate to handle the load, thus saving power Lower electrical infrastructure costs In-built anti-freeze protection ensures cut-off before freezing point for reduced breakdowns User-friendly remote control operation for convenience, and remote emergency control in case of fault

MCS Offers Brine Chillers for application demanding temperatures ranging from + 6 to C to -65 o C. Our Brine Chillers are unbelievably compact and modern. The Use of hermetically sealed compressor form Emerson Danfoss Maneurop have made our chiller packages highly energy efficient.

CHOICE OF SCREW COMPRESSOR of Hanbell (Taiwan), Bitzer (Germany) & J&E Hall (UK). All options are semi-hermetic in construction, thereby making it maintenance friendly. The screw compressor range offered is specifically developed for low temperature chillers applications and is offered along with adjustable volume ratio. Besides internally built oil separation system, check valves at suction and discharge port are provided as standard part of the OEM equipment. The screw compressor range offered is specifically designed by the respective OEMs for low temperature applications. HIGH COP/EER High cop/eer as an issue proficient gathering of the refrigerant. These water cooled chiller units are intended to meet the relevant necessities of ASHRAE/ANSI 15 Safety Code. Since the condensers are liberally oversized, productive gathering of the refrigerant prompts lower IKW contrasted and other accessible brands. SHELL & TUBE EVAPORATOR Shell & tube evaporator is constructed with copper containers of 19 SWG that empowers them to withstand hard water with PH more noteworthy than 8. The copper tubes contain Flamingo licensed star turbulator embeds that give turbulence to the refrigerant coursing through the copper tubes. As an issue of this turbulence these Shell & Tube evaporators have amazingly effective hotness exchange rate. The shell is produced from high-review steel. The evaporator is planned according to ASME Section VIII Div.1. AVAILABLE IN A CHOICE OF REFRIGERANTS Available in a choice of refrigerants R-22 (Freon), R-407c and R-134a. Both R-407c and R-134a are environment neighborly and non-ozone draining refrigerants. ULTRA EFFICIENT CONDENSING Ultra efficient condensing using outer finned copper tubes for increasing heat transfer surface results in higher efficiencyin comparison to copper tubes without finning. The copper tubes are of 16 SWG and are finned on the outer surface to accommodate up to 26 fins per inch. The copper tubes are mechanically expanded through a torque controlled machine on the tube sheets that are manufactured on imported VMC machine. ECONOMIZER FOR HIGHER EFFICIENCY Economizer for higher efficiency is provided as per refrigerant used and depending upon the liquid temperature range desired. Economiser is provided as standard part of supply in process chillers opted for evaporating temperature of 0 deg. C or lower. The economizer/sub-cooler enhances the overall capacity of the chiller by 10%, and reduces the power consumption, thereby increasing the overall Coefficient of Performance (COP). AVAILABLE IN A CHOICE OF REFRIGERANTS Available in a choice of refrigerants R-22 (Freon), R-407C and R-134a. Both R-407C and R-134A are environment friendly and non-ozone depleting refrigerants.   ADDITONAL AIR COOLED TYPE OIL COOLER Additonal air cooled type oil cooler is added depending upon the refrigerant used and the chilled water/brine temperature desired. The oil cooler helps maintain the oil temperatures flowing through the compressor within safe limits. The oil cooler fan is automatically controlled depending upon the oil temperature. This feature enhances the screw compressor life. LIQUID INJECTION Liquid injection is a standard gimmick and is utilized to cool the compressor engine slowing down. When the release temperature surpasses the ordinary range, an electric solenoid curl infuses fluid refrigerant to keep the slowing down inside protected breaking points. This peculiarity upgrades the life of the screw compressor. THERMOSTATIC EXPANSION VALVE Thermostatic expansion valve is given as an issue some piece of the water cooled screw chiller gear. Electronic extension valve can likewise be alternatively given. CONTROL PANEL Control panel with IP-65 assurance is given as standard piece of the water cooled supplies. MICROPROCESSOR BASED CONTROLLER Microprocessor based controller is a standard piece of the water cooled screw chiller supplies. The controller permits various set focuses that can be arranged to specific set of values that may be considered inside the safe working extent. If there should be an occurrence of any rupture in any of the set point esteem the controller will excursion the chiller after the fed wellbeing postponement period has passed and show it on the LCD show. Additionally, the controller naturally conforms the limit in a stepped configuration making them perfect for variable burden applications.

• Feature: Effective, High demand, Easy to use
• Condition: New
• Warranty: 6 Months
• Performance: Optimum
• Maintenance: Low
• Finish: Polished
• Resistivity: Corrosion & Chemical resistant
• Usage: Industrial
• Durability: Long Life

• Certification: CE Certified
• Application: Industrial
• Weight: 100-1000kg
• Feature: Durable, Easy To Use, Effective
• Voltage: 110V
• Finishing: Polished
• Power: 1-3kw
• Country of Origin: India
• Brand Name: JE

Scan air manufactured online, recirculated water chillers for various applications as detailed given below. Water chillers for applications ranging from 1° C - 25° C ° ± 1° C specially for soft drink industry online chiller with Stainless Steel 316 grade secondary heat exchanger. The chillers are designed new generation styled and built esthetically to match the modern trend in equipment manufacturing. Standard flow is a portable water chiller with the tank. They are used in closed loop cooling applications. Where all of the water pumped from the chiller returns to the machines under generated by the chiller pump. Reversed flow is a portable water chiller without the tank. It is used in open loop cooling applications where an external tank or through is used. This tank are through must gravity feed into the chiller pump. Which sense water through the chiller and filter, back to the process or back to the tank or through.

• Country of Origin: India
• Certification: CE Certified, ISO 9001:2008
• Application: Industrial
• Weight: 100-1000kg
• Feature: Durable, Easy To Use, Effective, High Demand
• Voltage: 220V
• Condition: New
• Finishing: Polished
• Automatic Grade: Automatic
• Power: 1-3kw
• Brand Name: Active
• Power: 10 kW
• Ambient Temperature: Up to 480 Degree Celsius
• Cooling Capacity: 100 TR

Water chilling plants are used when the water is required at a temperature that is below the ambient temperature or when the cooling water temperature from the cooling tower is insufficient. Water chilling plants are mainly used in cooling and maintaining temperature of industrial equipment and machines, cooling of drinking water etc.In water chilling plants the water is chilled with the help of refrigeration system. For achieving cooling temperature below 0°C, Brine can also be added into the system.

We manufacture precision engineered Brine Chilling Plants that are extensively used for various purposes in chemical process plants, anodizing / electroplating plants, latex cooling, laboratory applications and many more. Our Brine Chilling Plants are made using compressors from Emerson and Danfoss. This makes our Brine Chilling Plant energy efficient and user friendly. The compact & modern design and use of two stage compressors with sub-cooler and related accessories have made our Brine Chilling Plant a preferred choice in the market. Salient Specifications : Easy achievement of temperatures as low as -50oCCan be provided with insulated brine storage tank & re-circulating pumpSuitable for applications that demand temperatures ranging from +6oC to -50oC

• Automatic Grade: Automatic
• Size: Medium
• Phase: Three Phase