Impeller Dealers in Chennai

• Type: Industrial Impeller
• Material: Metal
• Thickness: 10-20mm
• Weight: 1kg, 2kg
• Application: Industrial Use
• Feature: Anti Corrosive

Types And Description Backward inclined, backward curved blades Backward inclined, backward curved blade is a highly efficient impeller design. Its employed to handle air and also used for gas medium containing lighter amounts of dust particles and at high temperatures. Reinforcements and surface hardening are done for extra strength, if required. Backward inclined, flat blades An efficient and strong shape, this design is a cost-effective alternative to the backward curved design but with flat blades instead of curved and radial tipped. This results in a slightly lower efficiency, compensated by handling moderate dust particles. Backward inclined, forward curved blades Mostly known as radial tipped blades, this design reduces the potential for dust build-up on the underside of the blades in applications with light or moderate amounts of gas-borne dust. Backward inclined, forward curved blade is an intermediate design for volume and pressure. Backward inclined, aerofoil blades Aerofoil bladed impellers are most commonly used in applications handling large volumes at low pressures. This highly efficient design of fan is used in clean air or with gases containing small amounts of erosive particles. Radial blades Blades running from hub to impeller tip without any curve or inclination essentially a large paddle wheel. This design results in a relatively inefficient fan with power consumption higher than that using the much more common backward inclined blade.Its mechanical strength and resistance to wear makes the fan to handle applications when high quantities of abrasive dust are present in the gas stream or when very high temperature in the gas is expected. Configurations Single or double inlet A double inlet impeller consists of two single inlet impellers back to back on the shaft may or may not sharing a common back plate, providing almost double the flow of a single inlet fan. The selection of a double inlet fan results in a smaller diameter, compact compared to two single inlet fans. Hence a centrifugal fan has a descriptive term as SISW (Single inlet single width) or DIDW (double inlet double width). Single or multiple stages A multi-stage fan consists of two or more impellers mounted on the same shaft. The air or gas flow passes through each one in turn, with a consequent increase in pressure.

The Shot Blasting Machine Impeller, provided by us, is reckoned due to its long lasting service life. As a reliable name, we ensure that payment procedures remain secured with us. For this, we issue invoice to the customers stating the products, quantities and agreed prices. Experts' assistance is what makes our packaging reliable and highly durable as well. The packaging material used is certified and experts approved to ensure complete safety.

• Material: Mild Steel
• Structure Type: Single
• Features: Rust Proof
• Surface Finish: Paint Coated
• Packaging Type: Box

• Material: SS 304 / 316.

Centrifugal Blowers Centrifugal fan forms an important part of an industrial application that requires air for process. Centrifugal blower operates on the principle of centrifugal force, as the impeller rotates at high rpm, it pushes the air at inlet towards its periphery and is guided along the blades. Centrifugal blowers are more efficient, smaller in size and produce high pressure in comparison to axial flow fans.

  The impellers are produced with high quality casting to give dimensional and hydraulic repeatability to ensure performance parameters. Each impeller is dynamically balanced to ensure that the complete rotating element is correctly balanced in replacement of OEM spare parts.   We can develop Impellers of Radial, Mixed flow, open, closed and non clog cylindrical vanes Size: Dia from100mm to 500mm Material: Ni Hard, Hi Cr Delivery: Mutually agreed schedule   Advantages: FLOWEZYY spares are durable and has a long wear resistance life Quick payback on investment Superior quality casting gives dimensional and hydraulic repeatability to exceed performance Highly demanded for abrasive and corrosive application Continuous Research and up gradation on tailor made spares High rugged reliability with excellent service support The highest yield at a lowest input allowing the balance between the quality and price, followed by low maintenance cost result in substantial saving Indigenously manufactured spare components result in faster delivery and easy spare availability Better interchangeable- substitute of spares as compare to OEM Massive reduction in spares consumption Manufactured under strict supervision

Backward curved impeller very good cooling at high pressure conditions. The impellers of these industrial fans are highly resistant to dirt & dust. Hicool manufactures Backward Curved Fans of frequency 50Hz and 60Hz.

These are most efficient axial flow impeller. It is recommended for blending, solid suspension, heat transfer etc. It provides maximum flow at minimum power. Mostly available in three blade version. But different number & width of bade are also common in special applications. This is also called as fabricated propeller. 

• Type: Fan Impeller
• Material: Brass, Copper, Metal, Plastic, Stainless Steel
• Shape: Round
• Thickness: 10-20mm, 20-30mm, 30-40mm, 40-50mm50-60mm
• Weight: 1kg, 250gm, 500gm
• Color: Golden, Grey, Light Brown, Silver
• Finishing: Non Polished, Polished
• Application: Industrial Use
• Feature: Anti Corrosive, Fine Finishing, Good Quality, Immaculate Finish, Robustness, Strong Strength

Depending on the medium of fan and operating temperature. Impellers can be offered Pressure diecast Aluminum ,Nylon & PAG( poly amide Glass fibre ), Impellers can be offered in fixed pitch and variable pitch. We can also fabricate impellers in stainless steel , M.S. & FRP . Fan casing can be manufactured out of M.S. , stainless steel , M.S.& FRP lining. Axial Fans are designed for optimum effeciency and low noise levels. Capacity ranging from 1080 m3Hr to 252000 m3Hr with static pressure upto 75 mmwc can be offered. PAG impellers are widely recommended for energy conservation over conventional heavy aluminum impellers. Variable pitch impellers do have the flexiblity to varry the capacity by changing the blade pitch angle.

Backward curved with aerofoil blades Backward curved laminar blades Forward curved blades Forward curved radial tipped blades Radial blades Paddle type blades

• Type: Impellers
• Material: Mild Steel
• Shape: Round
• Thickness: 10-20mm, 20-30mm, 30-40mm, 40-50mm50-60mm
• Weight: 250gm, 500gm
• Color: Golden, Grey, Light Brown, Silver
• Usage: Industrial Use
• Finishing: Non Polished, Polished
• Specialities: Anti Corrosive, Fine Finishing, Good Quality, Strong Strength

• Voltage: 380v/50hz
• Power: 2200w
• Pressure: 24.5kpa
• Weight: 45kg
• Output: 210m³/h
• Dimension: 422*388*424mm

• Brand Name: Cutom Specification
• Material: Stainless Steel
• Closing Type: Open
• Structure Type: Single
• Impeller Blade Type: Forward-curved
• Usage/Application: Industrial
• Minimum Order Quantity: 5 Piece

• Type: Impellers
• Material: Brass, Copper, Metal, Stainless Steel
• Shape: Round
• Thickness: 10-20mm, 20-30mm, 30-40mm, 40-50mm50-60mm
• Weight: 250gm, 500gm
• Color: Golden, Grey, Light Brown, Silver
• Usage: Industrial Use
• Finishing: Non Polished, Polished
• Specialities: Anti Corrosive, Fine Finishing, Good Quality, Immaculate Finish, Strong Strength

We are the main supplier of this product.

• Impeller Diameter: 125 to 180 mm
• Usage/Application: Industrial
• Input Voltage: 110, 220, 440 V AC (50/60 Hz.)
• Power Input: 60 to 350 W
• Air Flow: 200 to 2000 m3/hr.

• Material: Mild steel
• Total Efficiency: More than 80%
• Voltage: 220 - 240 V AC
• Speed: 1440 RPM
• Air Volume: 8640 m3 /h
• Outlet Velocity: 7.43 m/s
• Power: 2.55 kW
• Noise Level: 80 dB (A)
• Frequency: 50 - 60 Hz

We offer Titanium Impeller as per customer design, drawing and specifications. We are reckoned as one of the leading Manufacturers, Exporters and Suppliers of Titanium Impeller. Our Titanium Impellers are fabricated from Titanium Plate, Rod, and Fasteners and from mill products. Our Titanium Impellers are manufactured as per ASTM standards. Highlights Available in different specifications and sizesManufactured as per ASTM standardsSturdyLonger life

We are supplier & manufacturer of water pump impeller.

The Industrial Impeller, we supply, is known for its robust fan blade construction and long service life. These Industrial Impellers are extensively used in marine, agricultural and other industries. We source Industrial Impeller from the leading Industrial Impellers manufacturing brands. Further, these Industrial Impellers in which we deal are appreciated for noiseless operation and reduced vibration. Types Non-over loading ImpellersID fan impellersBackward Curved / Aero Foil Blade ImpellersDouble Inlet (NOL) ImpellersImpeller with adjustable GRP / NYlon / Aluminium BladesBackward Curved / Radial Tip Impeller.

Kirloskar Impeller, Manhole Covers, tap set, PVC Tape, Road Safety Jacket