Inspection Systems Dealers in Chennai

Gantry Based UT Inspection system has been developed for both weld and body lamination inspection system. The system achieves very high inspection speed of 25-30m/sec.Some of the specification for this system are as below : Pipe Diameter - 6-20 Length - 6-18m Scanning Speed - 25-30m/min Laser Seam Tracking 8 channels for Weld and 16-24 Channels for Body Qualification : API The gantry type lay out gives the flexibility in installations depending on customer's mill lay out. System meets the API norms and can be adapted for customers' specific requirement.

IRIS is a non-destructive testing technology for pipes and tubes that uses ultrasonic waves.Many plant operators in the oil and gas and power production industries face the issue of increasing asset efficiency and life expectancy while maintaining safety and reliability. As a result, proper inspection of critical components such as pipes and tubes is critical to maintaining the plant's integrity.Internal Rotary Inspection System (IRIS) is a tube inspection system that can detect corrosion, pitting, and wall loss in boilers, heat exchangers, air coolers, and feed water heaters. IRIS is extremely versatile since it can be used on a wide range of tube diameters and wall thicknesses, and it is suited for both ferrous and non-ferrous materials. n IRIS probe is inserted into a tube flooded with water. The probe is fitted with a transducer that generates an ultrasonic pulse along a path parallel to the axis of the tube. A rotating mirror directs the ultrasonic pulse into the tube wall. The mirror is driven by a small turbine that is rotated by the pressure of water pumped into the tube. The ultrasound pulses are reflected by the inner-diameter (ID) wall and outer-diameter (OD) wall of the tube and the time-of-flight difference between the two diameters is used to calculate the wall’s thickness. As the IRIS probe is pulled, the spinning motion of the mirror results in a helical scan path ensuring full coverage of the tube. Merits of IRIS Tube Inspection Suitability for ferrous and non-ferrous materials. Detection of corrosion, pitting and wall loss. Accurate wall thickness measurements.     Sensitivity to both internal and external defects. Defect position can be located in relation to tube length. Flexibility as a back-up to remote field, magnetic flux leakage and eddy current inspections.

• range: 2000mm.

Laser Inspection System it is highly accurate and measures thickness at micron levels.The Laser sensor we used in our system is capable of measuring +- 30 microns,which gives the ability to measure thickness of sheet metal quickly and accurately. We also do some customization in our software to cater the needs of our client.We use MicroEpsilon high precision sensors for thickness measurement,in our system to inspect various sheets ranging from few mm to 2000mm.

Using panel light installed at the top and CCD camera below to inspect the clogging of stencil aperture to eliminates poor quality stencil being used, ensure quality printing right from the start.

• Frequency: 50 Hz
• Voltage: 480 V
• Brand: Imatics
• Phase: Three Phase
• Machine Type: Automatic
• Usage/Application: Industrial
• Capacity: 800 pieces/hour

Can inspect Length, External and Internal diameters, Incomplete processed articles, Head cracks, Head height, Pitch, Thread numbers and Slanted thread, Broken pin.   Features Can check the presence/absence of a part in an object Check cut-on outer profile Inspect nuts, rods, washers, fasteners, O-rings, and special parts. Can check Visual and dimensional defects Achieve high speed, industrial automation and integration with our solutions Choose from Kanshi, FlatInspect, Shinsei, and Ryouten based on your product type and inspection needs Easy integration with the factory workspace. Enhance your assets including Robots & Cobots with AI capabilities Customize your solution to fit your product and people requirement   How does it benefit you? Inspect large products with 100% visual accuracy and find even the smallest defects Boost your production speed and reduce waste with faster processes Deliver reliable and accurate products to your customers and increase their satisfaction

YXLON International a company of COMET Group is worldwide leading manufacturing and supplier of Industrial X-ray Systems and Industrial Computed Tomography ( CT ) systems for non destructive testing of materials ( NDT). YXLON offers Application and Testing services with customer support world wide.Detail detectability

Magnetic Particle Inspection System is a multidirectional magnetization unit with capability to magnetize up to 6000 Amps. Magnetic Particle Inspection System offered by us provides alternating current (AC) and full wave DC (HWDC) as test current for effective magnetization and surface and subsurface detection of cracks. Magnetic Particle Inspection System can be used in industries like Forging Shops, Aircraft Overhaul Stations and Heat treatment Plants where high magnetizing currents are required with high level of accuracy. We offer Magnetic Particle Inspection System at competitive prices. Features : Contact shot for Circular magnetization & Coil shot for longitudinal magnetization of parts. 6000 Amps. AC & 6000 Amps HWDC Fabricated Frame (M.S.) with splash guard & wood grill assembly Stainless Steel circulation tank of SS�304 Grade Material with Turbulence agitation system, Mono-Block Pump and Hand Nozzle. Rugged construction for reliable magnetic inspection. In-built power source with infinitely variable self-regulating current control. 5 turn 550-mm. dia base mounted coil. Pneumatically operated headstock with foot switch (100 mm stroke length) & rail mounted hand-operated tailstock, both with steady rest for heavy job handling. Analog Ammeters with calibration facility. Control Panel with push bar assembly In-built AC decay Demagnetization facility. Black color Inspection hood of resin for Fluorescent wet particle inspection of jobs under ultraviolet lights. AC / HWDC changeover by Selector Switch Magnetization Time controlled by Logic Control PCB. Current assurance indicator with audiovisual facility.

The Paint Inspectors Kit is a comprehensive kit of equipment, which will cater for the day-to-day standard requirements of the Industrial Painter and Inspector.The Paint Inspectors Kits contains the following listed equipment. Paint Inspector Kit in one carrying case with the entire basic test instrument make inspector’s job easy. Highly recommended for QA / QC dept. of paint shops   Kit K2002 Contents C2200 – Coating Thickness Meter with carrying case (Refer various options)F1009 – Set of 8 Precision Measured Calibration FoilsZ1003 – Steel Zero PlateT2002 – Infrared Digital ThermometerH2005 – RH%-Dewpoint MeterW2001- Wet Film Gauge (Stainless, range 25µm to 1,500µm 45 teeth)R1002 – Testex Tape roll (X-Coarse)R1004 – Testex Snap GaugeR1003 – Burnishing toolR1006 – Surface Profile GaugeU1005 – Inspection Manual of Coating Defects

• Power: 2 HP
• Input Power Supply: 415 V
• Maximum Pressure: 6 kg /cm2
• Frequency: 50Hz

• Size: 3mX2m, 2mX1m,1X1m
• Type: Benches
• Material: Steel, Stone
• Shape: Square/Rectangular
• Certification: ISO/IEC:17025-2016
• Application: Industrial
• Color: Grey
• Feature: Long Life
• Condition: New
• Surface Finishing: Polished
• Country of Origin: India

• Usage/Application: Industrial
• Capacity: 2-5 Ton/Hour
• Phase: 3 Phase
• Voltage: 380 V
• Frequency: 50 Hz
• Power Source: Electric

• Warranty: life Time
• Country of Origin: Made in India
• Usage/Application: Textile Industry

To inspect batch no, expiry date other text missings. To inspect print quality OCR application To inspect packing quality like sealing, taping etc.

Highly Precise and Accurate In-Line AOI system from GMS, Malaysia, SPOIS works on the principle of synthetic modeling of components. SPOIS does not rely on comparator principle of comparing all PCBs with the Golden Board, thus avoiding false alarms. SPOIS has a unique capability to detect defects at any stage of SMT manufacturing. It can be placed after the Stencil Printer to detect Printing defects, or after the Placement equipment to detect Placement related defects, or after the Reflow oven to detect Soldering related defects. Priced much lower than conventional Inline AOI systems, and slightly higher than the conventional Table Top systems, SPOIS can achieve ROI in record short times. The NG Marker (Optional) can mark the defect on the PCB making it easier for the Rework Operator to identify and rework the defect.

Master Linque Automation is the technology and methods used to provide imaging-based automatic inspection and analysis for such applications as automatic inspection, process control, and robot guidance in industry. Most problems start at the very beginning of a product’s journey on the production line. Getting it wrong there can have disastrous consequences.However, with our machine vision systems in place, you can instantly improve your production processes so that the products you produce are made at higher speeds, without defects, and at lower cost.Automation often demands vision. Our vision systems perform tasks that are practically impossible for people to do reliably and consistently. With the widest range of integration tools available, our vision systems interface to virtually any factory network or automation control system. Our clients can avail from us Industrial Machine Vision System. The Vision System is used in Production line for the 100% quality assurance. It inspects for visible defect in the product/printing at high speed. Vision Inspection is completely replacing Manual inspection using higher accuracy and higher speed compare to Manual InspectionBestowed by a modernized infrastructure facility, our organization is manufacturing, supplying and export a wide gamut of optimum quality Vision Inspection System which are manufactured and designed using fine quality material and as per international quality standards. Offered range of vision inspection system can be availed from us reasonable price.

• Brand Name: DatCAM
• Country of Origin: Made in India
• Features: Measures inside diameter (ID) features such as undercuts, chamfers, threads, rifling, O-ring grooves, splines, lands, and edge breaks
• Usage/Application: Laboratory

Video Inspection System is reasonable for therapeutic gadget, SMT weld joints, machine parts, electronic segments, metallurgic, deformity investigation and lab research.Our organization is principal for offering Video Inspection System to clients.This item is fitted with an information processor that is perfect to auto miscreant.

The images we “see” are perceived by millions of optic nerves and each of them “captures” a tiny fraction of the image and stores it. In a camera the “frame” quality depends on the number of points used to store the image. These points are the pixels, which form the electronic film of the camera. The CCDs (Charge Coupled Devices) are usually small in size, 5x7mm for example, and contain thousands, millions of pixels depending on the the instruments quality.

Fabric Inspection Machine, Leather Garment, Leather Garments

This is an indispensable tool to assure quality to print buyers in a professional way. The detection system is featured with high precision camera and advanced software. Quality inspection and sorting machine on modern standard.

Surface Inspection System, Machine Vision / Industrial Cameras

food inspection systems, Bitumen Penetrometer, Inspection Mirror

Video Inspection System

Integrated Radar Inspection System, Spring Closed Brake

inspection equipments, coil cradles, Hoppers, Special Purpose Machines

quality inspection system, Printing Machines, packaging printers

Magnetic Particle Inspection Equipment, Ndt Equipments

Vehicle Side Mirror Inspection System, Control Panel Board, Proximity Sensors

under vehicle inspection system