Testing Equipment Dealers in Perumbakkam, Chennai

  This test helps in determining the ability of a coating to resist degradation due to mechanical wear by hard and rough objects. Abrasion resistance can be enhanced by incorporation of surface modifying additives. Adhesion:   Adhesion testing in the paint and coating industries is necessary to ensure the paint or coating will adhere properly to the substrates to which they are applied.Test Method: IS: 101 (P-5)(SEC-2)1988 Alkali Resistance of Paint:   This test helps in determining the degree to which a paint resists reaction with alkaline materials such as lime, cement, plaster, soap, etc.; a necessary property for paints in bathrooms, kitchens, laundries.Test Method: IS: 427-2005, IS: 428-2006 Cass Test:   This test helps in determining the corrosive performance of decorative copper/nickel/chromium or nickel/chromium coatings on steel, zinc alloys, aluminum alloys, and plastics designed for severe service. It is also applicable to the testing of anodized aluminum. Chemical Resistance:   This test helps in determining the ability of a coat to resist chemical deterioration or staining.Test Method: IS: 13630 (P-8) 2006, EN 105-106 Chip Resistance:   This test helps in determining the resistance of surface coatings (paint, clear coats, metallic plating, etc.) to chipping caused by the impacts of gravel or other flying objects. Coating Hardness:   This test helps in determining the hardness of paint coat.Test Method: IS: 101 (P-5)(SEC-1)1988 Coating Surface roughness /Profile:   The proper and effective preparation of a surface prior to coating is essential. Making sure that the correct roughness – or profile – has been generated is essential. If the profile is too low, the adhesion of the coating to the surface will be reduced. Too high and there is the danger that the profile peaks will remain uncoated.Test Method: Coating Thickness:   This test helps in determining the thickness of paint plating, coatings and galvanizing on iron steel.Test Method: IS: 6745-1972 Condensing Humidity:   This test helps in determining the resistance of organic coatings by controlled condensation. Condensation is produced by exposing the test surface of the sample to a heated, saturated mixture of air and water vapor, while the reverse side of the sample is cooled to room temperature air.Test Method: IS: 101 (P-6) (SEC-1)1988 Crosshatch Adherence:   This test helps in determining the adhesion of a large variety of coatings.Test Method: Cyclic Corrosion:   This test helps in determining the corrosion degradation of coating systems for steel bridges.Test Method: Drying Time:   This test is done to know when a coating is totally dry. When developing a process, it is often important to know the exact time it takes for the coating to dry or cure. There are many stages to the coating drying time. Once a coating has been applied, the first stage is that the coating levels off under gravity. Once a coating begins to cure, a thin dry film appears on the surface. The coating then continues to dry and finally after a period of time, the coating is totally cured.Test Method: IS: 101 (P-3) (SEC-4)1986 Failure Analysis:   This test helps in determining when, where, and how the paint or coating failure occurred.Test Method: Falling Weight:   The ability of a pipe coating to resist mechanical damage during shipping, handling, and installation will depend upon its impact resistance. This test method provides a systematic means for screening coating materials with regard to this property.Test Method: Flexibility:   This test helps in determining the ability of a coating system to withstand the stresses of fabrication. Organic coatings on precoated sheet are subjected to stresses when fabricated into products by roll forming, brake bending, or other deformation processes. These stresses can exceed the flexibility or adhesive strength of the coating, resulting in fracture of the coating which exposes the substrate, or in the loss of adhesion of the coating to the substrate.Test Method: Gloss (60deg.C):   Gloss measurement is essential instrument where a cosmetic appearance of the coating finish is required. It measures, guide to control and test right from matt to mirror finish accurately. Multi directing a beam light at a specific angle to the test surface and measuring the amount of reflection determine gloss. For general gloss measurement the 60º angle is recommended.Test Method: IS: 13607-1992, IS: 5691-1970 Hardness:   This test method covers a procedure for rapid, inexpensive determination of the film hardness of an organic coating on a substrate in terms of drawing leads or pencil leads of known hardness. This test covers the determination of the indentation hardness of organic materials such as dried paint, varnish and lacquer coatings, when applied to an acceptable plane rigid surface, for example, metal or glass.Test Method: ASTM D3363 / ASTM D1474 Impact resistance:   Impact performance after painting/printing can be tested with several impact tests, like a puncture test or a falling dart test.Test Method: IS: 101 (P-5)(SEC-3)1999 Moisture Content:   This test helps in determining the total water content of paints using a calcium hydride reaction test kit, or water content between 2 and 85 % water.Test Method: Peel:   This test is used to measure resistance to cracking (flexibility) and adhesion of attached organic coatings on substrates of sheet metal or rubber-type materials.Test Method:   Salt Spray:   The salt spray test is a standardized test method used to check corrosion resistance of coated samples.Test Method: IS: 2074-1992, IS: 13183-1991, IS: 13607-1992 Scratch Resistance:   The scratch resistance can be established e.g. in the Taber abrasion test, where the amount of haze is established after a number of abrasive cycles. The scratch resistance can also be determined quantitatively by measuring the weight loss after a number of sanding cycles. The pen test determines the indentation caused by a sharp pencil applied with a defined force.Test Method: ISO 1518 Volatile Content:   This test helps in determining the weight percent volatile content of solvent-reducible and water-reducible coatings.Test Method: ASTM D2369, IS: 101 (P-2) (SEC-2)1986 Water Content:   The amount of water that paint coat could absorb is measured by the water content test.Test Method: IS: 101 (P-2) (SEC-1)1988 Water Resistance: Water can cause the degradation of coatings, so knowledge of how a coating resists water is helpful for assessing how it will perform in actual service.Test Method: IS: 101 (P7SC-1)1989, IS: 13183-1991, IS: 5691-1970  

Prominent & Leading Manufacturer from Chennai, we offer Injection Machine Electricity Meter.

Accept input rtds, thermocouples, voltage , current process temperature , pressure, humidity ,level flow,co2, air velocity, diff pressure etc,1000 readings per channel memory with rtc display range -1999 to 9999 counts ,1-24 channels scan time, print time , skip, offset , input selectable available with large display sizes 2" and 4".

Special Clips for Special type of devices. Properly identified IC Pins for easy and faster testing. Easy to Handle design for continuous operation. Suitable mainly for Rugged application with Gold plated and spring loaded pins. Pins are evenly spaced to match the component package suitably without any Misallignment for proper contact.

The Panther 4HT Wire Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch. This reduces the time required to generate tedious test programs for troubleshooting open short defects in Devices. Its fast test time per pin combination is useful because it helps to increase the test yield and productivity. It offers unique MASTER and SATELLITE UNIT Options to avoid looping back the cable to the ATE and Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts Ships and similar applications where large cable looms are used FEATURES: Expandable hardware channels Unique MASTER and SLAVE or Satellite Units concept User friendly software suite Learns from sample board Creates user defined template test log for verification

CAN BUS TESTER 2 - GEMAC, Electrical Slip Ring

hour meter, Gsm Modem, computer software services

Instrumentation Panel, solar panel structure, electrical commissioning

4HT Master Slave DSU Wire Harness Tester

three phase reference standard meter, single phase reference standard meter

electronic energy meters, industrial LV panel boards, Luminaries, Fans

industrial automation pcb tester, Weighing System