Able tech Engineering Chettipalayam, Coimbatore, Tamil Nadu

ate manufactures wire-fin oil coolers for cooling oil in various industrial application areas. Wire wound fin tube consists of a base tube with oval or near rectangular loops formed of wire which are wound helically over the tube with root soldering of foot of every loop to the tube.the loop of wire creates greater turbulence thereby increasing the heat transfer coefficient. Root soldering along the entire length eliminates almost all air gaps between the fin and the tube.for most applications, wire wound fin tubes make it possible to design a much compact heat exchanger coupled with lower pressure drop compared to conventional fin tubes. Our products are corrosion resistant, offer less maintenance and best efficiency and suitable for cooling of :• hydraulic oil• gear oil• lube oilapplicationa) steam air heating or cooling applications. This is because the wire fins having a high airside coefficient are able to best utilize the very high coefficient of condensing steam.b) water heaters - coolers for the high heat transfer coefficiency.c) borewell rig compressor oil coolers. d) compact high strength but light weight heat exchangers to be used with equipment like hydraulic oil coolers, lube oil coolers and assorted oil and water coolers.

This products have been widely used in wind power generators in India. The special arrangement of tubes lowers the internal wind-resistance, improves the cooling flow of the generator and increase the efficiency.Use and applications: • Electric-Motors and Generators • Electrical converter plants • Air pre heating powered by exhaust or waste air • Heat recovery plants for process engineering Depending on the performance data required by the customer or user, several tube designs and arrangements are available: • Round tubes in triangular tube layout • Round tubes in square tube layout • Flat tubes in square tube layout Construction and design By using different arrangements of tubes (e.g."W-arrangement") the required performance and the permissible pressure loss can be achieved within the limited size of the heat exchanger. The tubes are either sealed in the tube plates with a special compound material or fixed into the tube plates by tube expansion. Depending on the operating conditions, the following tube materials can be used: • Aluminium alloy • Brass and complex brass • Cupro nickel • Steel or stainless steel

Application : Refrigeration Parts

Type : shell & tube type

Brand Name : able tech

Certification : NA

Type : Condenser

Material : copper

Condition : New

Type : SHELL & TUBE

Color : NAVY BLUE

ABLETECH ENGINEERING offers shell and tube exchangers starting at 2" IPS in all TEMA types. We design and fabricate to ASME code and TEMA standards. Our shell and tube line utilizes bare tube (straight and u-tubes), helical low-fin outside, longitudinal fins (inside & outside are available). These exchangers are suitable for a variety of applications and are offered in fixed tube sheets or removable bundles. The surface area ranges from (1) square foot to 40,000 square feet. Pressure range is from full vacuum to over 14,000 PSI (limited by size, material and design condition).  

Material : COPPER,STAINLESS STEEL

Size : 2000 CAL/HR-600000 KCAL/HR

Type : CRIMPED TUBE TYPE

Finishing : SUPERIOR

Color : NAVY BLUE

Supply Ability : 60 Unit/Units per Month

Lead Time : 56 DAYS

Material : stainless steel, mild steel

Type : finned tube type

After-Sales Service Provided : Engineers available to service machinery overseas

Abletech Engineering offers shell and tube exchangers starting at 2" ips in all tema types. We design and fabricate to asme code and tema standards. Our shell and tube line utilizes bare tube (straight and u-tubes), helical low-fin outside, longitudinal fins (inside & outside are available). These exchangers are suitable for a variety of applications and are offered in fixed tube sheets or removable bundles. The surface area ranges from (1) square foot to 40,000 square feet. Pressure range is from full vacuum to over 14,000 psi (limited by size, material and design condition).     s    

Type : Shell Tube Heat Exchanger

Material : Metal, Mild Steel, Stainless Steel

Certification : ISO 9001:2008 Certified

Application : Oil Refineries

Weight : 100-1000kg, 1000-2000kg, 2000-3000kg, 3000-4000kg, 4000-5000kg

Grade : AISI, ASTM, DIN

Color : Brown

Voltage : 440V

Condition : New

Automatic Grade : Automatic, Fully Automatic

Power : 9-12kw

Warranty : 2 Years

Driven : Fuel

Temperature : 50-100Deg C

MODEL : ATE19-RADHX Function: Used for evaporation, dryer, demisting Material of Construction: AluminumStructure: Bar and Plate Heat Exchanger Specialty: High Heat Transfer ability , Energy-Saving Heat Exchanger Application: Air Dryers General Process: 3-in-1 and 4 in 1 heat exchanger and water-oil separator model is designed specially for the Refrigerated Air Dryer. It consists of Precooler (Air to Air Plate Fin Heat Exchanger), Evaporator (Air to Refrigerant Plate-Fin Heat Exchanger) and stainless steel mesh Gas-Liquid separator filter. It has four functions: Precooling, Cooling, Separation and Filtration. There is insulating layer outside of this unit in order to reduce the loss of heat and increase the effectiveness.     Precooler and Evaporator are both aluminum vacuum brazed Plate-Fin Heat Exchangers. Compared with shell and tube heat exchanger in traditional refrigerated air dryer, the heat transfer area of plate-fin heat exchanger is larger and so the exchanger effectiveness is higher. Generally, the heat transfer area density of plate-fin heat exchanger can be 1500m2/m3, but the shell and tube heat exchanger’s is only about 160m2/m3. And the heat transfer coefficient of plate-fin heat exchanger is 5-10 times higher than shell and tube heat exchanger. Air-water separator uses optimized spiral guide structure and the main principle is to separate the liquid and gas according to the difference of the liquid weight and gas weight and using gas flow direction and the inertia of speed changing. Mesh filter is made of some steel mesh and it can filterate air secondary to increase the dry efficiency.   Features and Advantages（1）Compact size:- Reduces the total air dryer size- Significantly reduces the refrigerant hold-up volume（2）Highly efficient thermal performance and low pressure drop minimizes power usage.（3）Low price.（4）Easy to repair and long service life.（5）Full compatibility with the most common refrigerants. TestingAll of our 4 in 1 heat exchangers undergo a hydrostatic test of 1.5 times the design pressure with water for 30 minutes and a leak test of 1.1 times the design pressure with air for 10 minutes for the air side. After passed by the above tests, each unit is to perform 24 hours’ keeping pressure of 18 bar and conduct helium test for the refrigerant side, respectively.

Function: Used for evaporation, dryer, demisting Material of Construction: AluminumStructure: Bar and Plate Heat Exchanger Specialty: High Heat Transfer ability , Energy-Saving Heat Exchanger Application: Air Dryers General Process: 3-in-1 and 4 in 1 heat exchanger and water-oil separator model is designed specially for the Refrigerated Air Dryer. It consists of Precooler (Air to Air Plate Fin Heat Exchanger), Evaporator (Air to Refrigerant Plate-Fin Heat Exchanger) and stainless steel mesh Gas-Liquid separator filter. It has four functions: Precooling, Cooling, Separation and Filtration. There is insulating layer outside of this unit in order to reduce the loss of heat and increase the effectiveness. Precooler and Evaporator are both aluminum vacuum brazed Plate-Fin Heat Exchangers. Compared with shell and tube heat exchanger in traditional refrigerated air dryer, the heat transfer area of plate-fin heat exchanger is larger and so the exchanger effectiveness is higher. Generally, the heat transfer area density of plate-fin heat exchanger can be 1500m2/m3, but the shell and tube heat exchanger’s is only about 160m2/m3. And the heat transfer coefficient of plate-fin heat exchanger is 5-10 times higher than shell and tube heat exchanger. Air-water separator uses optimized spiral guide structure and the main principle is to separate the liquid and gas according to the difference of the liquid weight and gas weight and using gas flow direction and the inertia of speed changing. Mesh filter is made of some steel mesh and it can filterate air secondary to increase the dry efficiency.   Features and Advantages（1）Compact size:- Reduces the total air dryer size- Significantly reduces the refrigerant hold-up volume（2）Highly efficient thermal performance and low pressure drop minimizes power usage.（3）Low price.（4）Easy to repair and long service life.（5）Full compatibility with the most common refrigerants. TestingAll of our 4 in 1 heat exchangers undergo a hydrostatic test of 1.5 times the design pressure with water for 30 minutes and a leak test of 1.1 times the design pressure with air for 10 minutes for the air side. After passed by the above tests, each unit is to perform 24 hours’ keeping pressure of 18 bar and conduct helium test for the refrigerant side, respectively.

Type : TUBE TYPE

Color : navy blue

The general function of the Radiator is to cool liquid or gas. Radiators are made of aluminum, which has a rapid heat exchange. They are used in Compressors to cool the mechanism and the heated air. A high level of heat is released in compressors as a result of the friction of compressed air with surfaces in the system. This happens in both the reciprocating compressors and screw compressors. air with surfaces in the system. This happens in both the reciprocating compressors and screw compressors. This heat is cooled in low flow (under 1500 lmin capacity) compressors using a pulley that is connected to the engine as a fan.However,the Compressor and the air are cooled in high-flow compressors using a coil pipe or Radiator. Because there is no oil circulating in the system,only air cooling radiators are used in reciprocating compressors.However,in the screw compressor,the oil circulating through the compressor should be cooled.

the plate bundle of a plate-fin heat exchanger is composed of fin, division plate and seal packing. A fin and a seal packing, which are placed in between two adjacent division plates, form an interlayer called as passage. The interlayers are superposed into a whole by brazing, according to different flowing ways of fluid, forming the bundle of plate (or called core body). aluminum is applicable to dip brazing with salt solution, so at present the plate-fin heat exchanger is nearly made of the manganese-aluminum alloy, which is corrosion-resistant.the plate-fin heat exchanger usually is fabricated from aluminum, but regardless of the materials of construction, the core is furnace brazed in a controlled atmosphere or high vacuum. Because plate-fin heat exchangers require more precise manufacturing, they are usually more expensive than other designs.   features of plate-fin heat exchanger main features of plate-fin heat exchanger are as follows:1.  high heat transfer efficiencythe heat transfer efficiency is high is that the fin can cause the disturbance for the fluid to make the thermal boundary layer rupture and renew continuously. The heat transfer coefficient of forced convective gas is 35 to 350 w/ (m2·℃), the overall heat transfer coefficient of forced convective oil is 120 to 1740 w/ (m2·℃), while the overall heat transfer coefficient of gas-gas in the shell-and-tube heat exchanger is only 10 to 35 w/ (m2·℃).  2.  compact structure and light weightits heat transfer area per unit volume is generally 1500 to 2500 m2/m3, which is 8 to 20 times that of the shell-and-tube heat exchanger. The weight of aluminum plate-fin heat exchanger is one tenth that of the shell-and-tube heat exchanger with the same heat transfer area, but its metal consumption per unit heat transfer area can be dozens of times smaller than the shell-and-tube heat exchanger.  3.  wide range of application it can be applicable to the heat transfer of various different fluids such as gas to gas, gas to liquid and liquid to liquid. Depending on the arrangement and combination of various flow passages, the plate-fin heat exchanger can adapt to the heat transfer in different working conditions such as countercurrent, cross flow, multi-flow and multi-pass flow. The plate-fin heat exchanger can be shaped and produced in batch to meet different requirements, so the cost can be reduced and the interchangeability is enlarged.  4.  the manufacturing process is complicated and the requirements for manufacture are strict.  5.  it is easy to be blocked and the cleaning and maintenance are difficult. If the inner leakage occurs owing to the corrosion, it is hard to maintain the exchanger. in the practical production, the plate-fin heat exchangers made of aluminum are used for air separation device, petrochemical device and mechanical power equipment, and their service ranges are as follows:the design temperature is from -200 to 150℃, and the design pressure is from 0 to 0.6mpa.

model : ate36-loc ate design,manufacture and export lube oil coolers of exceptional quality with reasonable price. The lube oil cooler we supply is in high demand and finds usage across industries. The lube oil cooler we export is the best variety available in the market. Lube oil coolers can be plate type lube oil cooler or ptloc   model: ate30-ptloc and shell and tube type lube oil cooler. model:ate31-locst as far as plate type coolers are concerned, cleaning is much easier. Shell side of lube oil coolers are normally designed with baffles and fins for enhanced heat exchange. Chemical cleaning is carried out regularly for the shell side. This removes sludge adhered inside and increases heat transfer efficiency.   application   railways marine cement plant steel plant chemical plant breweries

an air compressor is a device that converts power (usually from an electric motor or an engine) into kinetic energy by compressing and pressurizing air, which, on command, can be released for use elsewhere.often the compression takes place in two stages.the process of compression produces energy which is manifested as heat. The heat is removed before use (or further compression), hence the introduction of intercooler and aftercooler.     situated between the first and second stages of an air compressor, the intercooler cools the compressed air before it is further compressed.ate uses technology similar to its diesel engine turbo-charged air coolers for this process. Water cooled with fins on the airside. These are fabricated using high grade raw material at our modern manufacturing unit. The use of hi-tech machines in the manufacturing process ensures that the end product is defect-free. These multi-stage industrial compressors are extensively utilized for optimizing the cost of compressing gases, as air compressor compresses air, after which heat is generated that causes the air to expand.ate can provide just the intercooler element or the entire unit including the outer casing. Series production for om requirements is already carried out for leading compressor makers, but we are also able to design and build for bespoke special requirements.     situated on an air compressor immediately after the air is compressed, the after cooler reduces air temperature before it is used for the end purpose. ate uses technology similar to its diesel engine turbo-charged air coolers for this process. Water cooled with fins on the airside.ate can provide just the after cooler element or the entire unit including the outer casing. Series production for om requirements is already carried out for leading compressor makers, but we are also able to design and build for bespoke special requirements.                 features high performance low power consumption sturdy construction easy operation our line of atlas copco non-oem parts meets oem standards. non-oem aftercooler & intercooler zr 3 models zr 4 models zr 5 models zr 6 models non-oem aftercooler & intercooler zr 110-145 modelszr 160-275 modelszr 300-425 modelszr 450-750 models

Size : 6 FEET X 6 FEET X 1/2 FEET

Brand Name : ABLETECH

Material : brass ,copper

an hydraulic oil cooler is a device designed to prevent oil used in hydraulic systems from overheating. Common hydraulic oil cooler designs include radiator, shell and tube, or plate and frame types.      advantages of hydraulic oil cooler1. High heating efficiency for oil cooling2. Compacted size3. Easy installation4. Stainless steel shell & tubes.5. Various connectors for connection.6. Drain water and drain oil connectorsate offers wide ranges of hydraulic oil coolers for all industrial machine hydraulics for system cooling.   air to oil cooling in brazed aluminum plate & bar                         up to +500 hp of heat removal from hydraulic oil round tube copper, brass or steel brazed aluminum plate & bar (p-bar™) extruded aluminum tube (t-bar™)  aluminum/steel fin construction all aluminum brazed     water to oil cooling in shell & tube:             steel, copper, copper/nickel, or stainless steel construction brazed plate construction internal fins diameters up to 10 inches lengths up to 12 feet applications our hydraulic oil coolers are used worldwide in a broad range of industrial applications, including: hydraulic presses plastic injection molding lube oil coolers extrusion machinery gear boxes hydraulic power units  

Color : navy blue

Type : shell & tube type

After-Sales Service Provided : Engineers available to service machinery overseas

Material : copper ,brass ,aluminum

Condition : New

Condition : New

Type : plate & bar type

Color : navy blue

After-Sales Service Provided : Engineers available to service machinery overseas

Material : aluminum

Brand Name : ABLETECH

Type : shell & tube

Material : stainless steel

Color : navy blue

our heating and cooling coils range is the result of over 15 years of experience in the sector both on the engineering and on the manufacturing sides. Coils for heating, cooling, and heat recovery can be manufactured to almost any size using ½” or 5/8” o.d copper tubes with aluminium or copper fins and galvanized or stainless steel casings for duct or ahu mounting.     steam heating coilssteam air heating coils for air conditioning and process heating using dry saturated steam.coils can be manufactured to suit almost any size of ducting, plenum or air handling unit. hot water heating coilshot water air heating coils for air conditioning and process heating using l.p.h.w., m.p.h.w., h.p.h.w. Or low grade hot water generated from other equipment. chilled water cooling coils chilled water air cooling coils for air conditioning and process cooling which can be used with ethylene or propylene glycol solutions for low temperature applications.    dx cooling coilsdirect expansion air cooling coils for air conditioning and process cooling which can be used with hfc and hcfc refrigerants.ate manufactures heating and cooling coils for:- air handling units - ventilation- refrigeration - marine applications- food processing industry - industrial applications- special applications features:- up to 9.5 m coil length- construction according to your standard and drawing - many materials and geometries available - replacement coils - 2 weeks delivery - many accessories available 

Brand Name : ABLETECH

Material : COPPER,MILD STEEL,CARBON STEEL,BRASS,CUPRONICKLE,STAINLESS STEEL

ATE produces these tube bundles to TEMA Standards, so you do not compromise safety and quality for less cost and lead time. We guarantee our tube bundles will perform as well as or better than your original bundles. Our tube bundles are dimensionally interchangeable, cost-effective, and reliable.Tube bundles are pressure tested at 225 psi. each tube is independently reviewed for structural soundness as well as the tube sheet joint for each tube.     Tubes can be plain, low-finned (internal and/or external) or high-finned (integral or applied fin) with many methods for tubeside/shellside enhancement available.Tube to tubeplate/tubesheet jointing methods include roller-expansion (with or without expansion grooves) and/or welding in addition to secondary seals such as grommets, o-rings, hydroscopic and compression seals.