Cooling Towers Dealers in Madukkarai, Coimbatore

Based on the leading-edge cooling technology, the Wooden Cooling Tower, which we offer, is manufactured in confirmation to the set industrial standards. We offer the best Wooden Cooling Tower at the best rates. We are a dependable Manufacturer, Supplier and Exporter of Wooden Cooling Tower. Why Our Wooden Cooling Tower? High cooling efficiencyCompatible sparesEasy maintenanceLow noise Timber : All timber is Pine wood and is treated with Chromate Copper Arsenates. All plywood components are treated marine grade water proof plywood. All sections are fully machined prior to treatment. Structural Framing : Structure is bolted and is designed to withstand all operational loads and wind pressure. Hardware : Hardware such as nuts, bolts, washers, ring connectors etc. shall be Hot dip galvanized steel. Internal Fill & Fill Support : Rectangular Fill splash bars are designed to offer maximum splash and wetted surface in such a manner that it permits no dislocation of splash bars and yet allows them to expand or contract with changes in moisture content of wood without cracking, warping or sagging. Splash bars are supported in GRP grid supporters, which are firmly attached to structural girt members. Drift Eliminators : These are made of treated timber planks supported on grooved treated plywood Eliminator frame in herringbone pattern or PVC in Construction. Casing & Air Inlet Louvers : These will be made of corrugated AC Sheet or FRP Sheet. Tower corners are covered by FRP boards. Casing is water tight sealed. Air inlet Louvers are of corrugated AC Sheets or FRP Louvers. Distribution System : Cross flow towers employ a swamped pan distribution. The open pan covering the entire fill area distributes hot water evenly over the fills by means of PVC nozzles. Fan Deck : The fan deck is of FRP OR MS/HDG Construction with Motor frame & Fan Guard. Fans Dynamically balanced Cast Aluminium Alloy / FRP Fan Motor TEFC-IP 55 With EN -8/9 Shaft & Class F insulation.Direct Drive Ccs Timber Cooling Tower

Dry Cooling Tower Design   JC Equipments are designed and developed with to work with any size for various industries. Our Dry Cooling Tower designing department is routine updated with world standards according to the International Standards designing by CTI membership. Dry Cooling Tower Designing teams are technically qualified of engineer with facility to meet various application need.   Applications of Dry Cooling Tower   Dry Cooling Tower used for air compressor Lots power plants are using the Dry Cooling Tower Steel manufacturing industries are used Dry Cooling System Dry cooling towers for geothermal power plants Diesel Power Plants are using this type of cooling tower   Advantages of Dry Cooling Tower   No water consumption in this type of Dry Cooling Tower System because the air does not in a straight line contact between the water. This cooling tower efficacy ensures minimum ecological impact A huge of water gets conserved on using dry cooling towers. Less water resources and greater than before water pollutions concerns have led to explosive development of Dry Cooling worldwide   How to Design Dry Cooling Tower?   We are designing the dry cooling tower as per the client requirements and we having 23 years experienced in cooling tower industry. We have well designed and develop the timber cooling tower for various industries. Our designing department is updated and very qualified engineers with designing knowledge and designing standards by cooling tower technology (CTI Membership).   If the thermal power plant is not located on the seaside or near a huge lake and if the water is either too exclusive to use a wet cooling tower, then the only cooling preference is using a dry cooling tower. A huge of water gets conserved on using dry cooling towers and Optimized cooling tower designing and develop using latest materials and latest technology construction methods.   In Dry cooling tower, Reduced yearly operating costs and it also No decomposition caused by air and this type of cooling tower performance ensures minimum ecological impact.

The Round Shape FRP Cooling Tower may call as Bottle Shape . The casing and basins are designed to withstand severe vibration, high wind load and to resist corrosion. The JC FRP Bottle shape Cooling Tower consists of Honey comb PVC fills and eliminators in a design that maximizes economy and efficiency and directly driven fan and Motor 'Minimum drift Losses'. Uniform distribution of hot water by rotating arm sprinkler. Hot dipped Galvanized hardware to withstand wind forces. The bottle shape makes possible to provide maximum cooling efficiency in minimum plan area with lower energy consumption. Specifications of Bottle Shape FRP Cooling Tower The Ranges are from 10 TR to 10000 TR. Send your requirement to get our best free quote 1. Water flow rate, 2. Hot water Inlet temperature, 3. Required cold water Outlet 4. temperature and 5. Wetbulb temperature

• Applications: Automobile Industries, , Cable Industries, and Casting Units,

We Design and Manufacture a comprehensive Seamless Cooling Tower here in India, our designing peoples concentrate much more to develop these kind of Seamless Cooling Systems as per our buyers requirement that have a single piece shell.  There are no seems, panels, rivets or plenty of fasteners in this Seamless Cooling Towers and with no compromise of Quality, Competitive price and Elegant look. Contact us for more information on our Seamless Cooling Systems.

• Brand Name: JC Brand

dear sirmadam, greetings for the day… we jc equipments pvt ltd take pleasure to introduce ourselves as one of the leading designers, manufacturers & exporting of all kind of cooling towers,heat exchangers, Frp Seemless Cooling Tower, pressure vessels columns, storage tanks, air cooled condensers, etc... in india. jc equipments pvt ltd started in the year of 1989. we have wide knowledge in this field and we have regular customers throughout the world. we are authorized manufacturers of asme and we have “u, s & r” stamp certification also. we are corporate member of cti, usa. we are a world class manufacturers and we never compromise in quality. we assure our product will be best quality and competitive price. herewith we have enclosed the product profile for your kind reference. kindly refer the attachment. looking forward your valuable enquiry for us to quote our best and competitive offers, with assuring you of our best quality and prompt service at all times.

Frp cooling towers offered by heat transfer equipments private limited are known for superior design and technology. The cooling towers are designed to meet the high standard of performance demanded by engineers. These frp induced draft cooling towers deliver compact, heavy duty and efficient cooling function and have an aesthetic design. Owing to its compactness, these frp induced cooling towers are extensively used in many process industries and in hvac applications. frp cooling tower metallic parts fully galvanized/power coated/epoxy coated. Completely corrosion resistant. Direct driven axial fan to avoided belt and gear drives. the company also manufactures frp cooling tower which is used as drift cooling tower. These products are used for reducing carry out losses of moisture drops in the air stream. And this is done through well designed multi rotary drift eliminator which is created using frp sheets.

• Type: Wooden Cooling Towers
• Material: Wooden
• Certification: ISO 9001:2008
• Application: Process Cooling
• Color: Blue, Grey
• Voltage: 220V
• Condition: New
• Driven Type: Hydraulic, Mechanical
• Warranty: 1year
• Country of Origin: India
• Brand Name: World Cooling Towers
• After-Sales Service Provided: Yes
• Cooling Type: Natural Draft Cooling, Mechanical Draft Cooling

Wooden cooling tower was developed to offer greater cooling capacity in smaller space with lower operating costs. Wooden cooling tower are generally constructed over sumps designed to accommodate wooden cooling tower.

We are leading manufacturer of timber type cooling towers.It is mechanical strength, durability and high efficiency. Manpower with vast specialized experience in Timber manufacturing is back bone of the organization. We have with us persons who have been entirely responsible from concept to final product manufacturing. We have major time tested development that has been incorporated in standards. Our CCT timber are atmospheric and mechanical cooling towers. Atmospheric towers are only for smaller capacities and mechanical draft towers are for higher range. Induced draft cooling towers are efficiency and popular due to sucking of air from the tower and exhaust at the top or side. The timbers are made out of pine or chirr wood after properly seasoned and chemically treated with arsenic chromate to with stand its life against biting, fungus and termite etc. Timber Cooling Tower Product Range 1. Wooden Single Flow and Double Flow induced Draft Cross Flow. 2. Direct Drive System. 3. Reduction Gear Box Drive Suystem. 4. Counter Flow Square / Rectangular Induced / Forced Draft Towers. 5. Packaged Wooden Double / Single Flow Induced Draft Cross Flow. 6. Fan-less Induced Draft Wooded Cooling Tower [ Atmospheric Natural Draft Cooling Towers]. 7. Re-Inforced Concrete Cooling Towers. 8. Spares For any Type and Make of Cooling Towers. Timber Cooling Tower Concepts 1.1 Economy in Operation Our Timber Cooling Towers are designed for the highest effieiency at the lowest operating cost. Fans gear boxes, fill and drift eliminators are optimized to deliver maximum cooling with minum applied horsepower for lower operating cost. 1.2 Best Performance Our Timber Cooling Towers are providing more wetted surface area for uniform water distribution and higher heat trasfer rate. 1.3 Architectural Compatability Our Timber Cooling Towers are designed to a low profile. So the appearance and general configuration blends harmoniously with surroundings. Performance and attractive appearnance are demanded. 1.4 Maintenance Free Our Timber Cooling Towers are used maintenance free materials throught the tower. The materials are used in structural and functional components, all steel is hot-dipped galvanized after the fabrication. Timber Cooling Tower Technical Specifications   2.1 Structure Main structural components and other light sections machined with selected preservative timber. And it is designed for operational load and wind pressure of 250 kg/m2 of projected area in any horizontal direction. The structural timbers are made out of pine or chirr wood after properly seasoned and chemically treated to withstand its life against biting, fungus and termilte etc., 2.2 Fills Different types of preservative treated wooden splash bars, PVC bars are used depending on applications. Different types of afill materials with different shapes area available according to suited design of applications. Fill bars are designed to offer maximum splash surface and wetted surface resulting in a high heat transfer rate. 2.3 Water Distribution in Timber Boiler waterproof plywood [marine grade] / treated timber are used for hot water chamber. For uniform distribution box through which the water is equally distributed in the hot water basin. Basins are provide with combination metering orifices / diffusers which distribute water uniformly. 2.4 Fan Cylinder in Timber Fan cylinders designed in aero-dynamically the design allows close tolerance on fan blade tip clearance plus less interference of air passing through the tower. Fan cyclinder made by HDG Steel / Fiberglass reinforced polyester. 2.5 Nozzles in Timber The Target Nozzles used in the hot water chambers are designed to deliver required water evenly. The nozzle eliminates the need for a deck to provide complete water distribution throughout the fill area. It is highly resistant to temperature and weathering damage the water is distributed under gravity. 2.6 Louvers in Timber The standard cladding of profile corrugated asbestos cement sheet, the joints of which are lapped to shed water only inside the cooling tower. Louvers are supported and positioned by combination tower columns and louvers supports. 2.7 Drift Eliminators in Timber Specially designed eliminators from single pass pattern to 4 pass pattern of various materials are provided according to applications to minimize bleed of losses. Two pass herringbone drift eliminators trap entrained moisture causing it to drain into the cooling tower basin. 2.8 Mechanical Equipments in Timber The mechanical equipments are used in our cooling towers are specially designed for long lasting life. Multiblade fans are cast aluminim for smooth quiet operation, Low Noise, high volumes of air High efficiency, and low power consumption adjustable pitch blades are used for maximum utilization of applied horsepower. Fans are driven by an electric motor coupled to a spiral bebel gear box through a dynamically balanced tubular drive shaft. We are using special enclosed motors with weather proof and in IP-55 construction to withstand moist air stream. 2.9 The External Casing in Timber The External Casing is corrugated cement sheets fitted vertically and joints are lapped and sealed for water tightness. Corners are covered by absestos sheets. Also using FRP Sheets for External casing in Timber Cooling Towers. 2.10 Direct Drive Sytem in Timber These are lower and medium capacity cooling towers and upto 10 feet dia fan are supplied with multiblade cast aluminum adjustable pitch fan with M.S. Fabricated HDG Hub and SS Hardware. Motor provided with the system is special low RPM totally enclosed vertical Flange type is supplied with the cooling tower. The motor is totally weather proof in IP-55 construction suitable for heated and humid atmosphere. In the above model fan is directly coupled wiht the slow RPM motors [vertical flange mounted with sealed top and enlarged threaded shaft] 2.11 Reduction Gear Box Drive System in Timber Bigger capacity cooling towers are supplied with fan assembly driven through reduction gear reducer of spiral bevel type with the help of non-lubricated balanced drive shaft with flexible links. Fans are driven by an electric motor coupled to a gear box through a dynamically balanced tubular drive shaft. The compelete equipment will be supported on a single fabricated mild steel frame adequately weather proofed. Counter Flow Towers   Packaged Wooden Cross Flow Cooling Tower   Fan Less Natural Draft Cooling Towers Timber Cooling towers are usefull for chemical plants, air conditioning plants, induction furnace, injection moulding machine, chilling plants, oxygen plants. diesel generating sets and heat exchangers. And also for steel industries, cement industries, chemical industries, water effuluent treatment industries. Our Timber are designed for the highest efficiency at the lowest operating cost. Fans, gear boxes, fill and drift eliminators are optimized to deliver maximum cooling with minimum applied horse power for operating cost. Our Timber provide more wetted surface area for uniform water distribution and higher heat transfer rate. The structural timbers are made out of pine wood (or) chirr wood after properly seasoned and chemically treated to with stand its life against biting, fungus and termite etc., Different types of preservative treated wooden splash bars, PVC bars are used depending on applications. Different types of fill materials with different shapes are available according to suited design of applications. Fills are designed to offer maximum splash surface and wetted surface resulting in a high heat transfer rate. The wooden fills are supported on FRP/SS grids which assure positive & permanent positioning and to assure uniform water distribution. We export and having many clients at USA UAE Dubai and Abudhabi. Be Sociable, Share!

FRP cooling towers are very economically operating Cooling Tower, Since there is no fan or electric motor, there is no huge operating or maintenance cost involved in this Cooling Tower and also in Energy efficiency point of view, this is the best Payback Cooling Tower when comparing with other models. Specifications Simply says, in Fan less Cooling Towers the Hot water will be sprayed in the top of the Cooling Tower with spray nozzles into small droplets like mists and the droplets are crossed with the atmospheric wind flow to get the water cooled. Applications : This model Cooling Towers are water saving and pollution free, safety with environmental protection Method / Type : Sound free design. Fanless / Natural Draft : Since no fan, motor and gear box it is low noise Cooling Tower than any other low noise type Cooling Tower. Fan Motor Type : Since fan, motor and gear boxes are used, high noise and vibration. Advantages : FRP cooling towers of other model cooling towers are due to Fan, Motor, Gear box and Drive shaft and its vibrations. Since these models of Cooling Towers are not having Fan, motor, Gear boxes, this equipment has no trouble-some of noise & vibration.

• Brand Name: gireesh

We are offering dry cooling towers, gireesh cooling we are considered as one of the distinguished manufacturers and exporters of the dry cooling towers. Offered towers are wisely engineered and integrated with highly functional components. These are used for high temperature applications mainly for generators and process cooling. Finds its applicability across the chemical, process and pharmaceutical industries, our range of dry cooling towers is known for its robust construction and long lasting performance. Further, we offer our comprehensive stock to customer’s at most competitive prices. dry cooling towers are produced in forced draught and induced draught designs, and in single and multi-fan arrangements, depending customer specifications and requirements.

Dry Cooling Tower, Cooling Towers, Heatless Air Dryer, Air Dryers

Dry Cooling Tower is one of the latest model Cooling Tower. It is specially designed with copper or aluminium finned tube to increase the heat transfer area and these towers are particularly designed for water scarce areas. Since Dry Cooling Tower is functioning with Air-cooling Technology, there is no need of excess water evaporation or make up is required to operate the cooling Tower. And also, the ProcessEngine wateroil is directly taken from the system to Dry Cooling Tower. So the mid-Heat Exchanger is not required. When comparing with other type Cooling Towers these towers are zero maintenance and long-lasting.

Our fan less cooling towers design does not required any fan are fills, no maintenance like other cooling towers, non clock nozzle are easy to cleaning reduce spillage and evaporation loss. Hat dip galvanized structural and S.S fasteners increase the lifetime as well as the efficiency of the cooling tower it can be installed for any range of cooling application.

Adiabatic Cooling Tower unit built thus on scale back the body of water air temperature to the coil. This provides the shoppers with important reductions within the price|cost of capital opportunity cost of the cooler further as reductions within the cost of power consumption. associate electronic temperature controller is employed to regulate the fluid (process water) temperature inside rigorous tolerances. This temperature controller pulses the sprays of water onto the cooling pads to relinquish solely the minimum of adiabatic cooling of the body of water air needed for any given load and close condition.All style options area unit in to produce a protracted product life.  

We are Heat Transfer Equipments Pvt Ltd established in 1989 and also have many years experienced in the fields of Cooling Tower Manufacturer. We have member with (CTI USA) Cooling Technology Institute USA. Dry Cooling Towers are commonly used in the Power Plant, it is latest model cooling tower. A lots of power plants are cooled simply by air. Dry Cooling Tower is an equipment which is used dry cooler of defensive the working fluid from ecological revelation and contamination. There is no loss of water by evaporation because No water consumption in this type of cooling tower and also, we install the dry cooling tower in a right manner. Why Dry Cooling Tower? Dry cooling tower be able to a great extent speed up the Planning approvals process. Options are ever-increasing expenditure premiums are falling. Preservation expenses a great deal reduced Legislation is able to protect water provisions to power stations in droughts Also we experience of more than 23 years in the industry of cooling tower manufacturer Dry Cooling Tower Benefits are: Very economical in cost, Conserving significant amount of water, Minimizing environmental impact. How to Design Dry Cooling Tower?   We are designing the dry cooling tower as per the client requirements and we having 23 years experienced in cooling tower industry. We have well designed and develop the timber cooling tower for various industries. Our designing department is updated and very qualified engineers with designing knowledge and designing standards by cooling tower technology (CTI Membership).   If the thermal power plant is not located on the seaside or near a huge lake and if the water is either too exclusive to use a wet cooling tower, then the only cooling preference is using a dry cooling tower. A huge of water gets conserved on using dry cooling towers and Optimized cooling tower designing and develop using latest materials and latest technology construction methods.   In Dry cooling tower, Reduced yearly operating costs and it also No decomposition caused by air and this type of cooling tower performance ensures minimum ecological impact.

Portable Cooling Tower, engine oil cooler, Wire Wound Oil Cooler

• Type: Cooling Tower
• Material: FRP, RCC, Wooden
• Weight: 0-100kg, 100-200kg, 200-300kg
• Color: Blue, Light White
• Voltage: 110V, 220V, 380V, 440V.580V
• Condition: New
• Automatic Grade: Automatic, Manual
• Power: 1-3kw, 3-6kw, 6-9kw
• Driven Type: Electric
• Country of Origin: India
• Brand Name: Welltech Cooling Systems

Cooling tower is one type of heat transfer equipment. Process Water is cooled by ambient air by direct contact in wet cooling tower and indirect contact in dry cooling tower. We offer following in house design and fabricated cooling towers. Wet Cooling towers FRP cooling towers Timber Wooden cooling tower RCC cooling tower Dry cooling towers

Timber Cooling Tower, Natural Draft Cooling Tower, skid mounted cooling tower

Cooling Towers, Water Treatment Chemicals, Heat Exchangers

Cooling Towers, Heat Exchangers, industrial oil coolers, Oil Coolers

Cooling Tower Fans, Cooling Tower Motors, Cooling Tower Gear Box

Heat Exchanger

Cooling Towers, Air Cooled Condensers, Air Cooled Heat Exchanger