Industrial Valve Dealers in Rs Puram, Coimbatore

• White: Ivory

We are offering angle valve. Our angle valves are made of virgin abs and designed to save water. This unique design high grade finish will add luxuries feel to your toilet

• Material: MS
• Features: Sturdy construction, Accurate dimensions, Longer service life
• Size: 1/2 to 3 inch
• Pressure: 40 to 150 kg/cm2
• Temperature: 20 to 80 Deg C

• Features: Rust free, Easy to operate, Dimensional accuracy

We are offering kitz butterfly valve, aluminuim body butterfly valve ss 316 disc epdm rubber for upto 120 deg temp. kitz japan make butterfly valve leaver operated & gear operated.

• Usage: Release excess pressure
• Material: Aluminium
• Valve Size: 4inch
• Pressure: 9 bar
• Media: Air

This series solenoid valve adopts integral slot throttle structure. The valve hole is processed with special high precision finishing technique. The product has good performance and good change over with long service life, handsome shape and large airflow. It is widely applied to pneumatic system  .

Ibr, cast steel, casting, ductile, ci, sluicevalves, resilent gatevalves flanged end.with gear raising and non rising types.

We are dealers of pneumatic valves, pu hose ,pu fittings , pu valves, air blow gun (plastic & aluminium ).

We source direct as well as indirect raw materials only from the certified vendors present in the market. Our team of quality experts strictly checks the entire range against varied parameters. Keeping in consideration the latest standards, we are involved in supplying only high quality Loco Auto Drain Valve at reasonable prices.

Fast application of water in spray Pre-action and foam system Size: 50, 80, 100, 150 & 200 mm. (2″, 3″, 4″, 6″ & 8″) Cast iron body & cover Maximum service pressure 12 bar (175 PSI) Bronze Seat Flanged connection dimensions to ANSI B 16.1 Diaphragm operated with rubber to metal drip-tight positive sealing Reset without any tools Service without removal from line Easily trimmed for actuation by manual, remote solenoid valve & with dry or wet pilot Internal and external surfaces epoxy coated for extra protection  

• Body: CI / WCB / F.S / SS 304 / SS 316
• Internals: 13% Cr Steel, Gun metal / SS 304 /SS 316
• Actuator: Hand Wheel
• Size range: 15mm to 50mm (Class 800 & Class 150 )

A gate valve, also known as a sluice valve, is a valve that opens by lifting a round or rectangular gate/wedge out of the path of the fluid. The distinct feature of a gate valve is the sealing surfaces between the gate and seats are planar, so gate valves are often used when a straight-line flow of fluid and minimum restric¬tion is desired. The gate faces can form a wedge shape or they can be parallel. Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the Petroleum industry. A globe valve, different from ball valve, is a type of valve used for regulating flow in a pipe line, consisting of a movable disk-type element and a stationary ring seat in a generally spherical body. Globe valves are named for their spherical body shape with the two halves of the body being separated by an internal baffle. This has an opening that forms a seat onto which a movable plug can be screwed in to close (or shut) the valve.  Special Features: Compact Design Maintenance free Bolted bonnet, solid wedge gate, outside screw and yoke with rising/non rising stem of gate valve, Plug type disc and outside screw and yoke are provided ease of operation Wedge – Ground and lapped to precision Gland – Self aligning type Integral satellite seat and backseat Applications Cement & textile industry Fertilizer & chemical plants Petrochemical Industries & Refineries Steel plants Thermal, hydel and nuclear power plants Pulp & paper Industry Water & sewage treatment plants Food and beverage industries Pharmaceutical industry & Gas pipelines Etc. Constructional Features Body The body is the main pressure containing structure of the valve and the most easily identified as it forms the mass of the valve. It contains all of the valve's internal parts that will come in contact with the substance being controlled by the valve. The bonnet is connected to the body and provides the containment of the fluid, gas, or slurry that is being controlled. Bonnet The bonnet provides a leak proof closure for the valve body. The threaded section of the stem goes through a hole with matching threads in the bonnet. Globe valves may have a screw-in, union, or bolted bonnet. Screw-in bonnet is the simplest bonnet, offering a durable, pressure-tight seal. Wedge The closure member of the valve, wedge are connected to the stem which is slid or screwed up or down to throttle the flow. Wedge is typically of the balance or unbalanced type. Unbalanced wedge are solid and are used with smaller valves or with low pressure drops across the valve. The advantages are simpler design, with one possible leak path at the seat and usually lower cost. Balanced plugs have holes through the plug. Advantages include easier shut off as the plug does not have to overcome static forces. Stem The stem serves as a connector from the actuator to the inside of the valve and transmits this actuation force. Stems are either smooth for actuator controlled valves or threaded for manual valves. The smooth stems are surrounded by packing material to prevent leaking material from the valve. This packing is a wearable material and will have to be replaced during maintenance. Seat Ring The seat ring provides a stable, uniform and replaceable shut off surface. Seat rings are usually held in place by pressure from the fastening of the bonnet to the top of the body. This pushes the cage down on the lip of the seat ring and holds it firmly to the body of the valve. Seat rings may also be threaded and screwed into a thread cut in the same area of the body   Technical Specification Design and Manufacturing Standard • API 602 / BS 5352 Testing Standard • API 598 / BS 6755 Size range • 15mm to 50mm (Class 800 & Class 150 ) Operation • Manual hand Wheel • Electrical and Pneumatic linear cylinder with accessories

• Brand: APAXX
• U-PVC MATERIAL: ABS HANDLE

We are offering u pvc compact ball valve, u-pvc material, din standard, plastic inner ball, 12" to 4". Pn 16. Pp handle abs handle. Apply for cold water.

• Brand Name: Mercury
• Material: Aluminium (Body),Nitrile Rubber (Seal)
• Media: Air (Filtered 40 micro and lubricated)
• Model: NP Series
• Power Consumption: DC- 3W ; AC- 5VA Hold,7.5 VA Pickup
• Pressure Range: 2.5 - 10 bar

• Features: High efficiency, Optimal performance, Easy installation

• Feature: Smooth operation.

Pulp valves a wide variety of pulp valves which finds application in several paper and pulp industries for regulating the flow of semi solid material. Furthermore, these are also utilized in other areas like transportation, military, commercial and residential.

• Material: BRASS
• Brand Name: Techno
• Media: Gas, Water, Air
• Usage: Air
• Valve Size: 1/4TO 2 inch
• Place Of Origin: Delhi
• Model Name/Number: BRASS BALL VALVE
• Pressure: 10 BAR

• Features: Long life, High strength, Optimum finish

• Meterial of Condtruction: Cast iron
• Models: Screw type, Flange type, BOrewell type
• Maximum operating head: 10 m
• Available nominal size in mm screw: 40, 50, 65, 80, 100, 125, 150 mm
• “K” value: Less than 0.8 units
• Maximum Liquid Temperature: 33o C

Foot Valves C.R.I. energy efficient frictionless Foot Valves and Reflux Valves are basically swing type Non Return Valves. Foot Valves are available in screwed type construction and Reflux Valves have threaded portions at both the ends. They are specially designed to give an unrestricted smooth flow of water and thus to reduce the frictional losses to a minimum. The C.R.I. frictionless Foot Valve has 'K' value less than 0.8 and 'K' value for Reflux Valves are less than 0.5. Thereby it reduces additional load on prime mover and also gives more discharge. Foot Valve is placed at the lower end of the suction pipe of a centrifugal end suction pumpset to retain water in the pumpset casing and suction pipe to keep the pumpsets always in priming condition. Reflux and Non Return Valves are fitted generally in the delivery pipeline to avoid water hammer, up thrust and backspin effects in the pumping system. These can also be used anywhere in the suction line of which the bottom end is entered into a bore pipe or tube well. The pressure withstanding capacity of Reflux Valve and Non Return Valve are 1 bar and 15 bar respectively     Features        Suction path is almost straight to the pipe and hence frictional loss is very less.  Natural rubber flap totally prevents water leakage  Ruggedly built with graded cast Iron  Compact design and easy to install  Metal parts of Foot Valves are coated with bituminous paint to avoid rust formation  It increases water discharge upto 20% and reduces energy consumption upto 10%

• Construction: Direct acting, seat type.
• Mounting: Threaded port body
• Flow handling capacity (Nominal): Size 10 – 30 i/min, size 20 – 115 i/min
• Operating pressure: 315 bar
• Hydraulic medium: Mineral oil.
• Viscosity range: 10 cSt to 380 cSI.
• Fluid temperature range .: -20 °C to +70 °C

• Type: Automatic, Semi-Automatic