Plastering Machine Dealers in Coimbatore

Concrete Moulds are easily cast by using a tamping bar or a vibrating table. However air trapped in cement mortar paste can not be thus removed while casting cement mortar moulds. Easy method is to impart greater vibration of lesser amplitude to the mould while casting. This is achieved in a Vibrating Machine. Vibrating Machine is used for the preparation of mortar cubes for the determination of compression strength of ordinary and rapid hardening Portland cement, low heat Portland cement, Portland blast furnace cement and high alumina cements.   Specifications: The machine consists of a vibrating frame assembly and an electric motor mounted on a sturdy base. The complete frame assembly consists of a vice to hold a 7.06cm cube mould and two studs threaded at top and a hopper to feed the sample in the mould. This assembly is supported on four springs and has an in built rotating shaft which rotates eccentrically and thus imparts vibrations to the entire frame. A balance weight is an integral bottom part of the frame. The centre of gravity of the assembly is brought to the centre of the eccentric shaft or within a distance of 25mm below it. The electric motor drives the shaft of the frame and thus imparts required vibrations to the mould. The frequency of vibration is 12000 ± 400 vibration per minute. Supplied complete with a 7.06cm cube mould and loose base plate, a time switch 0-5mins x 1 min and certificate of vibration.

• Type: Wall / Ceiling
• Warranty: 1 Year
• Condition: New
• Speciality: Optimum strength
• Usage: Industrial
• Efficiency: Consistent
• Feature: High strength

• Type: Cement Production Machinery
• Size: 1350 × 800 × 500 mm
• Capacity: 450 Square Meters/8 Hours

Our wall plastering machine is suitable for the construction industry. It makes rendering easier, faster and effortless Compared with manual application. Our plastering machine also can work with different mortar which bring it to a Smooth, flat finish with adjustable thickness to suit each application. Features Our machine make use of the conveyor taking mortar forwardly and upwardly, It can plaster to the roof by all means. The conveyor can take mortar or stop in any position by hand control. The spatula can change the angle at angle, plastering the wall by rising large angle, sharpening and pressing by angle decline, thus guaranteed zero vertical error and plastering to the roof. The hydraulic telescopic rod can make the machine installation in 10 second and the chassis is not stress. When you want to move the machine you just can release the rod as moving. The main rod declined by gravitation, the bottom life automatically. This kind of installation is the most fast and stable one. The width of spatula is designed according the width of the door, The machine can go into the room freely. It can reach the inside corner and the exposed corner. There are two min-vibrators behind the spatula, thus you need not to worry about Hollowing and adhesion. Our machine adopted the universal wheel after sealing and it can easily move to any place you like. Safe Protection If the electrical machinery reverse, the machine can cut the power automatically to protect the wirerope from mass. Just commutate the two direction switch. If the machine got stuck when declining, the power will be butting automatically to avoid wirerope came messy. All the active parts and tighten bolts have a high degree of anti-rust treatment. All the bearings have been multiple sealed up. The front heavier design make the machine do not backward also if the hydraulic cylinder became flexible.

The Auto Wall Plastering Machine, supplied by us, is manufactured using premium quality materials like stainless steel, aluminium alloy, etc. Our machine is reckoned for its hassle-free performance and enhanced productivity (370 m2/ day).

• Material: Construction Equipment
• Usage/Application: Plastering
• Brand/Make: SCORPION
• Item Weight Kgs: 450
• I Deal In: New Only
• Minimum Order Quantity: 1 Piece

• Capacity: 50 - 300 TPH
• Brand Name: Nesans
• Condition: New
• Customized: Yes
• Rotor Speed: 3.2 rpm
• Hydrocyclone Size: 75 micro meter (200 mesh)
• Dewatering Screen Size: 2.4 m x 1.2 m (8 x 4 inch)
• Dewatering Screen Material: Polyurethane
• Model No: SWE1000

The Plastering Machine, which we deliver, is largely appreciated for its specially designed plastering height control mechanism that enables to plaster wall surface under the beam, below and above window corner.

auto wall plastering machine

Wall Rendering Machine, Automatic Wall Rendering Machine

sponge assembly machine, CNC Machines, Special Purpose Machines