Earth Products India Pvt Ltd. Okhla, Delhi

Recommended for strong motion earthquake survey & industrial applications requiring

Medical DITI is a noninvasive adjunctive diagnostic technique that allows the examiner to visualise and quantify changes in skin surface temperature. An infrared scanning device is used to convert infrared radiation emitted from the skin surface into electrical impulses that are visualised in colour on a monitor.

Resipod is a fully integrated 4-point Wenner probe, designed to measure the electrical resistivity of concrete in a completely non-destructive test. It is the most accurate instrument available, extremely fast and stable and packaged in a robust, waterproof housing designed to operate in a demanding site environment.

The Profoscope+ is a fully integrated rebar locator with data storage. To increase the efficiency on the construction site this enhancement of the Profoscope not only offers real time visualization of rebars, but also automatic data collection.

The Profometer 5+ cover meter is a sophisticated device for the non destructive location of rebars and for the measurement of concrete cover and bar diameters, using the eddy current principle with pulse induction as the measuring method. As well as detecting the rebar diameter accurately to the millimeter by only one measuring procedure, the cover meter Profometer 5+ offers the transmission of the measured data to a PC.

Pull-off testing is one of the most widely used test methods in the construction industry. This is reflected in the huge number of standards dedicated to the method.

PIT performs Low Strain integrity testing, also called Sonic Echo or Pulse Echo Testing. The PIT may be used for auger cast-in-place (CFA) piles, drilled shafts, driven concrete piles, concrete filled pipes and timber piles.

PIR: Automated Monitoring Equipment for Augered Cast-In-Place (ACIP), Continuous Flight Auger (CFA) and Drilled Displacement Piles. Meets Deep Foundations Institute Augered Cast-in-Place Manual guidelines. Complies with FHWA GEC no. 8 requirements for ACIP piles. Easy to achieve Quality Control during construction.

Pile Driving Analyzers acquire data from acceleration and strain sensors attached to the foundation, and process these signals as the foundation element is impacted by a pile driving hammer or other suitable drop weight. This process is called High Strain Dynamic Test, and may take the form of Dynamic Pile Monitoring or of a Dynamic Load Test.

Excess moisture in concrete can be fatal to a floor covering installation. To prevent mildew and major damage, the flooring industry requires smart solutions to check surfaces for moisture prior to installing floor coverings or coatings. The Hygropin moisture meter offers the perfect solution to identify and monitor moisture in concrete.

The E-Sax is used by piling inspectors everywhere to generate a complete Pile Driving Log, including: * Pile name * Start and stop driving times * Blow count versus depth * Blows per minute * Final equivalent blow count for the last 20 blows * Stroke of open end diesel hammers * Potential energy of open end diesel hammers

Evaluate and observe structural safety and integrity as well as safe operation, Assess and compare the behavior against the seismic design criteria, Develop and improve emergency and safety measures as well as awareness, Applications: Bridge, Building, Foundation, Dam, Slope

The Schmidt Hammer Digi-Schmidt was developed for the non destructive measurement of the concrete compressive strength and controlling the uniform concrete quality.

The Cross-Hole Analyzer (CHA) uses Crosshole Sonic Logging technology to determine the quality and consistency of concrete between pairs of PVC or steel tubes pre-installed in drilled shafts, slurry walls, bored piles, cast-in-situ piles and other types of concrete foundations.

Corrosion Analysis allows the contractor to limit the maintenance tasks on reinforced concrete to the areas where it is really required. The Canin+ is the fastest instrument for corrosion analysis, offering a practical, cost-effective approach to the investigation of reinforced concrete.

Features More economical and practical China patented product. It can replace the same type foreign made instrument , - Size is small. The measuring results can be printed directly. Thus, ease the onsite detection. - Affordable, high accuracy, long life, and not subject to the life of use problem as mechanical concrete hammer did.

The PANDA automatic hammer is an option that can be added to the PANDA® (1st or 2nd generation). The goal is to substitute it for manual hammering in order to increase yields, to facilitate large numbers of tests, and to help conduct deep surveys.

The Acoustic Concrete Tester determines the thickness of structural elements such as concrete pavements, slabs, retaining walls, tunnel liners, foundation footings, and more. In addition, the ACT may identify defects such as delaminations, spalls and horizontal flaws. The ACT tests structures as thin as 75 mm and as thick as 600 mm.

Strain Transducers and Accelerometers manufactured by Pile Dynamics collect the essential data for use with the Pile Driving Analyzer(PDA) and SPT Analyzer.

Sensors are quickly bolted to any type of foundation, usually about 2 to 3 diameters below the top. Strain transducers are attached symmetrically to account for bending effects. Accelerometers should be attached near the strain transducers.