Electronic Test Instruments Dealers in Shahdara, Delhi

Automatic Calibration: WPH meter is capable of calibrating up to 2 points using USA or NIST pH standard buffer. Press CAL key to enter calibration mode and immerse pH electrode into indicated calibration solution, press ENTER key and meter is automatically calibrated. Auto-Buffer Recognition: During Calibration, If The Calibration Solution Does Not Match The Meter's Indicated Value, An ERROR Message Is Displayed. View Electrode Slope: After Calibration, The Percentage Slope Of The Electrode Is Displayed Before The Meter Returns To Measurement Mode. Per The Slope Value, You Decides Whether To Change The Ph Electrode. Automatic Temperature Compensation: Using The Supplied Temperature Probe, The Temperature Value Is Displayed On The Screen. The Meter Provides Manual Or Automatic Temperature Compensation Mode For Optimum Accuracy Under Variable Temperature Conditions. Fluid Resistant Housing And Swivel Electrode Holder: The integrated plastic housing and keypad is sealed to protect against accidental spills and splashes. The electrode holder arm is rapidly switched to both sides and swivels and articulates for convenient use and positioning.

• Driven Type: Electric
• Phase: Single Phase
• Warranty: 1 Year
• Certifications: CE Certified
• Application: Home & Industrial
• Mounting Type: Wall Mounting

• Brand Name: Labman
• Application: Laboratory
• Accuracy (Percent): LCD
• Condition: New
• Material: Plastic
• Conductivity: +1%
• Display: LCD

      ' Portable Hardness Tester                                                                                                       Portable Rockwell Hardness Tester model MRP- 1 is able To test part where bench type Model is not useful. This machine is quite handy for product testing of crank shafts, cylinder blocks, industrial knives, liner and assembliese. This can be used for testing the hardnessof both inside and outsite of surface testing of pipes, bushing, ball bearing rings or other complicated parts. This models can be used in any direction Without affecting the accuracy. Technical Data Maximum test height  : 110mmThroat capacity            : 55mmWeight (Approx.)          : 1. 55 kgStanderd Accessories Flat anvil @ 25mm    : 1 No.V- anvil@ 25mm        : 1 No.Test block HRC          : 1 No.Test block HRB          :  No.Diamond indentor      : 1 No.1/ 16” ball indentor     : 1 No.Steel Ball @ 1/16”      : 5 Nos.Carry case                  : 1 No.Portable Rockwell Hardness Tester is developed to meet the demands of a light weight instrument which can be used to carry out by a universally recognised method of hardness testing.Rockwell Method : This hardness tester can be used in variety of applications and is readily adjustable to a wide range of sizes and shapes which are difficult to test in a standard table model hardness tester.The machione os designed for carrying out Rockwell tests comparable to table model hardness tester because, the basic things, such as shape of penetration, measurement and loads are same in both systems.The photograph on the back side gives the general arrangement of the hardness tester.The system carries a weight bar (8) pivoted at central point. When the load is applied by the loading screw (9), at one end of this weigh bar, it is deflected and theother end of this bar carrying penetrator forces down into the testspecimen. This deflection of weight bar which is proportional to the applied load is indication of the loading dial indicator (11). Besides this loading dial indicator, there is one penetration measuring indicator(14) which masures the actual penetration of the penterator into the test specimen. The hardness value of the specimen is read directly on this indicator. The frame carries two adjusting screws and gear train. By roating the knurled knob the distance between the penetrator and the support-anvil can be adjusted. Upper clamp Lower clamp Support anvil Adjusting screws Knurled Knob Penetrator Penetrator tightening screw        ' Portable Hardness Tester                                                                                                       Portable Rockwell Hardness Tester model MRP- 1 is able To test part where bench type Model is not useful. This machine is quite handy for product testing of crank shafts, cylinder blocks, industrial knives, liner and assembliese. This can be used for testing the hardnessof both inside and outsite of surface testing of pipes, bushing, ball bearing rings or other complicated parts. This models can be used in any direction Without affecting the accuracy. Technical Data Maximum test height  : 110mmThroat capacity            : 55mmWeight (Approx.)          : 1. 55 kgStanderd Accessories Flat anvil @ 25mm    : 1 No.V- anvil@ 25mm        : 1 No.Test block HRC          : 1 No.Test block HRB          :  No.Diamond indentor      : 1 No.1/ 16” ball indentor     : 1 No.Steel Ball @ 1/16”      : 5 Nos.Carry case                  : 1 No.Portable Rockwell Hardness Tester is developed to meet the demands of a light weight instrument which can be used to carry out by a universally recognised method of hardness testing.Rockwell Method : This hardness tester can be used in variety of applications and is readily adjustable to a wide range of sizes and shapes which are difficult to test in a standard table model hardness tester.The machione os designed for carrying out Rockwell tests comparable to table model hardness tester because, the basic things, such as shape of penetration, measurement and loads are same in both systems.The photograph on the back side gives the general arrangement of the hardness tester.The system carries a weight bar (8) pivoted at central point. When the load is applied by the loading screw (9), at one end of this weigh bar, it is deflected and theother end of this bar carrying penetrator forces down into the testspecimen. This deflection of weight bar which is proportional to the applied load is indication of the loading dial indicator (11). Besides this loading dial indicator, there is one penetration measuring indicator(14) which masures the actual penetration of the penterator into the test specimen. The hardness value of the specimen is read directly on this indicator. The frame carries two adjusting screws and gear train. By roating the knurled knob the distance between the penetrator and the support-anvil can be adjusted. Upper clamp Lower clamp Support anvil Adjusting screws Knurled Knob Penetrator Penetrator tightening screw  Weight barLoading Screw HandleLoading dial indicatorIndocator seat supportIndicator seat Penetration measuring indicator   1) Select proper penetrator (6) depending upon the material to be tested.2) Take precaution so thet the penetrator does not project beyond the Upper clamp.    (1) For this, the loading screw (9) should be sufficiently taken back.3) place the test specimen securely on suitable anvil(3).4) Clamp test specimen firmly between upper clamp (1) and support anvil     (3) by rotating the knurled knob (5) on the lower clamp     (2) do not apply extra pressure5) Check zero setting load indicator (11) rotate bezel to bring pointer over small black    dot for zero load.6) Apply 10 kgf (98.07 N). major load screw (9) in clockwise direction such that the pointer    on the load indentor (11) comes on set position. 7) Check zero setting of penetrator indicator (14) Rotate bezel to bring pointer to ‘O’ on     the black scale. 8) For ‘C’ scale use diamond penetrator against load of 150 kgf (1471 N) and for ‘A’    scale use same diamond penetrator against a load of 60 kgf (588.4 N). For ‘B’ scale    use 1/16 ball penetrator against a load of 100 kgf (980.7 N). 9) Take off major load by turning the loading screw in anticlockwise direction, such that     only minor load of 10 kgf. (98.07) remains in action – (pointer back to ‘set’ position). 10) Hardness value in Rockwell scale is directly indicated on the penetrator indicator      (14). Read of number on black scale is diamond penetrator.              Read off number on red scale is ball penetrator11) Release load completely by taking back the loading screw 12) Turn the knurled knob (5) in anticlockwise direction to loosen clamp and thus  the test speciman.    

• Material: Plastic
• Power Source: Battery
• Country of Origin: Made in India
• Application: Optical power meter
• Brand Name: Optivision
• Model Name/Number: 01

• Brand: MADE IN INDIA
• Usage/Application: Industrial
• Model Name/Number: SLD
• Display: LCD
• Measuring Frequency: 10

• Country of Origin: Made in India
• Brand: Henrich
• Model: Mini Powe Meter
• Material: metal
• Usage: Industrial, Optic Fiber
• Display Range: +2db

We offer world class Digital Turbidity Meter that is widely used in different kinds of laboratory applications and experiments. We offer highly precise and accurate Digital Turbidity Meters that are equipped with the best spares and accessories that make them the best available in the market. The easy availability of our high performing meter at competitive prices makes us the best Digital Turbidity Meter manufacturer and supplier from New Delhi. Main Components : Turbidity Meter3-1/2 digit LED displayRange 0 to 1000 NTU/JTU Technical Details : 0 - 10,000 NTUPrinciple of Operation : NephelometricRatio (Color Correction) : Full Time ON or OFFAccuracy :± 2% of reading plus 0.01 NTU (0 to 1000 NTU)± 5% of reading (1000 to 4000 NTU)± 10% of reading (4000 to 10,000 NTU)

• Features: Hassle free usage, Easy installation, Exact result , Precise design

• Voltage: 10 ADC
• Frequency: 1000 kHz
• Display Type: Digital
• Model Name/Number: MAS830L
• Length: 185 mm
• Height: 40-50 mm
• Battery: 9-10V
• Brand: Unity

• Display Type: Digital
• Shape: Square
• Voltage: 500 V
• Brand: Mark
• Usage/Application: Industrial
• Dimension: 72X72 mm(LxW)
• Phase: Single Phase
• Current: 30 Amp
• Frequency: 50 Hz

• Brand Name: KHETAAN
• Body Material: Plastic
• Country of Origin: India
• Color: BLACK

METER details :- Usage/Application : Electric Vehicle Voltage : 48/60/72 Color : Black Weight : 300-500 Gm Outer Material : Plastic Display : Digital Packaging Type : Box

Digital Milli Ohm Meter, Three Color Pad Printing Machine

• Type: Universal Ic Tester
• Certification: ISO 9001:2008 Certified
• Weight: 0-200gm, 200-400gm
• Color: Brown, Grey, Light White, White
• Voltage: 0-6VDC, 12-18VDC, 18-24VDC, 6-12VDC
• Condition: New, Used
• Application: Ic Testing
• Driven Type: Battery, Electric
• Warranty: 1yr, 2yrs
• Automation Grade: Automatic, Fully Automatic, Manual, Semi Automatic

laser power meter, Laser Pointer, laser measuring equipment

Car battery tester, Motorcycle Battery, Traction Batteries

Power Factor Meter, electrical measuring instruments, digital earth tester

We Offer a Large Assortment of Excellent Quality Magnetic Flow Meter that is Used to Measure the Flow Rate of the Conducting Slurries and Liquids Flowing in the Closed Pipes. Our Insertion Magnetic Flow Meter is Manufactured from the Finest Quality Raw Materials that are Sourced from the Authentic Vendors. Easy to Install, Dimensional Accuracy and Long Lasting Trouble Free Performance are the Unique Characteristics of Our Insertion Magnetic Flow Meter. We have Carved a Niche as One of the Ecstatic Digital Magnetic Flow Meter Suppliers Based in India.

electronis energy meters, main switch change over

industrial data logger

frequency meters, Voltmeters, Ammeters, Current Transformers

million megohm meter

Energy Meters, chalks, Current Transformers

laser power meter, Low Noise Laser Diode, helium neon laser

PVC, lamination products, BOPP Film, packing films

Data Logger, Industrial Cloud Gateway, measurement instrument

Data Logic Linear Automation Scanner, 2D Barcode Reader