Flat Bar Dealers in Wazirpur, Delhi

We are offering hrap flat bars. Ambica steels's stainless steel flat bars are used widely in various structural & industrial applications.

• Length: 2 metres – 6 metres ( 8 feet to 20 feet)
• Size range: Width: 40 mm to 100 mm, Thickness: 4.76 mm to 25.4 mm
• Size Tolerances: h11 and ASTM A 484
• Length Tolerance: Available in special cut to length bars in tolerance -0/+10 mm (-0/+0.5 inch)
• Surface Finish: Cold Drawn and Belt Polished Condition
• Heat Treatment: Solution Annealed
• Grades: AISI: 303, 304L, 316L, 316Ti, 321   DIN: 1.4305, 1.4307, 1.4404, 1.4571, 1.4541

Drawing is a metal working process in which metal is drawn through a die to reduce its diameter and increase its length, it stretches thinner, into a desired shape and thickness. It uses tensile forces to stretch metal. Drawing is usually done at room temperature, thus classified as a cold working process.It also alters the mechanical properties of the metal. Cold drawn cross-sections are more precise and have a better surface finish than hot extruded parts.The cold drawing process for steel bars and wire- Coating: The surface of the bar or coil is coated with a drawing lubricant to produce cold drawing. Pointing: The end of the workpiece is reduced or pointed by extruding so that it can pass freely through the die. The pointing end is then placed in grips and the rest of the workpiece is pulled through the die. Cold Drawing: The process in which the pointed end of the bar or coil is passed through the die where it enters a gripping device of the drawing machine. The drawing machine draws the remaining unreduced section of the bar through the die. The die reduces the cross sectional area of the original bar increases the length of the original product and shapes the profile of the product. Finished Product: The final product being drawn is at room temperature i.e cold drawn which exhibits a bright and polished finish, improved machining characteristics, increased mechanical properties, precise and uniform dimensional tolerances. Multi-Pass Drawing: In order to produce the desired shape and tolerances, the cold drawing of complex shapes may require that each bar/coil be drawn several times. This process is called multi-pass drawing and involves drawing through smaller and smaller die openings. The material is generally annealed between each pass while drawing to remove cold work and to increase ductility. Annealing: It is a heat treatment process generally used to soften the material being drawn, to remove internal stresses in the product or modify the mechanical properties, its microstructure, and the machining characteristics of the steel.Annealing may be used before, during i.e between passes or after the cold drawing operation, depending on the desired characteristics of the finished product & material requirements.    

• Length: 2 meters - 7 meters ( 8 feet to 24 feet)
• Surface Finish: Hot Rolled Annealed & Pickled (HRAP) Condition
• Carbon: <= 0.03
• Silicon: 1
• Manganese: <= 2
• Sulphur: 0.030
• Phosphorus: <= 0.045
• Nickel: 8 - 11
• Chromium: 18 - 20
• Niobium: Not required
• N: <= 0.10
• Size Range: 38x10 mm to 150x25 mm
• Size Tolerances: EN 10058 and ASTM A 484
• Length Tolerance: Available in special cut to length bars in tolerance -0/+10 mm (-0+0.5 inch)
• Heat Treatment: Annealed, Solution Annealed
• Grades: AISI: 303, 304L, 316L, 316Ti, 321,410, 416, 420, 630/17-4ph

Ambica Steels's Stainless Steel Flat Bars are used widely in various Structural & Industrial applications.

We are offering stainless steel flat bar. Stainless steel flat bars of all grade (hot rolled and cold rolled)

Size Range Size (mm) Size (inch) Thickness (mm) Thickness (in Inches) 25mm 1" 5 mm to 20 mm 15" - 45" 30 mm 1-316" 5 mm to 20 mm 15" - 45" 32mm 1-14" 6 mm to 20 mm 14" - 45" 35mm 1-38" 5 mm to 20 mm 15" - 45" 40mm 1-47" 5 mm to 25 mm 15" - 1" 45mm 1-79" 5 mm to 25 mm 15" - 1" 50mm 2" 5 mm to 32 mm 15" - 1-14" 60mm 2-38" 5 mm to 35 mm 15" - 1-38" 63mm 2-12" 10 mm to 30 mm 38" - 1-316" 65mm 2-59" 10 mm to 30 mm 38" - 1-316" 75mm 3" 8 mm to 25 mm 516" - 1" 80mm 3-18" 8 mm to 25 mm 516" - 1" 100mm 4" 8 mm to 25mm 516" - 1" 150mm 6" 8 mm to 20mm 516" - 45"

We are offering flat bars. Our hrap flat bar is the choice of select engineering, architectural and fabrication agencies in wide ranging applications. We offer hrap flats in standard as well as customized grades and dimensions for specific uses. Our hrap flats are manufactured under rigorous quality control procedures using premium inputs and finished to a high level.

Stainless steel strip or steel flat bar is available in grades 304, 304L, 316 and 316L, slit and hot rolled. Available in lengths of 4 and 6 meters and thicknesses t 3 / m 30 mm.

We are well known for supplying of wide variety of Flat Bars.

Stainless Steel Products, Stainless Steel Bars, Heat Treatment Service

Steel Flat Bars, Iron, Stainless Steel Products, steel Products

Stainless Steel Flat Bar, stainless steel hexagonal bar