Back Back
Oxygen Gas Generator
Procurement of the product from us is profitable, as we can provide it in wholesale any time of the year and ensure delivery is done on the postulated time. To ensure complete safety of the products from diverse damaging factors such as rain, dust, sunlight, moisture, etc., we keep the lot in our capacious warehouse before dispatch.
Brand Name : Indranil Exports
Condition : New, Good
Type : Gas Generator
...more
Nitrogen Gas Generators, Psa Nitrogen Gas Generators
1No / 5 -6 Nos. Piece (MOQ)
We are offering nitrogen gas generators, psa nitrogen gas generators. psa nitrogen gas generators : the nitrogen generator produces nitrogen gas from atmospheric air using sieves separation technique. It uses carbon molecular sieves which has ability to preferentially absorb oxygen from air . Our gas generators provides higher efficiency of gas separation . capacity: 1 nm3/hr to 1500 nm3/hr purity: 95% to 99.9999% pressure: up to 10-bar without nitrogen booster compressor dew point: (-) 40˚c to (-) 80˚c cost of generation: indian rupees: rs. 3/- per nm3 us $: 6 cents per nm3 psa principle : nitrogen gas generator consists of two beds filled with carbon molecular sieves . When compressed air is passed , nitrogen comes out as a product gas from one bed while the other bed is simultaneously regenerated by depressurization to atmospheric pressure . This process of gas separation is called “pressure swing adsorption”(psa) psa nitrogen gas generator produces nitrogen gas from atmospheric air by psa (pressure swing adsorption) technology. Psa technique is a simple & reliable process of separation of nitrogen from compressed atmospheric air by adsorption of oxygen over a bed of carbon molecular sieves (cms). Cms is an adsorbent having infinite number of small pores. The diameter of the “bottle necks” is in the same range as those of the molecules. Thus when cms is used in the psa process, an oxygen molecule, having a smaller diameter than a nitrogen molecule traps in to the pores. Therefore the nitrogen is recovered to a high degree while almost all the oxygen is adsorbed. process:- the production of nitrogen gas from atmospheric air is based on pressure swing absorption (psa) principle by adsorption of oxygen gas using a special grade of imported carbon molecular sieves (cms). Atmospheric air is compressed by an air compressor to a pressure of 7.5 kg/cm2g and cooled to ambient temperature in a shell and tube type heat exchanger. The condensed moisture shall be drain out automatically from air receiver by automatic drain valve (adt). The compressed air at ambient temperature is passed through psa module packed with activated alumina and special grade of carbon molecular sieves. The production of nitrogen from air by psa technology is largely based on the kinetic separation. Oxygen that is smaller in size (kinetic diameter 3.46 a0) diffuses much faster than nitrogen (kinetic diameter 3.64 a0) and hence oxygen gets adsorbed in carbon molecular sieves and nitrogen is collected as the high-pressure product. The entire operation is fully automatic and controlled by a combination of sequence programmer and quick change over valves. Nitrogen gas of desired purity at 5.5 kg/cm2g pressure and having a dew point of (-) 40 degree celsius is produced by the psa unit, now flows to a surge vessel to balance the fluctuations in pressure and concentration. Now the gas can be stored in a storage tank at 5.5 kg/cm2g pressure from where it can be made available for process application. The storage tank can selected of any desired capacity as per peak hours demand for nitrogen gas or power interruptions. This system is fully automatic and need not any special operator for operation. Once it is started it generates nitrogen at constant flow rate and at constant pressure. Further the produced nitrogen gas can be boosted to high pressures by providing any reliable booster compressors up to desired pressure. We offer various models of nitrogen gas plant and selection is based on the purity required. advantages : - automatic start –up time is only 5- minutes - nitrogen gas supply is always under your control. - self- contained skid mounted units for easy site installation . -very low maintenance costs. -very high reliability to run un-attended plant. -carbon molecular sieves life is minimum 10-12 years in normal working condition and in most cases it lasted the while life time of gas generator. nitrogen capacity: we are manufacturing psa nitrogen gas generators capacity of 1,2,5,10,15, 20 25.40 , 50, 60, 70,80, 100, 125,150, 175 , 200 ,250, 300 ,350 400, 500 ,600 ,800 ,1000 & 1250 & 1500 nm3/hr , purity 95 % to 99.9999% . Pressure up to 10 bar without nitrogen booster compressor . Dew point (-) 40 deg c to (-) 80 deg c. We are also manufacturing psa nitrogen gas generators as per yours specific requirements. we are exporting psa nitrogen gas generators to various countries such as middle east , bangladesh , nepal , brazil, south america, africa , india & other countries. We have our after sales & service teams we are providing after sales & service to all over the world including india nitrogen pressure: standard nitrogen generator produces nitrogen at 5.5 kg /cm 2 g pressure. This pressure comes automatically as feed air pressure to the psa unit is around 7.5kg /cm2g. However , by increasing feed air pressure to 13 kg/cm2g. Nitrogen can be produced even at 10 kg / cm2g. But at high pressure operation , depressurization losses during regeneration are higher, which results in high operation costs. it is most economical to run nitrogen generators at 7.5 kg/ cm2g pressure and produce nitrogen at 5.5 kg/cm2g pressure . However by increasing feed air pressure to 13 kg/cm2g. Nitrogen can be produced even at 10 kg / cm2g. If nitrogen is needed at higher pressure , we can provide a nitrogen booster compressor after the gas generators .by this addition , it is possible to compress nitrogen gas to any desired high pressure. advantages of psa nitrogen gas generators: 1. Self- contained skid mounted units for easy site installation. 2.very low maintenance costs. 3. Very high reliability to run un-attended for months & months. 4. Carbon molecular sieves life is minimum 10-12 years in normal working condition & in most cases it is whole life of the psa nitrogen gas generators. skid mounted psa nitrogen gas generator systems consists of : 1.air compressors system with cooler. 2.air receiver cum moisture separator with automatic drain and high- level alarm. 3.air dryer / refrigerated dryer to make air-sub -saturated 4.coarsed and fine filter for oil and solid removal 5. Ultra fine filters 6.twin tower psa unit 7. Surge vessel 8. N2 gas tanks 9. Booster pump if required for higher discharge pressure of nitrogen gas 10. Microprocessor control panel we offer various models of nitrogen gas plant and selection is based on the purity required which are as follows : ms model : 1. Ms-l 2. Ms-h 1. Ms-l (gas composition ) : nitrogen 98-99 % oxygen 0.1- 2 % hydrogen nil dew point (-)40ºc to (-)80ºc applications : - as inert gas in chemical industries - food & pharmaceutical industries - for fire control in coal mines etc. 1.ms-h ( gas composition ) : nitrogen 99.5 -99.999% oxygen 10 ppm- 500ppm hydrogen nil dew point (-)60ºc to (-)80ºc applications : - as inert gas in chemical - food pharmaceutical industries - heat treatment furnaces - electronic, synthetic fiber, industries. deoxo model applications manufacturer and exporter of deoxo model. This model is commonly used in metallurgical industries for providing oxygen free nitrogen for heat treatment furnaces. Here, the oxygen is less than 1-ppm and but hydrogen is around 0.5 to 1% which is desirable as reducing constituent in most of heat treatment applications. “ms” models can also be converted into “dx” model by adding palladium deoxo reactor and gas drying unit. “dx” model is also applicable in chemical as well electronic industries. gas composition : nitrogen 99.9999% oxygen 1 to 3ppm(max) hydrogen 0.5% or more dew point (-)40ºc to (-)80ºc applications : - as inert gas in chemical & pharmaceutical industries. - in applications where oxygen impurity is not acceptable. cu deoxo model cu deoxo model contains an extra nitrogen purification module based on copper deoxo catalyst. This model finds application in synthetic fiber, optical cables & electronic industries. Running cost of this unit is slightly higher because it produces very pure nitrogen gas i.e free from oxygen and hydrogen as well. It is applicable where hydrogen contents are detrimental to the process. gas composition: nitrogen 99.9999% oxygen 1 ppm (max) hydrogen nil dew point (-)40ºc to (-)80ºc applications: - as inert gas in electronic, synthetic fiber, - hitech industries where one needs ultra high purity. industrial uses of nitrogen gas generators : nitrogen generators are extensively used in the following industries: • chemical and petrochemicals industries for inertization, blanketing and purging requirements • ferrous and non-ferrous metallurgical industries for protective atmosphere during annealing, sintering and carburizing processes • pharmaceutical industries for inert atmosphere for reactions and for inert conveying • cement industries for fire prevention and fire fighting in coal mill silos • food packaging and processing industries for extending the shelf life of food products • glass industries for prevention of oxidation during manufacturing • transportation sector for nitrogen tire filling to extend tire life and increased safety please send your enquiry with the following details to us : 1.flow rate of nitrogen gas generator required = nm3. Hr 2.purity of nitrogen gas required = % 3. Discharge pressure of out let of nitrogen gas required = kg/ cm2 4.air compressore type = screw compressure oil cooled type or oil free type 5. Make of air compressore required 6. Any nitrogen gas storge tank required = m3 7. Please confirm us when you are going to finalization the order . we will submit our offer at the earliest to you. psa nitrogen gas generators : the nitrogen generator produces nitrogen gas from atmospheric air using sieves separation technique. It uses carbon molecular sieves which has ability to preferentially absorb oxygen from air . Our gas generators provides higher efficiency of gas separation . capacity: 1 nm3/hr to 1500 nm3/hr purity: 95% to 99.9999% pressure: up to 10-bar without nitrogen booster compressor dew point: (-) 40˚c to (-) 80˚c cost of generation: indian rupees: rs. 3/- per nm3 us $: 6 cents per nm3 psa principle : nitrogen gas generator consists of two beds filled with carbon molecular sieves . When compressed air is passed , nitrogen comes out as a product gas from one bed while the other bed is simultaneously regenerated by depressurization to atmospheric pressure . This process of gas separation is called “pressure swing adsorption”(psa) psa nitrogen gas generator produces nitrogen gas from atmospheric air by psa (pressure swing adsorption) technology. Psa technique is a simple & reliable process of separation of nitrogen from compressed atmospheric air by adsorption of oxygen over a bed of carbon molecular sieves (cms). Cms is an adsorbent having infinite number of small pores. The diameter of the “bottle necks” is in the same range as those of the molecules. Thus when cms is used in the psa process, an oxygen molecule, having a smaller diameter than a nitrogen molecule traps in to the pores. Therefore the nitrogen is recovered to a high degree while almost all the oxygen is adsorbed. process:- the production of nitrogen gas from atmospheric air is based on pressure swing absorption (psa) principle by adsorption of oxygen gas using a special grade of imported carbon molecular sieves (cms). Atmospheric air is compressed by an air compressor to a pressure of 7.5 kg/cm2g and cooled to ambient temperature in a shell and tube type heat exchanger. The condensed moisture shall be drain out automatically from air receiver by automatic drain valve (adt). The compressed air at ambient temperature is passed through psa module packed with activated alumina and special grade of carbon molecular sieves. The production of nitrogen from air by psa technology is largely based on the kinetic separation. Oxygen that is smaller in size (kinetic diameter 3.46 a0) diffuses much faster than nitrogen (kinetic diameter 3.64 a0) and hence oxygen gets adsorbed in carbon molecular sieves and nitrogen is collected as the high-pressure product. The entire operation is fully automatic and controlled by a combination of sequence programmer and quick change over valves. Nitrogen gas of desired purity at 5.5 kg/cm2g pressure and having a dew point of (-) 40 degree celsius is produced by the psa unit, now flows to a surge vessel to balance the fluctuations in pressure and concentration. Now the gas can be stored in a storage tank at 5.5 kg/cm2g pressure from where it can be made available for process application. The storage tank can selected of any desired capacity as per peak hours demand for nitrogen gas or power interruptions. This system is fully automatic and need not any special operator for operation. Once it is started it generates nitrogen at constant flow rate and at constant pressure. Further the produced nitrogen gas can be boosted to high pressures by providing any reliable booster compressors up to desired pressure. We offer various models of nitrogen gas plant and selection is based on the purity required. advantages : - automatic start –up time is only 5- minutes - nitrogen gas supply is always under your control. - self- contained skid mounted units for easy site installation . -very low maintenance costs. -very high reliability to run un-attended plant. -carbon molecular sieves life is minimum 10-12 years in normal working condition and in most cases it lasted the while life time of gas generator. nitrogen capacity: we are manufacturing psa nitrogen gas generators capacity of 1,2,5,10,15, 20 25.40 , 50, 60, 70,80, 100, 125,150, 175 , 200 ,250, 300 ,350 400, 500 ,600 ,800 ,1000 & 1250 & 1500 nm3/hr , purity 95 % to 99.9999% . Pressure up to 10 bar without nitrogen booster compressor . Dew point (-) 40 deg c to (-) 80 deg c. We are also manufacturing psa nitrogen gas generators as per yours specific requirements. we are exporting psa nitrogen gas generators to various countries such as middle east , bangladesh , nepal , brazil, south america, africa , india & other countries. We have our after sales & service teams we are providing after sales & service to all over the world including india nitrogen pressure: standard nitrogen generator produces nitrogen at 5.5 kg /cm 2 g pressure. This pressure comes automatically as feed air pressure to the psa unit is around 7.5kg /cm2g. However , by increasing feed air pressure to 13 kg/cm2g. Nitrogen can be produced even at 10 kg / cm2g. But at high pressure operation , depressurization losses during regeneration are higher, which results in high operation costs. it is most economical to run nitrogen generators at 7.5 kg/ cm2g pressure and produce nitrogen at 5.5 kg/cm2g pressure . However by increasing feed air pressure to 13 kg/cm2g. Nitrogen can be produced even at 10 kg / cm2g. If nitrogen is needed at higher pressure , we can provide a nitrogen booster compressor after the gas generators .by this addition , it is possible to compress nitrogen gas to any desired high pressure. advantages of psa nitrogen gas generators: 1. Self- contained skid mounted units for easy site installation. 2.very low maintenance costs. 3. Very high reliability to run un-attended for months & months. 4. Carbon molecular sieves life is minimum 10-12 years in normal working condition & in most cases it is whole life of the psa nitrogen gas generators. skid mounted psa nitrogen gas generator systems consists of : 1.air compressors system with cooler. 2.air receiver cum moisture separator with automatic drain and high- level alarm. 3.air dryer / refrigerated dryer to make air-sub -saturated 4.coarsed and fine filter for oil and solid removal 5. Ultra fine filters 6.twin tower psa unit 7. Surge vessel 8. N2 gas tanks 9. Booster pump if required for higher discharge pressure of nitrogen gas 10. Microprocessor control panel we offer various models of nitrogen gas plant and selection is based on the purity required which are as follows : ms model : 1. Ms-l 2. Ms-h 1. Ms-l (gas composition ) : nitrogen 98-99 % oxygen 0.1- 2 % hydrogen nil dew point (-)40ºc to (-)80ºc applications : - as inert gas in chemical industries - food & pharmaceutical industries - for fire control in coal mines etc. 1.ms-h ( gas composition ) : nitrogen 99.5 -99.999% oxygen 10 ppm- 500ppm hydrogen nil dew point (-)60ºc to (-)80ºc applications : - as inert gas in chemical - food pharmaceutical industries - heat treatment furnaces - electronic, synthetic fiber, industries. deoxo model applications : manufacturer and exporter of deoxo model. This model is commonly used in metallurgical industries for providing oxygen free nitrogen for heat treatment furnaces. Here, the oxygen is less than 1-ppm and but hydrogen is around 0.5 to 1% which is desirable as reducing constituent in most of heat treatment applications. “ms” models can also be converted into “dx” model by adding palladium deoxo reactor and gas drying unit. “dx” model is also applicable in chemical as well electronic industries. gas composition : nitrogen 99.9999% oxygen 1 to 3ppm(max) hydrogen 0.5% or more dew point (-)40ºc to (-)80ºc applications : - as inert gas in chemical & pharmaceutical industries. - in applications where oxygen impurity is not acceptable. cu deoxo model : cu deoxo model contains an extra nitrogen purification module based on copper deoxo catalyst. This model finds application in synthetic fiber, optical cables & electronic industries. Running cost of this unit is slightly higher because it produces very pure nitrogen gas i.e free from oxygen and hydrogen as well. It is applicable where hydrogen contents are detrimental to the process. gas composition: nitrogen 99.9999% oxygen 1 ppm (max) hydrogen nil dew point (-)40ºc to (-)80ºc applications: - as inert gas in electronic, synthetic fiber, - hitech industries where one needs ultra high purity. industrial uses of nitrogen gas generators : nitrogen generators are extensively used in the following industries: • chemical and petrochemicals industries for inertization, blanketing and purging requirements • ferrous and non-ferrous metallurgical industries for protective atmosphere during annealing, sintering and carburizing processes • pharmaceutical industries for inert atmosphere for reactions and for inert conveying • cement industries for fire prevention and fire fighting in coal mill silos • food packaging and processing industries for extending the shelf life of food products • glass industries for prevention of oxidation during manufacturing • transportation sector for nitrogen tire filling to extend tire life and increased safety please send your enquiry with the following details to us : 1.flow rate of nitrogen gas generator required = nm3. Hr 2.purity of nitrogen gas required = % 3. Discharge pressure of out let of nitrogen gas required = kg/ cm2 4.air compressore type = screw compressure oil cooled type or oil free type 5. Make of air compressore required 6. Any nitrogen gas storge tank required = m3 7. Please confirm us when you are going to finalization the order . we will submit our offer at the earliest to you.
...more
Conveyor Idler
Backed by the team of experts and professionals, we are engaged in offering a wide range of Conveyor Idler. These are manufactured under the strict guidance of our highly skilled professionals to render maximum client satisfaction. Offered Conveyor Idlers are used in various industries for handling of bulk material. We offer these at very affordable prices. Features: Maintenance free High quality Long life Specifications: Diameter: 76-219 mm Length: 190 mm to 3500 mm
Brand Name : Indranil Exports
Material : M.S.
Finishing : Polished
Shape : Round
Color : Black, Red
Condition : New
Application : Conveyor
Length : 5feet, 190 Mm To 3500 Mm
Purity : 100 %
Feature : Durable, Fine Finished, High Quality, Long Life
Load Capacity : As Per Specification
Type : Conveyor Idler
Installation : At Site
After-Sales Service Provided : 12 Moth Period
Country of Origin : India,India
...more
coal handling plants
we are offering dependable solution in coal handling plants. Our coal handling plants are designed to work in all types of industry like power, steel, cements, textiles, chemicals, foods, edible oils, rice plant, sugar, agriculture, chemicals, resins, and many others industry . Our coal handling plants consist of feed hoppers, rack & pinion gates, flap gates, electromagnetic electromechanical vibro feeds , feed belt conveyors, magnetic separators, metal detector , vibrating screens, crusher, recycle bucket elevators recycle belt conveyors, products bucket elevators, product belt conveyors, shuttle conveyors , drag chain conveyors, storage bunkers etc. We designed the coal handling plant as per boiler bunker height & coal requirements for bunker feeding per hour basis . We design the complete belt conveyor system & selection of belt conveyor sizes under the guidance of experienced engineers, these coal handling plants are ensured for their consistent functioning and that too for a longer period of time. All the basic equipment like crushers, screens and feeders etc are manufactured by us in house, resulting in assurance of best performance of complete coal handling plant. We are a reliable manufacturer, exporter and supplier of coal handling plant in india. We are also manufacturing the following conveyors parts as per specification & requirements : 1) Conveyor Roller 2) Carrying Idler 3) Impact Idler 4) Self Align Carrying Idler 5) Garland Idler Set 6) V-Carrying Idler 7) Return Idler 8) Self Align Return Idler 9) Conveyor Structure 10) Drum Pulley 11) Bearing Housing and Labyrinth Seal Attributes : a. Hassle free serviceability b Longer functional life b. Minimum maintenance capacity : 1 tph to 2000 tph. Please send your coal handling plant enquiry to us . We will send our techno-commercial offer with conveyor layout drawing as per your boiler bunker height .We supplied coal handling plant all over the world.
...more
Chemical Pumps
Our storage facility is installed with all necessary amenities essential for the secure storage of the products. Also, we maintain complete hygiene inside the unit. With the help of our brilliant logistics network, we render safe and time-bound deliveries.
Brand Name : Indranil Exports
Condition : New, Good
Type : Pumps
...more
Bulk material handling system.
We are technical capabilities to design, manufacturing , and commissioning the belt conveyors system with bulk densities, moisture, atmospheric condition and corrosive properties for bulk material handling systems for various industries. . we manufacture belt conveyor system with capacities up to 2000tph for various industries. we manufactured the best quality of belt conveyor system for the bulk material handling system for various industry such as cements, lime, sand, soda ash handling system , fertilizers, coal handling system, wood chips handling system, bauxite handling system, wood chips handling system , bagasse handling system , husk handling system .The conveyor handling system are individually designed and engineered for total reliability even under the most demanding service conditions. We have a team of highly skilled engineers and technician for erection and installation of conveyors. An efficient after-sales service for spares and maintenance is an integral part of our commitment to the industry. We had designed, manufactured, installed and commissioned different applications for belt conveyors system , Such vast experience has put us in a very favorable situation to make most appropriate selection of a belt conveyor system for any specific set of conditions for any industry such as sugar, food, distilleries industries , power, coal , chemical , agriculture - chemical industry and others industries. We are also manufacturing the following belt conveyors parts as per specification & requirements : 1) Conveyor Roller 2) Carrying Idler 3) Impact Idler 4) Self Align Carrying Idler 5) Garland Idler Set 6) V-Carrying Idler 7) Return Idler 8) Self Align Return Idler 9) Conveyor Structure 10) Drum Pulley 11) Bearing Housing and Labyrinth Seal Attributes : a.Hassle free serviceability b Longer functional life b.Minimum maintenance
Brand Name : Indranil Exports
...more
ammonia cracker units
We are manufacturing Ammonia cracker unit as per specification & requirements.We can supply all types of Ammonia cracker unit as per specification.
Brand Name : indranil
Type : Ammonia Cracker Units
Condition : New, Good
...more
Chilling Plants
Cooling Tower
Diesel Generator Set
Effluent Treatment Plants
Gearbox
hydrogen purifier
Industrial Boilers
Industrial Pumps
Nitrogen Gas Generator
Pressure Vessel
Storage Tanks
Psa Nitrogen Gas Generators
We are offering nitrogen gas generators, psa nitrogen gas generators. psa nitrogen gas generators : the nitrogen generator produces nitrogen gas from atmospheric air using sieves separation technique. It uses carbon molecular sieves which has ability to preferentially absorb oxygen from air . Our gas generators provides higher efficiency of gas separation . capacity: 1 nm3hr to 1500 nm3hr purity: 95% to 99.9999% pressure: up to 10-bar without nitrogen booster compressor dew point: (-) 40˚c to (-) 80˚c cost of generation: indian rupees: rs. 3- per nm3 us $: 6 cents per nm3 psa principle : nitrogen gas generator consists of two beds filled with carbon molecular sieves . When compressed air is passed , nitrogen comes out as a product gas from one bed while the other bed is simultaneously regenerated by depressurization to atmospheric pressure . This process of gas separation is called “pressure swing adsorption”(psa) psa nitrogen gas generator produces nitrogen gas from atmospheric air by psa (pressure swing adsorption) technology. Psa technique is a simple & reliable process of separation of nitrogen from compressed atmospheric air by adsorption of oxygen over a bed of carbon molecular sieves (cms). Cms is an adsorbent having infinite number of small pores. The diameter of the “bottle necks” is in the same range as those of the molecules. Thus when cms is used in the psa process, an oxygen molecule, having a smaller diameter than a nitrogen molecule traps in to the pores. Therefore the nitrogen is recovered to a high degree while almost all the oxygen is adsorbed. process:- the production of nitrogen gas from atmospheric air is based on pressure swing absorption (psa) principle by adsorption of oxygen gas using a special grade of imported carbon molecular sieves (cms). Atmospheric air is compressed by an air compressor to a pressure of 7.5 kgcm2g and cooled to ambient temperature in a shell and tube type heat exchanger. The condensed moisture shall be drain out automatically from air receiver by automatic drain valve (adt). The compressed air at ambient temperature is passed through psa module packed with activated alumina and special grade of carbon molecular sieves. The production of nitrogen from air by psa technology is largely based on the kinetic separation. Oxygen that is smaller in size (kinetic diameter 3.46 a0) diffuses much faster than nitrogen (kinetic diameter 3.64 a0) and hence oxygen gets adsorbed in carbon molecular sieves and nitrogen is collected as the high-pressure product. The entire operation is fully automatic and controlled by a combination of sequence programmer and quick change over valves. Nitrogen gas of desired purity at 5.5 kgcm2g pressure and having a dew point of (-) 40 degree celsius is produced by the psa unit, now flows to a surge vessel to balance the fluctuations in pressure and concentration. Now the gas can be stored in a storage tank at 5.5 kgcm2g pressure from where it can be made available for process application. The storage tank can selected of any desired capacity as per peak hours demand for nitrogen gas or power interruptions. This system is fully automatic and need not any special operator for operation. Once it is started it generates nitrogen at constant flow rate and at constant pressure. Further the produced nitrogen gas can be boosted to high pressures by providing any reliable booster compressors up to desired pressure. We offer various models of nitrogen gas plant and selection is based on the purity required. advantages : - automatic start –up time is only 5- minutes - nitrogen gas supply is always under your control. - self- contained skid mounted units for easy site installation . -very low maintenance costs. -very high reliability to run un-attended plant. -carbon molecular sieves life is minimum 10-12 years in normal working condition and in most cases it lasted the while life time of gas generator. nitrogen capacity: we are manufacturing psa nitrogen gas generators capacity of 1,2,5,10,15, 20 25.40 , 50, 60, 70,80, 100, 125,150, 175 , 200 ,250, 300 ,350 400, 500 ,600 ,800 ,1000 & 1250 & 1500 nm3hr , purity 95 % to 99.9999% . Pressure up to 10 bar without nitrogen booster compressor . Dew point (-) 40 deg c to (-) 80 deg c. We are also manufacturing psa nitrogen gas generators as per yours specific requirements. we are exporting psa nitrogen gas generators to various countries such as middle east , bangladesh , nepal , brazil, south america, africa , india & other countries. We have our after sales & service teams we are providing after sales & service to all over the world including india nitrogen pressure: standard nitrogen generator produces nitrogen at 5.5 kg cm 2 g pressure. This pressure comes automatically as feed air pressure to the psa unit is around 7.5kg cm2g. However , by increasing feed air pressure to 13 kgcm2g. Nitrogen can be produced even at 10 kg cm2g. But at high pressure operation , depressurization losses during regeneration are higher, which results in high operation costs. it is most economical to run nitrogen generators at 7.5 kg cm2g pressure and produce nitrogen at 5.5 kgcm2g pressure . However by increasing feed air pressure to 13 kgcm2g. Nitrogen can be produced even at 10 kg cm2g. If nitrogen is needed at higher pressure , we can provide a nitrogen booster compressor after the gas generators .by this addition , it is possible to compress nitrogen gas to any desired high pressure. advantages of psa nitrogen gas generators: 1. Self- contained skid mounted units for easy site installation. 2.very low maintenance costs. 3. Very high reliability to run un-attended for months & months. 4. Carbon molecular sieves life is minimum 10-12 years in normal working condition & in most cases it is whole life of the psa nitrogen gas generators. skid mounted psa nitrogen gas generator systems consists of : 1.air compressors system with cooler. 2.air receiver cum moisture separator with automatic drain and high- level alarm. 3.air dryer refrigerated dryer to make air-sub -saturated 4.coarsed and fine filter for oil and solid removal 5. Ultra fine filters 6.twin tower psa unit 7. Surge vessel 8. N2 gas tanks 9. Booster pump if required for higher discharge pressure of nitrogen gas 10. Microprocessor control panel we offer various models of nitrogen gas plant and selection is based on the purity required which are as follows : ms model : 1. Ms-l 2. Ms-h 1. Ms-l (gas composition ) : nitrogen 98-99 % oxygen 0.1- 2 % hydrogen nil dew point (-)40ºc to (-)80ºc applications : - as inert gas in chemical industries - food & pharmaceutical industries - for fire control in coal mines etc. 1.ms-h ( gas composition ) : nitrogen 99.5 -99.999% oxygen 10 ppm- 500ppm hydrogen nil dew point (-)60ºc to (-)80ºc applications : - as inert gas in chemical - food pharmaceutical industries - heat treatment furnaces - electronic, synthetic fiber, industries. deoxo model applications manufacturer and exporter of deoxo model. This model is commonly used in metallurgical industries for providing oxygen free nitrogen for heat treatment furnaces. Here, the oxygen is less than 1-ppm and but hydrogen is around 0.5 to 1% which is desirable as reducing constituent in most of heat treatment applications. “ms” models can also be converted into “dx” model by adding palladium deoxo reactor and gas drying unit. “dx” model is also applicable in chemical as well electronic industries. gas composition : nitrogen 99.9999% oxygen 1 to 3ppm(max) hydrogen 0.5% or more dew point (-)40ºc to (-)80ºc applications : - as inert gas in chemical & pharmaceutical industries. - in applications where oxygen impurity is not acceptable. cu deoxo model cu deoxo model contains an extra nitrogen purification module based on copper deoxo catalyst. This model finds application in synthetic fiber, optical cables & electronic industries. Running cost of this unit is slightly higher because it produces very pure nitrogen gas i.e free from oxygen and hydrogen as well. It is applicable where hydrogen contents are detrimental to the process. gas composition: nitrogen 99.9999% oxygen 1 ppm (max) hydrogen nil dew point (-)40ºc to (-)80ºc applications: - as inert gas in electronic, synthetic fiber, - hitech industries where one needs ultra high purity. industrial uses of nitrogen gas generators : nitrogen generators are extensively used in the following industries: • chemical and petrochemicals industries for inertization, blanketing and purging requirements • ferrous and non-ferrous metallurgical industries for protective atmosphere during annealing, sintering and carburizing processes • pharmaceutical industries for inert atmosphere for reactions and for inert conveying • cement industries for fire prevention and fire fighting in coal mill silos • food packaging and processing industries for extending the shelf life of food products • glass industries for prevention of oxidation during manufacturing • transportation sector for nitrogen tire filling to extend tire life and increased safety please send your enquiry with the following details to us : 1.flow rate of nitrogen gas generator required = nm3. Hr 2.purity of nitrogen gas required = % 3. Discharge pressure of out let of nitrogen gas required = kg cm2 4.air compressore type = screw compressure oil cooled type or oil free type 5. Make of air compressore required 6. Any nitrogen gas storge tank required = m3 7. Please confirm us when you are going to finalization the order . we will submit our offer at the earliest to you. psa nitrogen gas generators : the nitrogen generator produces nitrogen gas from atmospheric air using sieves separation technique. It uses carbon molecular sieves which has ability to preferentially absorb oxygen from air . Our gas generators provides higher efficiency of gas separation . capacity: 1 nm3hr to 1500 nm3hr purity: 95% to 99.9999% pressure: up to 10-bar without nitrogen booster compressor dew point: (-) 40˚c to (-) 80˚c cost of generation: indian rupees: rs. 3- per nm3 us $: 6 cents per nm3 psa principle : nitrogen gas generator consists of two beds filled with carbon molecular sieves . When compressed air is passed , nitrogen comes out as a product gas from one bed while the other bed is simultaneously regenerated by depressurization to atmospheric pressure . This process of gas separation is called “pressure swing adsorption”(psa) psa nitrogen gas generator produces nitrogen gas from atmospheric air by psa (pressure swing adsorption) technology. Psa technique is a simple & reliable process of separation of nitrogen from compressed atmospheric air by adsorption of oxygen over a bed of carbon molecular sieves (cms). Cms is an adsorbent having infinite number of small pores. The diameter of the “bottle necks” is in the same range as those of the molecules. Thus when cms is used in the psa process, an oxygen molecule, having a smaller diameter than a nitrogen molecule traps in to the pores. Therefore the nitrogen is recovered to a high degree while almost all the oxygen is adsorbed. process:- the production of nitrogen gas from atmospheric air is based on pressure swing absorption (psa) principle by adsorption of oxygen gas using a special grade of imported carbon molecular sieves (cms). Atmospheric air is compressed by an air compressor to a pressure of 7.5 kgcm2g and cooled to ambient temperature in a shell and tube type heat exchanger. The condensed moisture shall be drain out automatically from air receiver by automatic drain valve (adt). The compressed air at ambient temperature is passed through psa module packed with activated alumina and special grade of carbon molecular sieves. The production of nitrogen from air by psa technology is largely based on the kinetic separation. Oxygen that is smaller in size (kinetic diameter 3.46 a0) diffuses much faster than nitrogen (kinetic diameter 3.64 a0) and hence oxygen gets adsorbed in carbon molecular sieves and nitrogen is collected as the high-pressure product. The entire operation is fully automatic and controlled by a combination of sequence programmer and quick change over valves. Nitrogen gas of desired purity at 5.5 kgcm2g pressure and having a dew point of (-) 40 degree celsius is produced by the psa unit, now flows to a surge vessel to balance the fluctuations in pressure and concentration. Now the gas can be stored in a storage tank at 5.5 kgcm2g pressure from where it can be made available for process application. The storage tank can selected of any desired capacity as per peak hours demand for nitrogen gas or power interruptions. This system is fully automatic and need not any special operator for operation. Once it is started it generates nitrogen at constant flow rate and at constant pressure. Further the produced nitrogen gas can be boosted to high pressures by providing any reliable booster compressors up to desired pressure. We offer various models of nitrogen gas plant and selection is based on the purity required. advantages : - automatic start –up time is only 5- minutes - nitrogen gas supply is always under your control. - self- contained skid mounted units for easy site installation . -very low maintenance costs. -very high reliability to run un-attended plant. -carbon molecular sieves life is minimum 10-12 years in normal working condition and in most cases it lasted the while life time of gas generator. nitrogen capacity: we are manufacturing psa nitrogen gas generators capacity of 1,2,5,10,15, 20 25.40 , 50, 60, 70,80, 100, 125,150, 175 , 200 ,250, 300 ,350 400, 500 ,600 ,800 ,1000 & 1250 & 1500 nm3hr , purity 95 % to 99.9999% . Pressure up to 10 bar without nitrogen booster compressor . Dew point (-) 40 deg c to (-) 80 deg c. We are also manufacturing psa nitrogen gas generators as per yours specific requirements. we are exporting psa nitrogen gas generators to various countries such as middle east , bangladesh , nepal , brazil, south america, africa , india & other countries. We have our after sales & service teams we are providing after sales & service to all over the world including india nitrogen pressure: standard nitrogen generator produces nitrogen at 5.5 kg cm 2 g pressure. This pressure comes automatically as feed air pressure to the psa unit is around 7.5kg cm2g. However , by increasing feed air pressure to 13 kgcm2g. Nitrogen can be produced even at 10 kg cm2g. But at high pressure operation , depressurization losses during regeneration are higher, which results in high operation costs. it is most economical to run nitrogen generators at 7.5 kg cm2g pressure and produce nitrogen at 5.5 kgcm2g pressure . However by increasing feed air pressure to 13 kgcm2g. Nitrogen can be produced even at 10 kg cm2g. If nitrogen is needed at higher pressure , we can provide a nitrogen booster compressor after the gas generators .by this addition , it is possible to compress nitrogen gas to any desired high pressure. advantages of psa nitrogen gas generators: 1. Self- contained skid mounted units for easy site installation. 2.very low maintenance costs. 3. Very high reliability to run un-attended for months & months. 4. Carbon molecular sieves life is minimum 10-12 years in normal working condition & in most cases it is whole life of the psa nitrogen gas generators. skid mounted psa nitrogen gas generator systems consists of : 1.air compressors system with cooler. 2.air receiver cum moisture separator with automatic drain and high- level alarm. 3.air dryer refrigerated dryer to make air-sub -saturated 4.coarsed and fine filter for oil and solid removal 5. Ultra fine filters 6.twin tower psa unit 7. Surge vessel 8. N2 gas tanks 9. Booster pump if required for higher discharge pressure of nitrogen gas 10. Microprocessor control panel we offer various models of nitrogen gas plant and selection is based on the purity required which are as follows : ms model : 1. Ms-l 2. Ms-h 1. Ms-l (gas composition ) : nitrogen 98-99 % oxygen 0.1- 2 % hydrogen nil dew point (-)40ºc to (-)80ºc applications : - as inert gas in chemical industries - food & pharmaceutical industries - for fire control in coal mines etc. 1.ms-h ( gas composition ) : nitrogen 99.5 -99.999% oxygen 10 ppm- 500ppm hydrogen nil dew point (-)60ºc to (-)80ºc applications : - as inert gas in chemical - food pharmaceutical industries - heat treatment furnaces - electronic, synthetic fiber, industries. deoxo model applications : manufacturer and exporter of deoxo model. This model is commonly used in metallurgical industries for providing oxygen free nitrogen for heat treatment furnaces. Here, the oxygen is less than 1-ppm and but hydrogen is around 0.5 to 1% which is desirable as reducing constituent in most of heat treatment applications. “ms” models can also be converted into “dx” model by adding palladium deoxo reactor and gas drying unit. “dx” model is also applicable in chemical as well electronic industries. gas composition : nitrogen 99.9999% oxygen 1 to 3ppm(max) hydrogen 0.5% or more dew point (-)40ºc to (-)80ºc applications : - as inert gas in chemical & pharmaceutical industries. - in applications where oxygen impurity is not acceptable. cu deoxo model : cu deoxo model contains an extra nitrogen purification module based on copper deoxo catalyst. This model finds application in synthetic fiber, optical cables & electronic industries. Running cost of this unit is slightly higher because it produces very pure nitrogen gas i.e free from oxygen and hydrogen as well. It is applicable where hydrogen contents are detrimental to the process. gas composition: nitrogen 99.9999% oxygen 1 ppm (max) hydrogen nil dew point (-)40ºc to (-)80ºc applications: - as inert gas in electronic, synthetic fiber, - hitech industries where one needs ultra high purity. industrial uses of nitrogen gas generators : nitrogen generators are extensively used in the following industries: • chemical and petrochemicals industries for inertization, blanketing and purging requirements • ferrous and non-ferrous metallurgical industries for protective atmosphere during annealing, sintering and carburizing processes • pharmaceutical industries for inert atmosphere for reactions and for inert conveying • cement industries for fire prevention and fire fighting in coal mill silos • food packaging and processing industries for extending the shelf life of food products • glass industries for prevention of oxidation during manufacturing • transportation sector for nitrogen tire filling to extend tire life and increased safety please send your enquiry with the following details to us : 1.flow rate of nitrogen gas generator required = nm3. Hr 2.purity of nitrogen gas required = % 3. Discharge pressure of out let of nitrogen gas required = kg cm2 4.air compressore type = screw compressure oil cooled type or oil free type 5. Make of air compressore required 6. Any nitrogen gas storge tank required = m3 7. Please confirm us when you are going to finalization the order . we will submit our offer at the earliest to you.
...more
Consultancy Services , Marketing Services, Liaison Services
We are providing various consultancy services for our customer . We are providing consultancy services for vendor registration with E.I. L , Power Grid Corporation, NTPC , BHEL , Power sector private companies, PDIL , ONGC, Indian Oils , Bharat Petroleum, Ministry of Power , Ministry of Railways, Ministry of Civil Aviation , Ministry of coal & other Government Ministry as per requirements. We are also doing follow-up services for various Tenders & submission of tenders of various customers , We are providing various engineering services for the following sector : 1. Vendor registration with M/s Holtech Consulting Pvt. Ltd,Gurgaon ( Reputed Cement Consultant in India ) & M/s Ercom Engineers Pvt. Ltd ( Cement Consultants) New Delhi. Follow up with them for various types of tenders & cements project of various cements plants 2. Vendor registration & follow for various project with M/s PDIL , Noida for fertilizer industry behalf of various vendors & equipments suppliers . 3. Vendor registration with Steel Plants consultants & Sponge Consultants in India & follow up with various Steel Plant & sponge Iron companies in India regarding supply of various equipments for the steel plants & sponge iron companies behalf of various equipments supplier . 4. Vendor registration with various paper plants Consultants & paper Plants large & medium paper plants in India & abroad & follow up with the various paper plants consultants & Paper Plants in India & abroad regarding supply of various paper plants & machineries behalf of various equipments supplier . 5. Vendor registration with the various engineering consultants , architect & end customers regarding various Effluents Treatments & water treatment projects in India & Abroad & follow �up with them for various Effluent Treatment & water Treatment project supply behalf of various projects suppliers in India . 6. Vendor registration & follow up with M/s NTPC engineering services , Noida behalf of various equipments suppliers for their various power project. 7. Vendor registration & follow up for tender submission for EIL , ONGC , Indian oil , Bharat petroleum & others oil sector companies behalf of various companies . 8. Vendor registration with various private sector power company in Delhi , Noda , Gurgaon & follow up for various projects behalf of various equipments & project suppliers. 9. Vendor registration with various pharmaceutical industry in north India & Gujarat & follow up for various supply of equipments behalf of equipment suppliers. 10. Follow �up & vendor registration for various ash Handling projects, Bulk Material Handling projects, Large & medium Fire �Fighting projects, Piping projects, Industrial pumps for various projects, Cement plants equipment supply, Steel & iron Plant Supply, Pharmaceutical equipments supply, various power equipments supply, Transmission & distribution projects with NTPC, BHEL, Power Grid corporation, State electricity boards etc behalf of various suppliers in India. We are providing all types of consultancy services , Liaison services , Marketing services for various industry including exports services to various manufacturers . We are doing retainer services for various industry. Please write to us. We will solved all your problem . We are interested to do business with you on long time basic. We are also providing small office services for various manufacturers in India . Please write to us . We will help you in all possible ways . Looking for early reply in these regards at the earliest . Thanking you Your Faith fully R.N.Bhattacharya Director For Indranil Exports Corporation 371- D , Pocket-2 , Phase-1 Mayur Vihar , Delhi -110091 Phone: +91-11-22793027 Mobile :=91-9311425319 E-mail : indranilexports@yahoo.co.in E-mail : indranilexports@gmail.com
...more
Marketing services , Consultancy & Liaison services
We are providing various consultancy services for our customer . We are providing consultancy services for vendor registration with E.I. L , Power Grid Corporation, NTPC , BHEL , Power sector private companies, PDIL , ONGC, Indian Oils , Bharat Petroleum, Ministry of Power , Ministry of Railways, Ministry of Civil Aviation , Ministry of coal & other Government Ministry as per requirements. We are also doing follow-up services for various Tenders & submission of tenders of various customers , We are providing various engineering services for the following sector : 1. Vendor registration with M/s Holtech Consulting Pvt. Ltd,Gurgaon ( Reputed Cement Consultant in India ) & M/s Ercom Engineers Pvt. Ltd ( Cement Consultants) New Delhi. Follow up with them for various types of tenders & cements project of various cements plants 2. Vendor registration & follow for various project with M/s PDIL , Noida for fertilizer industry behalf of various vendors & equipments suppliers . 3. Vendor registration with Steel Plants consultants & Sponge Consultants in India & follow up with various Steel Plant & sponge Iron companies in India regarding supply of various equipments for the steel plants & sponge iron companies behalf of various equipments supplier . 4. Vendor registration with various paper plants Consultants & paper Plants large & medium paper plants in India & abroad & follow up with the various paper plants consultants & Paper Plants in India & abroad regarding supply of various paper plants & machineries behalf of various equipments supplier . 5. Vendor registration with the various engineering consultants , architect & end customers regarding various Effluents Treatments & water treatment projects in India & Abroad & follow �up with them for various Effluent Treatment & water Treatment project supply behalf of various projects suppliers in India . 6. Vendor registration & follow up with M/s NTPC engineering services , Noida behalf of various equipments suppliers for their various power project. 7. Vendor registration & follow up for tender submission for EIL , ONGC , Indian oil , Bharat petroleum & others oil sector companies behalf of various companies . 8. Vendor registration with various private sector power company in Delhi , Noda , Gurgaon & follow up for various projects behalf of various equipments & project suppliers.. 9. Vendor registration with various pharmaceutical industry in north India & Gujarat & follow up for various supply of equipments behalf of equipment suppliers. 10. Follow �up & vendor registration for various ash Handling projects, Bulk Material Handling projects, Large & medium Fire �Fighting projects, Piping projects, Industrial pumps for various projects, Cement plants equipment supply, Steel & iron Plant Supply, Pharmaceutical equipments supply, various power equipments supply, Transmission & distribution projects with NTPC, BHEL, Power Grid corporation, State electricity boards etc behalf of various suppliers in India. We are providing all types of consultancy services , Liaison services , Marketing services for various industry including exports services to various manufacturers . We are doing retainer services for various industry. Please write to us. We will solved all your problem . We are interested to do business with you on long time basic. We are also providing small office services for various manufacturers in India . Please write to us . We will help you in all possible ways . Looking for early reply in these regards at the earliest .
...more
engineering consulting service
We are providing various engineering consultancy services.
...more
Engineering Services
gas refining services
oil refining services
Sourcing Agents
Tender Services
turnkey projects services
Liaison Services
We are providing various consultancy services for our customer . We are providing consultancy services for vendor registration with E.I. L , Power Grid Corporation, NTPC , BHEL , Power sector private companies, PDIL , ONGC, Indian Oils , Bharat Petroleum, Ministry of Power , Ministry of Railways, Ministry of Civil Aviation , Ministry of coal & other Government Ministry as per requirements. We are also doing follow-up services for various Tenders & submission of tenders of various customers , We are providing various engineering services for the following sector : 1. Vendor registration with Ms Holtech Consulting Pvt. Ltd,Gurgaon ( Reputed Cement Consultant in India ) & Ms Ercom Engineers Pvt. Ltd ( Cement Consultants) New Delhi. Follow up with them for various types of tenders & cements project of various cements plants 2. Vendor registration & follow for various project with Ms PDIL , Noida for fertilizer industry behalf of various vendors & equipments suppliers . 3. Vendor registration with Steel Plants consultants & Sponge Consultants in India & follow up with various Steel Plant & sponge Iron companies in India regarding supply of various equipments for the steel plants & sponge iron companies behalf of various equipments supplier . 4. Vendor registration with various paper plants Consultants & paper Plants large & medium paper plants in India & abroad & follow up with the various paper plants consultants & Paper Plants in India & abroad regarding supply of various paper plants & machineries behalf of various equipments supplier . 5. Vendor registration with the various engineering consultants , architect & end customers regarding various Effluents Treatments & water treatment projects in India & Abroad & follow �up with them for various Effluent Treatment & water Treatment project supply behalf of various projects suppliers in India . 6. Vendor registration & follow up with Ms NTPC engineering services , Noida behalf of various equipments suppliers for their various power project. 7. Vendor registration & follow up for tender submission for EIL , ONGC , Indian oil , Bharat petroleum & others oil sector companies behalf of various companies . 8. Vendor registration with various private sector power company in Delhi , Noda , Gurgaon & follow up for various projects behalf of various equipments & project suppliers.. 9. Vendor registration with various pharmaceutical industry in north India & Gujarat & follow up for various supply of equipments behalf of equipment suppliers. 10. Follow �up & vendor registration for various ash Handling projects, Bulk Material Handling projects, Large & medium Fire �Fighting projects, Piping projects, Industrial pumps for various projects, Cement plants equipment supply, Steel & iron Plant Supply, Pharmaceutical equipments supply, various power equipments supply, Transmission & distribution projects with NTPC, BHEL, Power Grid corporation, State electricity boards etc behalf of various suppliers in India. We are providing all types of consultancy services , Liaison services , Marketing services for various industry including exports services to various manufacturers . We are doing retainer services for various industry. Please write to us. We will solved all your problem . We are interested to do business with you on long time basic. We are also providing small office services for various manufacturers in India . Please write to us . We will help you in all possible ways . Looking for early reply in these regards at the earliest .
...more
Reviews & Ratings
Write a ReviewBe first to Rate
Rate ThisOpening Hours
Share your Correspondence Details to receive messages from Indranil Exports Corporation
Post Free Ad