Industrial Valve Dealers in Nehru Place, Delhi

The t type strainers offered by us are ideal to remove physical impurities from liquids, steam, gases, etc. Available with screw and flanged construction, the t type strainers are used for inline applications. Further, these t type strainers are offered in forged, cast and fabricated construction.

We are offering manifold valves. it consists of the followinf categories: 1.valve manifold 2.valve manifold accessories (in picture: wall supports for valve manifold).

• Feature: Heavy duty design,Corrosion resistance,Glossy finish,Exceptionally durable

The poppet damper are used for quick operation and tight shut off application, Construction – The body of poppet damper is fabricated from different type of material suitable for site condition and client requirement.Body: A36, IS 2062, A516, IS 2002, Corten, SS 304,SS 316, Inconel etc, 3. Shaft: En8, SS 410, SS 304,SS 316, Inconel etc, 5. Bearing: C.I lined Bush type with Grafoil Sheet, maintenance free Antifriction.

The gate valve, also known as a sluice valve, is a valve that opens by lifting a round or rectangular gate/wedge out of the path of the fluid. The distinct feature of a gate valve is the sealing surfaces between the gate and seats are planar, so gate valves are often used when a straight-line flow of fluid and minimum restric­tion is desired. The gate faces can form a wedge shape or they can be parallel. Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the petroleum industry. On opening the gate valve, the flow path is enlarged in a highly nonlinear manner with respect to percent of opening. This means that flow rate does not change evenly with stem travel. Also, a partially open gate disk tends to vibrate from the fluid flow. Most of the flow change occurs near shutoff with a relatively high fluid velocity causing disk and seat wear and eventual leakage if used to regulate flow. Typical gate valves are designed to be fully opened or closed. When fully open, the typical gate valve has no obstruction in the flow path, resulting in very low friction loss. Gate valves are characterised as having either a rising or a nonrising stem. Rising stems provide a visual indication of valve position because the stem is attached to the gate such that the gate and stem rise and lower together as the valve is operated. Nonrising stem valves may have a pointer threaded onto the upper end of the stem to indicate valve position, since the gate travels up or down the stem on the threads without raising or lowering the stem. Nonrising stems are used underground or where vertical space is limited. Bonnets provide leakproof closure for the valve body. Gate valves may have a screw-in, union, or bolted bonnet. Screw-in bonnet is the simplest, offering a durable, pressure-tight seal. Union bonnet is suitable for applications requiring frequent inspection and cleaning. It also gives the body added strength. Bolted bonnet is used for larger valves and higher pressure applications. Another type of bonnet construction in a gate valve is pressure seal bonnet. This construction is adopted for valves for high pressure service, typically in excess of 15 MPa (2250 psi). The unique feature about the pressure seal bonnet is that the body - bonnet joints seals improves as the internal pressure in the valve increases, compared to other constructions where the increase in internal pressure tends to create leaks in the body-bonnet joint.Gate valves may have flanged ends which are drilled according to pipeline compatible flange dimensional standards. Gate valves are typically constructed from cast iron, ductile iron, cast carbon steel, gun metal, stainless steel, alloy steels, and forged steels.  

• specification: Six-port, three way design for duplexing filters,Unique floating pad design for port sealing,Carbon steel and stainless steel construction,Split valves available for duplexing coolers,Sizes from 1-½ inches to 8 inches,Pressures from 150 PSI to 5000 PSI,Z

• Material: Metal
• Number Of Way: 2way, 3way
• Application: Gas Fitting, Oil Fitting, Water Fitting
• Pressure: High, Low, Medium
• Feature: Casting Approved, Durable
• Moq: As per Customer
• Pressure Range: 0.5 to 10 bar

Cylinder Valves, LPG Cylinders

• Pipe Size: 1.5″

Multiport valve are available in 1 inch 3-position. Multiport valves are constructed of molded ABS material with heavy-duty plastic handles and are 100% factory tested.

The over pressure shut off valve is gas safety cut-off device is an apparatus which blocks the flow of gas if the controlled pressure reaches the set-point for its intervention, or if actuated manually. The valve is suitable for medium and high pressure gas flow. The over pressure cut-off device is always supplied complete with nipple for the sensing line. Before installing the valve you must ensure that the valve can be inserted in the space provided and that there is enough room for later maintenance operations.

Features   » Pentaflo's butterfly valves are able to open and close under equalized water pressure on the disc sides as well as to close at full Turbine discharge. » In addition, emergency closure valves shall close automatically in case of penstock rupture. The opening is done by means of one standard servomotor. » We manufacture turbine inlet butterfly valve double off set type (double eccentric). » We offer hydraulic operator with the provision of counter weight for self-closing in the event of any fault. » The valves are fabricated or made from cast steel. » Size ranges from ø 150mm to 2500mm.

AIPL Super Efficient Automatic Drain Valve For Condensate Removal. In Compressed Air Systems, Moisture is an Unavoidable Critical Element which is absorbed from the atmospheric air. The acumulation of moisture will be very very large. The compressed air along with water causes costly- Damage within few minutes to Pneumatic Equipments Tools To reduce the maintenance cost in the Pneumatic controls systems "AIPL" has developed and "AIPL AUTOMATIC DRAIN VALVE" based on solid state Electronic Adjustable Timer.

• Material: Cast iron
• Valve Size: 15 mm to 100 mm
• Media: Fuel
• Pressure: Upto 150 kg/cm2
• Temperature of Media: High Temperature
• Packing Type: Box
• Power: Manual

• Material: Cast Iron
• Packing Type: Box

• Size: 1/2 INCH - 4 INCH
• Country of Origin: Made in India
• Material: Aluminium Casting
• Ends: Threaded
• Max Pressure: 10kg/cm2

Manifold Valves Fittings, Pressure Gauges, differential pressure switches

The basic use of the rotary airlock feeder is as an airlock transition point, sealing pressurized systems against loss of air or gas while maintaining a flow of material between components with different pressure.

Pump Sets, Horizontal Centrifugal Pump

This indigenisation is a reverse engineering project We manufacture High Pressure Valves of Air Primer. Valve consists of a body and shut off mechanism inside the body. Body has through axial holes of different diameters over the length. Lower part the hole is 8 mm in dia, the remaining part is of 22 mmin dia. (MOC – SS). The upper part of the body is provided with female thread for securing stem assembly and male thread for fastening the valveon the bottle. From one side and under the body there is a connection with male threads for attaching to the pipe lines. The shut off mechanism consist of valve assembly with a pad made of polyamide resin, stem assembly (MOC - MS), bushing (MOC – Gun Metal), gasket (MOC - Copper), spring (MOC – Case hardened steel) with packing . The stem assembly in its turn has a nut, stem, ball and pivot journal. Hand wheel assembly is fixed by nut on the square end of stem for opening and closing of the valve. The air leakage from the valve is prevented by a seal and made in movable and fixed joint. The movable joint of valve end and bushing are sealed by rubber rings. Valve assemblies have tested for the leak tightness by compressed air at a pressure of 400 kgf/cm² and hydraulic test for strength at a hydraulic pressure of 600 kgf/cm²      

Butterfly Valve Standard Series, Pvc Butterfly Valves, Check Valves

Check Valves, reverse osmosis tank, Horizontal Pressure Tank

Selling Agent

Gas Leak Check Valve, Sliding Vane Pump, lpg vaporizers

Industrial Valve, Engineering Products, Steam Trap, Strainers

Aerosol Valves, aerosol pumps

Industrial Valve, Water Pumps, pumping equipment

regulators, Cylinders

pneumatic safety valves