Marshall Stability Apparatus Dealers in Anand Parbat, Delhi

Marshall Stability Test Apparatus is a very important bitumen testing equipments genrally highly demanded by construction industry. The apparatus is suitable for conducting Marshall stability test of bituminous mixture. The apparatus can truly judge the fail point of bituminous mixtures to design the match ratio or check the construction quality of bitumen road surface.

• Material: Steel
• Voltage: 220V
• Power: 0.25 To 5 kw
• Brand Name: Steco
• Automation: Semi-Automatic
• Capacity: 50 KN
• Phase: Single Phase
• Ring Capacity: 30 KN
• Usage: Marshall Stability Testing

We are connected with well-known transport providers to make sure the distribution of deliveries is done out without a problem and on time. We own a substantial warehouse to keep the stacked products safely until final dispatch. With the leading technologies and automated systems, we ensure that the fragile products are sternly packed and piled up systematically.   Product Code : EKE 550-1It consists of : EKE 552-1 Marshall Load Frame cap 25 KN, single speed, 50.8mm / min. 1 No. EKE 55001 Breaking Head Stability Mould, with a dial gauge EKE 072 (having 25 mm travel and 0.01 mm least count), for flow measurement 1 No. EKE 55002 Compaction Mould, Steel, cylindrical 3 Nos. EKE 55003 Base Plate 3 Nos. EKE 55004 Extension Collar 3 Nos. EKE 55005 Compaction Pedestal, Manual Operation, comprising a Steel Plate capped on a wooden post. A Mould Clamp is fitted to the top of the plate 1 No. EKE 55006 Compaction Hammer, for use with Compaction Pedestal and Mould, weight 4.5 kg with a free fall of 457 mm 2 Nos. EKE 55007 Load Transfer Bar 1 No. Essential Accessory EKE 271 Proving Ring, capacity 25 kN (2,500 kgf) EKE 55020 : Electronic Conversion Kit for Marshall Apparatus EKE 550 Marshall Apparatus with two speeds - 50.8 and 61 mm per minute is also available on request.

KEWIL Ring and Ball Apparatus Ring and ball apparatus is meant for determining soft point of bitumen. Using various scientific principles it is also used in petroleum industry, construction projects, paint industry etc.

Marshall Apparatus Consists Of: Robust construction 50KN capacity Rate of travel 50.8mm/min Safety cut-off switch It consists of body housing, a geared screw jack and motor drive mechanism suitable for operation on 230 V, 50Hz, Single Phase, A.C. supply. A. MARSHALL LOAD FRAME 1 No. B. Breaking Head Stability Mould, with a dial gauge ( having 25mm travel and 0.01mm least count), for flow measurement 1 No.C. Compaction Mould, Steel cylindrical 3 Nos.D. Base Plate 3 Nos.E. Extension Collar 3 Nos.F. Compaction Pedestal, Manual Operation, Comprising a steel plate capped on a wooden post. A Mould Clamp is fitted to the top of the plate . 1 No.G. Compaction Hammer, satisfies BS 598. The hammer has a 4535 g sliding weight with a free fall of 457 mm 2 Nos.H. Load Transfer Bar 1 No. I. Paper Discs, Non absorbent, 11 cm diameter pack of 100 No. 1 Pkt.

The firm is known for building efficient apparatus for carrying out the Marshall Stability Test. The Marshall Stability Test Apparatus is applicable to hot mix designs by availing bitumen and aggregates. In this procedure, the resistance to plastic deformation of cylindrical specimen of bituminous mixture is calculated when the same is loaded at periphery at 5 cm per min. The two prime features of the Marshall method of designing mixes are Density : Voids AnalysisStability : Flow Tests This test method is used in the design and evaluation of bituminous paving mixes. The test method is widely used in routine test programmers for paving works. Specifications A loading unit motorized, capacity 5000kgf with two telescopic pillars and an adjustable cross head. The Limit switches are attached inside to regulate the upward or downward movement of the pillars. On off reversing switch and indicator lamps are on the front side while a hand wheel to manually displace the pillars is on the right side. The load frame has fixed speed of 5.80cm per minute, which is operated on 230 volts AC3 Specimen mold 10.16cm I.D. x 7.6cm high with base plate and extension collarOne Kit for specimen extraction that consists of one each load transfer bar, steel ball and specimen extracting plateOne number compaction pedal with specimen mold holder1 Breaking head assembly with provision to fix flow meterThe Marshal Stability of mix can be defined as a maximum load carried by a compacted specimen at a standard test temperature of 60oC