srd Chawri Bazar, Delhi

• Waterproof and resistant to UV rays • Dimensional stability • Puncturing resistant • RAL colors available upon request for architectural designs and proposals.  Full adherence to horizontal surfaces:   APPLICATION- Adhered to insulation boards - Adhered to concrete supports - Adhered to existing coverings STORAGE Roll: 1,60m x 20m x 1,2mmPallet: 16 Rolls / 512m² Roll: 1,60m x 20m x 1,5mmPallet: 16 Rolls / 512m² Roll: 1,60m x 20m x 1,8mmPallet: 12 Rolls / 384m² Roll 1,60m x 20m x 2,0mmPallet: 12 Rolls / 384m²

Extruded polystyrene XPS is the ideal product for the insulation of roofs. In the case of inverted flat roofs the recommended product is XPS SL which is placed on top of the waterproof layer. Apart from being and energy efficient application, the XPS helps to protect the waterproofing membrane from damage and UV degradation. XPS SL has got closed cell structure with a lap joint rebate to facilitate its placement on the roof.  Application   XPS SL is applied on: • Inverted roofs, pitched roofs, and for restoration of these roofs • Perimeter insulation for walls • Load-bearing foundation slabs • Forged steel, slabs and pavement • Roads and railway lines

TECSOUND® is a high density polymer-based, asphalt-free, synthetic soundproofing membrane, that offers good acoustic insulation in different building elements. It is equipped with a tissue non-tissue polypropylene fleece on its upper side to improve the tear strength of the membrane and at the same time offer a protection or a finishing. High acoustic insulation, combined with soft, flexible elements. • High sound damping capacity on metal surfaces. • Flexible. • Easy to handle and adaptable to uneven surfaces. • Easy to cut with a knife or scissors • Good bonding to most of the types of surfaces. • Acts as a vapour control layer • Cold- and heat-resistance. • Excellent ageing resistance. • Rotproof. APPLICATION  Soundproofing against airborne noise in ceilings and lightweight roofs. • Reduction of impact noise level in all types of floors, sandwiched between floor slabs and loose-laid flooring. • Damping of impact noise caused by atmospheric agents on metal decks. • Soundproofing of air conditioning ducts and pipes. • Combined with sound-absorbent materials, it offers products with high acoustic performance. • Its applications in the industrial field cover from the soundproofing of booths to the acoustic insulation of machine-rooms, gutter pipes, sound-damping of metal sheets, etc. INSTALLATION Substrate: TECSOUND lends itself to all types of normal building substrates (renderings, gypsum board, metal, DM, plastic materials). The substrate must be even, smooth, clean and dry. It must also be free from elements that could damage the membrane. If the rendering is old, its condition must be checked to avoid adherence problems of the TECSOUND sheet to the rendering. Installation of the membrane: prior to installing the membrane, an adhesive must be applied to both substrate and membrane, and left to dry according to the instructions of the adhesive manufacturer before bonding the two surfaces. Pressure must be exerted on all the points to ensure correct adherence. It could be installed mechanically fastened. The number of fixings will depend on the product, the support and the system where the membrane will be applied. Installation of the membrane on metal decks: Extend the roll over the substrate progressively, trying to keep the fleece remained on the upper side so it protects the membrane. The membrane must be applied in such a way that the length of the roll is perpendicular to the direction of the deck profile. The membrane must be made to follow the profile of the metal support at all times, ensuring that there is no formation of air pockets. The thermal insulation boards are then installed, mechanically fastened. Laps: Overlap 5 cm both vertically and horizontally. Care must be taken to always seal the laps correctly, as small openings can reduce the level of acoustic insulation required. Yield: 1 m2 of membrane covers approximately 0.90 m2 of surface area, including overlaps.] Storage   Tecsound® 35 Roll:8 m. x 1,22 m Pallet:24 rolls (234,24 m²) Tecsound® 50 Roll:6 m. x 1,22 m Pallet:24 rolls (175,68 m²) Tecsound® 70 Roll:5 m. x 1,22 m Pallet:24 rolls (146,4 m²) Tecsound® 100 Roll:4 m. x 1,20 m Pallet:1 m. x 1,20 m. sheet (*) 21 rolls (100,8 m²) 75 sheets (90 m²)   Regulations · In accordance with the following norms: CTE-DB-HR, EN ISO 140-1, EN ISO 140-3, EN ISO 140-6, EN ISO 140-8, EN 20140-2 and EN ISO 717/1/2. · Quality System in accordance with ISO:9001

ROOFTEX 120 Is a non-woven geotextile, 100% PET fibres, needlepunctured with subsequent heat treatment and calendared; used as a separating, filtering, drainage and protective layer in building... Advantages • Biological resistence: It is not affected by bacterias or fungus. No nutrients contents, so it is not attacked by rodents or termites Application • Reinforcement : provides resistance to the puncturing of the waterproofing membrane. • Filtration and drainage : good permeability to water, allows the passage of water, maintaining the fine soil particles. • Separation : prevents mixing of particles from different soils. Prevents contact between non-compatible materials. Acts of permeable barrier between materials with different structures.   Storage   Roll: 2.2 m x 150 m Amount per horizontal pallet: 9 rolls Regulations • In accordance with standards: UNE-EN 13249:2001, UNE-EN 13250:2001, UNE-EN 13251:2001, UNE-EN 13252:2001, UNE-EN 13253:2001, UNE-EN 13254:2001, UNE-EN 13255:2001, UNE-EN 13256:2001, UNE-EN 13265:2001. Certified with CE marking No. 0099/CPR/A42/0093 – 0094 – 0095 – 0096 – 0097.

DRENTEX IMPACT GARDEN is a sheet drain made up of a three-dimensional polystyrene (HIPS) structure perforated or not, with a polypropylene geotextile on one or both sides. Advantages   DRENTEX IMPACT GARDEN sheets made up of three-dimensional polystyrene (HIPS) structure (dimple shaped) guarantee the high drainage capacity over the years, due to its elevated compressive resistance and almost none deformation · The non-woven propylene geotextile acts as a water filter to prevent soil from blocking drainage, while the polystyrene dimples guide and drain off the water. The entire system drains off water and protects the waterproofing on walls, foundations, etc. · A stable, reliable, rot-, root- and fungi-proof drainage system. · Because all the dimples are connected directly to the geotextile structure, high compressive strength is provided to ensure the drainage volume is not reduced by pressure from the soil. · Easy to transport and install. INSTALLATION · Vertical and horizontal drainage of walls and floors: low or high water collection. · Horizontal drainage of pedestrians or wheelled trafficable roof decks: high water collection. · Extensive green roofs and areas drainage. · Intensive green roof and areas drainage. · The range of drainage for green roofs, higligths DRENTEX IMPACT GARDEN 500, it is specially used on areas on risk of floating, on a low slope surface (< 1%) or located on high rainfall intensity geographical location; and DRENTEX IMPACT GARDEN PLUS for highly performances and elevated water retention depend on the plants require. Storage   Roll: 1,25 m x 32 m/ m² Roll: 40 m² Pallet: 80 Regulations · The product is CE marked according EN 13252:2001 + A1:2005. Holds the certificate Nº 0799-CPD-41 · Quality Management System according to the requirements of ISO 9001:2008 standard