Testing Apparatus Dealers in Rajendra Place, Delhi

Product Code: EKE 895This test is performed to measure the short-term strength of an installed Rockbolt under field conditions. The strength is measured by a pull test in which bolt head displacement is measured as a function of applied bolt load to give a load- displacement curve. This test is usually employed to assess the performance of the Rockbolt anchor resulting out of the quality of material used for manufacture of Rockbolt and installation method used. The test equipment consists of a manually operated hydraulic pump connected to hydraulic jack, having a high strength test rod, coupled to the Rockbolt under test. The anchor is tested by measuring the load until a total displacement greater than 40 mm has been recorded or until the bolt yield or fractures, if this occurs first. The readings of displacement are taken in increments of approx. 5 kN load or 5 mm displacement whichever occurs first. The rate of load application should be in the range 5- 1 0 kN/min. Readings are only taken after both load and displacement have stabilised. The time required for stabilisation should be recordedDetails Pullout Test Apparatus 500 kN (50 Tonnes) Consists of following: EKE 89001 Hydraulic Centre Hole Jack 500 kN (50 Tonnes) capacity with 54 mm Centre Hole, 150 mm Ram Travel, Double Acting EKE 89005 Hand Operated, two Stage Pump EKE 89007 Thermoplastic Hose, 6m long. with pair of quick couplings EKE 89010 Load Gauge 150 mm dia, 500 kN x 5 kN EKE 89011 Reaction Frame 500 kN capacity with 90mm hole at base EKE 89012 High Strength Test Rod, 40 mm dia EKE 89015 High Strength Coupling, having RH thread to suit Test Rod on one end and LH thread to suit 20mm dia Rockbolt on the other end EKE 89016 High Strength Coupling, having RH thread to suit Test Rod on one end and LH thread to suit 25mm dia Rockbolt on the other end EKE 89017 High Strength Coupling, having RH thread to suit Test Rod on one end and LH thread to suit 30mm dia Rockbolt on the other end EKE 89018 High Strength Coupling, having RH thread to suit Test Rod on one end and LH thread to suit 32mm dia Rockbolt on the other end EKE 072- Dial Gauge, 0.01 x 25 mm

Slump test apparatus, The slump cone is filled with freshly mixed concrete and is tamped with a tamping bar in three or four layers. The top of the concrete is leveled off with the top of the slump cone, the cone is lifted vertically up and the slump of the sample is immediately measured. Base has cleats on its underside to help dig into the ground surface Positive clamping of slump cone to the base while filling and rodding the concrete A combination swivel carrying handle also doubles as the datum making the conventional and somewhat awkward measuring procedure of using a foot rule and a datum bar, a thing of the past Supplied complete with base plate, having cleats and swivel handle and EKE 345 Tamping Rod of 16 mm dia x 60 cm long.

We are offering flammability test apparatus. The flame-retardant characteristics of electric cables depends upon, raw material used during manufacture, design & external circumstances.several tests have been designed to determine the flammability of the material used in cable or even the fire properties of bunch of cables.

• Brand Name: Steco
• Capacity: 5000 Kg
• Dial Gauge: 0.01mm X 25mm travel
• Mould Size: 100 mm dia x 127.3 cm height X 1000 cc
• Deformation: 0-5 mm + / - 0.0001 mm

Cord Retention Test Apparatus for Plugs and portable socket-outlets shall be provided with a cord anchorage such that the conductors are relieved from strain, including twisting, where they are connected to the terminals or terminations, their covering being protected from abrasion. The plugs attach with cable and connector is subjected to pull test as per IEC 60884 standard.  The plug is loosely hung from the fixture and a dead weight is attached as per the IEC 60884 standard.

We are leading supplier of huge range of Salt Spray Test Apparatus.

KEWIL Ring and Ball Apparatus Ring and ball apparatus is meant for determining soft point of bitumen. Using various scientific principles it is also used in petroleum industry, construction projects, paint industry etc. The ring & ball apparatus is used to determine the temperature at which a sample of bituminous material loaded by a steel ball of 9.5 mm diameter, drops a specified distance when heated under specified conditions. It is used to determine softening point of bitumen.

The firm is known for building efficient apparatus for carrying out the Marshall Stability Test. The Marshall Stability Test Apparatus is applicable to hot mix designs by availing bitumen and aggregates. In this procedure, the resistance to plastic deformation of cylindrical specimen of bituminous mixture is calculated when the same is loaded at periphery at 5 cm per min. The two prime features of the Marshall method of designing mixes are Density : Voids AnalysisStability : Flow Tests This test method is used in the design and evaluation of bituminous paving mixes. The test method is widely used in routine test programmers for paving works. Specifications A loading unit motorized, capacity 5000kgf with two telescopic pillars and an adjustable cross head. The Limit switches are attached inside to regulate the upward or downward movement of the pillars. On off reversing switch and indicator lamps are on the front side while a hand wheel to manually displace the pillars is on the right side. The load frame has fixed speed of 5.80cm per minute, which is operated on 230 volts AC3 Specimen mold 10.16cm I.D. x 7.6cm high with base plate and extension collarOne Kit for specimen extraction that consists of one each load transfer bar, steel ball and specimen extracting plateOne number compaction pedal with specimen mold holder1 Breaking head assembly with provision to fix flow meterThe Marshal Stability of mix can be defined as a maximum load carried by a compacted specimen at a standard test temperature of 60oC

The standard outfit comprises of the following items. Loading unit, maximum capacity 20kg/cm2. Having a loading yoke connected to a lever arm with a counter balancing adjustment and having a lever ratio of 1:1 the whole assembly being mounted on a sturdy steel frame stand. The loading unit is so designed that it can be used for consolidation cells of different diameters as well as different dia. floating ring type consolidation cells. Fixed ring type Consolidometer (Odeometer) cell assembly for testing 60mm dia x 20mm thick specimen comprising: Fixed ring for specimens 60mm dia x 20mm thick with guide ring. Top and bottom porous stones for 60mm dia specimen. Perforated pressure pad, channeled base with water inlet and gasket Flanged water jacket, water reservoir with plastic tube and pinch cock. Set of weights to give a pressure of 10kg/cm.sq. On 60mm dia specimen, comprising : 7 nos. 0.05 kg/cm2, 5nos. 0.1 kg/cm2, 6nos. 0.5kg/cm2, and 5 nos. 1.0 kg/cm2. Supplied complete as above but without dial gauge. Accessories : Dial gauge 0.002 mm x 5mm. Extension piece, 40 mm long, consolidation test forms pad of 50 for one dimensional consolidation.

Loading Unit, maximum capacity 20 kg/cm2 consisting of a loading yoke connected to a lever arm with a counter- balancing adjustment and having a lever ratio of 1:10, the whole assembly being mounted on a steel frame stand. ·         Consolidation cell assembly, fixed ring type for testing 60 mm dia x 20 mm thick specimens comprising: ·         Fixed ring for specimens 60 mm dia x 20 mm thick with a guide ring. ·         Top porous stone for 60 mm dia specimen. ·         Bottom porous stone for 60 mm dia specimen. ·         Pressure pad, perforated ·         Channeled base with water inlet. ·         Gasket. ·         Flanged water jacket, ·         Set of weights to give a pressure of 10 kg/cm2 on 60 mm specimen. Comprising: 7 off 0.05 kg/cm2, 5 off 0.1 kg/cm2, 6 off 0.2 kg/cm2, 6 off 0.5 kg/cm2, and 5 off 1.0 kg/cm2. ·         Water reservoir with plastic tube, T-connection and pinch cock. ·         Dial gauge, 0.01 mm x 25 mm travel

  The Blaine air permeability apparatus is used to determine the fineness of Portland cement in terms of the specific surface expressed as total surface area in square centimeters per gram of cement. The Blaine apparatus draws a defined volume of air through a prepared bed of cement of defined porosity. We manufacturer, Supplier & Exporter of Blain Air Permeability Apparatus from india. Due to its high quality and features Blain Air Permeability Apparatus is highly demanded in the market.

Unique design of ventilation keeps the surface of the instruments from being Burnt even when the instruments i.e. Oven Temperature maintained at 200°C, Kanthal A-1 Super quality coil shaped & Air heater tubular model wound on sideon the back of the Oven for better accuracy, Toughened Glass view window to observe Test the material without disturbing the Temperature condition of the chamber.

• temp.: 200°C ±0.5°C.

SIGMA Thermal Stability Test Apparatus is used to measure check Thermal stability of PVC insulation & sheath of Electric cables as per IS:5831. Measures Thermal stability time in minutes required to change the pH value of 5 to 3 of a universal indicating pH paper placed in a glass tube containing sample and heated in a PID controlled heating chamber at specified temp. of 200°C ±0.5°C.

• Type: Bitumen Testing Machine
• Certification: Iso 9001:2008
• Weight: 100-500kg
• Voltage: 110V, 220V, 380V
• Condition: New
• Automatic Grade: Automatic
• Power: 3-5kw, 5-7kw
• Driven Type: Electric
• Warrenty: 1 Year

We are instrumental in offering our clients an exquisite range of corrosion test apparatus. The products are fabricated by the proper utilization of high quality raw materials, that are procured from the most reliable vendors present in the market. Apart from this, the offered product range is available to the clients at the most market leading price range. features: high performance seamless finish precisely-engineered cost-effective optimality.

• Material: Steel, Granite
• Size: 38 mm
• Resolution: 0.001 mm

leak test apparatus, industrial electric ovens, Ultrasonic Bath