Testing Apparatus Dealers in Saket, Delhi

For determining the triaxial shear strength of soil specimens of 28mm diameter. The length to diameter ratio of sample is 1:2 Specification : One loading unit, for single unit, for single cell mounting, capacity 5 tonnes. Supplied with motorised load frame. The loading unit is supplied with one dial gauge bracket. One Triaxial Cell for 38 mm dia specimen, stationary bushing. Lateral Pressure assembly. 0-10kg/cm sq. complete with foot pump and rubber hose. One dial gauge 0.01 mm X 25 mm for strain measurement. One high sensitive Proving Ring, capacity 200/250 kg with Calibration Report and carrying case. Accessories: High sensitivity Proving Ring, capacity 1000 kg. complete with calibration report and carrying case. Salient Features Triaxial Shear Test Apparatus (Motorised) Single Speed : Same as above, supplied with motorised load frame. The load frame supplied with this outfit is bench mounting type motorised load frame of 5000 kgf having constant rate of strain 1.25 mm/min. Suitable for operation on 230 Volts A.C. Triaxial Shear Test Apparatus (Motorised) 3 Speed : Universal Triaxial Shear Apparatus (Motorised) 6 Speed : For determining the triaxial shear strength of soil specimens of 38 mm, 50 mm, 75 mm and 100 mm. Consists of: One load frame 5000 kgf motorised, constant six rates of strain type, giving the following rates of strain. 1.25, 0.25, 0.05, 0.01,0.002,0.0004 mm/min. Load frame is supplied with a dial gauge bracket. Universal Triaxial Cell (Stationary Bushing) 10 kg/cm.sq. One Lateral Pressure assembly 0-10 kg/cm.sq complete with foot pump and rubber hose. One high sensitivity Proving Ring capacity 1000 kg.One strain dial guage 0.01 X 25 mm. Suitable for operation on 230 Volts A.C.

• MOTOR SPEED: 0 TO 1500 RPM (APPROX)
• EQUIPMENT WEIGHT: APPROX. 2KG
• TPI RANGE: 1 COUNT FOR TPM/0.250 COUNT FOR TPI

Clamp the yarn in the clamp fixed on the motor shaft. A guide is provided on the clamp for easy clamping. Pull the other end of yarn through the clamp on the moving crosshead had while clamping ensure that yarn is clamped for proper test length and yarn is free and under correct tension of weight. This is necessary to have uniform length of yarn between the clams under fixed tension to get proper repeatability of the results. Select SZ switch in S or Z position depending upon type of yarn. Put the main switch ON and press the ‘RESET’ push button to ensure zero reading on the digital display unit. Select the motor speed to high speed position. Select ‘NORMAL’ position for initial operation. Start the motor using ‘START STOP’ switch. The motor will now start untwisting the yarn and DIGITAL DISPLAY will start counting. After reaching approx. 90% of expected TPM reading, it is recommended to lower the motor speed to minimum possible to get better results. By using ‘ADJ knob’ the motor can be run in very slow to moderate slow speed, or if motor stops completely test can be run manually by pushing motor shaft by hand.The instrument carries a guarantee for 12 month for free repairs against any manufacturing defects. However this guarantee is void in case of any physical damage or attempted repairs at customer’s end. The instrument is required to be sent to our works at customer’s expenses for claiming warranty services.

Used for detecting the presence of corrosive sulphur in petroleum products.The apparatus consists of a bath either dual purpose (500C & 1000C) or a boiling bath (1000C only) without stainless steel copper strips of definite size 6 or 18 test tubes can be accomodate in each type of bath with different temperature regulation system to operate on 220 volts AC. mains.

IR Beaker Dyeing Machine, HTHP Beaker Dyeing Machine, Crease Recovery Tester