Charpy Impact Testing Machine Dealers

Features : For Charpy tests on various materials Strictly conforms to ASTM-E-23- Current Standard. Works on Pendulum Principle, Difference between height of drop of Pendulum before Rupture and Height of rise after Rupture of specimen is directly proportional to impact energy absorbed by specimen on large dial./ Digital readout. Two hand Pendulum release operation for operator safety. Large safety guards on both sides of Pendulum. NIST approval of machine with samples from NIST, USA can be arranged Motorised with higher capacity impact machine is also available Standard Accessories (For Model FIT-300-ASTM) Charpy Striker-1No. Charpy Support Block-1set Specimen Setting Gauge (For Charpy)-1No. Set of Spanners-1Set Foundation Bracket-1No. Optional Accessories Self centering tong for Charpy test Specimen. (Usefull particularly for carrying out tests at sub zero temp.) Sub zero temp.bath with digital calibrated temperature indicator. GO-NO GO, Gauges for specimens confirming following parameters within specified limits. Centre line of notch from both ends Angle of V notch Depth below standard V notch Cross section of 10 x 10 mm specimen. Miling cutter for V notch Lateral Expansion gauge as per ASTM-E-23 Standard Impact specimen for verification of machine from NIST, USA (We also undertake calibration of machines of any make, as per ASTM-E-23 Including approval from NIST, USA)

• Power: Without electricity
• Weight: 30kg
• Application: Hard plastic
• Size: 550*400*690mm
• Test Angle: 150 degree

Charpy impact testing involves striking a standard notched specimen with a controlled weight pendulum swung from a set height. The standard Charpy-V notch specimen is 55mm long, 10mm square and has a 2mm deep notch with a tip radius of 0.25mm machined on one face. The specimen is supported at its two ends on an anvil and struck on the opposite face to the notch by the pendulum. The amount of energy absorbed in fracturing the test-piece is measured and this gives an indication of the notch toughness of the test material. The pendulum swings through during the test, the height of the swing being a measure of the amount of energy absorbed in fracturing the specimen. Conventionally, three specimens are tested at any one temperature and the results averaged. Charpy tests show whether a metal can be classified as being either brittle or ductile. This is particularly useful for ferritic steels that show a ductile to brittle transition with decreasing temperature. A brittle metal will absorb a small amount of energy when impact tested, a tough ductile metal absorbs a large amount of energy. The appearance of a fracture surface also gives information about the type of fracture that has occurred; a brittle fracture is bright and crystalline, a ductile fracture is dull and fibrous. The percentage crystallinity is determined by making a judgement of the amount of crystalline or brittle fracture on the surface of the broken specimen, and is a measure of the amount of brittle fracture.

• Release angle of pendulum: 150 degree.
• Range of scales: 0-2.71 Joules, 0-5.42 Joules, 0-10.84 Joules, 0-21.68 Joules and 0-25.00 Joules.
• Minimum resolution on scale: 0.02 Joule, 0.05 Joule, 0.1 Joule, 0.2 Joule and 0.2 Joule respectivel

Both Charpy and Izod impact testing are popular methods ofdetermining toughness or impact strength of a Composite Material. Tosum up, these tests measure the total amount of energy that a materialis capable to absorb. This energy absorption is directly related to thebrittleness of the material.

• Weight: 100kg
• Phase: Manual
• Material: Metal
• Voltage: Manual
• Power: 230
• Automation Grade: Manual
• Automation Grade: Automatic
• Brand Name: TEI
• Finishing: Polished
• Condition: New
• Country of Origin: India
• Display Type: Round Scale
• Product Type: Spring
• Capacity: 3000j
• Minimum Order Quantity: 1 Piece

Charpy Impact Testing Machine The Charpy impact testing machine we offer is designed to conduct Charpy and Izod tests. Our machines come with the pendulum mounted on the anti friction bearings. The machine model comes with two starting positions, the upper one for the Charpy tests and the lower one for the Izod testing. The machine is designed to read the specimen from the maximum pointer position on the dial scale. When you are using the machine, you can change from one striker to another simply by fixing the new striker into its position. Most of our machines and instruments are developed based on the national as well as international standards. Therefore, you will obtain the best quality products for the money you spend. Before you order the Charpy impact testing machine from our store, you will find all the specifications and details about the machine. The model provided by our company comes with interchangeable strikers and front guard for safety. The common specimen holder is also provided with the model for Charpy and Izod test. Salient features: • 2J scale graduation • Pendulum drop angle of 140 degrees for Charpy test and 90 degrees for Izod test • Pendulum effective weight of 21.300 Kg for IZOD test and 21.400 Kg for Charpy test • Striking velocity of the pendulum is 3.857 m/sec for Izod test and 2.45 m/sec for Charpy test • Pendulum impact energy is 168 J for IZOD test and 300J for Charpy test • Scale graduation of 2J • Maximum permissible loss by friction 0.50% of impact energy

Charpy Test : The charpy test piece rests on alloy steel support anvils, fitted on the base of the machine rigidly held in position by Allen screws. End stopper is provided for quickly and accurately locating the test piece centrally between the supports.Izod Test : The Izod test is clamped vertically in Izod support fitted on the base of the machine. The support is provided with a machined vertical groove to suit the test piece size. The front clamp piece and the Allen screw enable clamping of the test piece in correct height with the help of Izod setting gauge supplied.Model IT-30 ( ASTM ) : This impact tester offered with 300J energy exclusively for Charpy test confirming to ASTM E-23. This machine is geometrically checked in the works to the more stringent requirements of the American standard. The accuracy of the machine is then verified by PROOF TEST by testing standard test specimens supplied the NIST, USA. Two sets ( Low & high energy-1 Set (4 Nos.) each.) must agree with the normal values within certain tolerance specified.

• Brand Name: FIE
• Material: Mild Steel
• Driven Type: Electric
• Power: 1-3kw
• Weight: 375 Kg
• Automation Grade: Manual
• Pressure: Low Pressure, High Pressure
• Type: Impact Testing Machine
• Country of Origin: Made in India
• Model Name/Number: IT - 30
• Capacity: 300 J/168 J
• Power Source: Electric

Features For charpy tests on various materials. Strictly conforms to ASTM-E-23-2007 specifications. Works on pendulum principle. Difference between height of drop of pendulum before rupture and height of rise after rupture of specimen is directly proportional to impact energy absorbed by specimen and is indicated by a pointer on a large dial for Model-ASTM & on Digital Display for Model- ASTM (D). Single stand design which facilitates fast and easy positioning and centering of specimen which is a basic requirement of sub-zero testing. Unique spring loaded braking system for smooth and jerk free braking. NIST approval of machine with samples from NIST-USA. Can be arranged. Digital version of ASTM model will be available soon. OPTIONAL ACCESSORIES: Self centering tong for Charpy test specimen (useful particularl for carrying out tests at sub zero temperature). Sub zero temperature bath with digital temperature indicator. Go: No-Go gauges for conforming the following parameters of specimen-within the limits specified by the standard. Center line of notch from both ends. Angle of V notch. Depth below standard V notch Cross section of 10x10 mm specimen. Milling cutter for V notch. Charpy & Izod notch (V&U) broaching machines. Lateral expansion gauge as per ASTM-E-23. Standard impact specimen for verifivcation of machine from NIST-USA (we also undertake calibration of the machine as per ASTM-E-23 including approval from NIST-USA).

• Ranges: 0-2.71 J 0-5.42 J 0-10.84 J 0-21.68 J

The resistance to breakage by flexural shock of plastics and Electrical insulating materials as indicated by the energy extracted from standardized pendulum type hammers mounted on standardized machines in breaking standard specimens with pendulum swing. The energy absorbed per unit of specimen width is reported in joules.

The Izod / Charpy Impact Test is used to measure the relative susceptibility of standard test specimen to the pendulum type Impact load.   The "Saumya" Izod / Charpy Impacto Meter is having a energy range from one joule to twenty-five joules in five different scales.     STANDARDS:   ASTM D 256 AND OTHER EQUIVALENT STANDARDS     APPLICATION:   Impact Strength is the Mechanical property of polymer and as molecular flexibility plays an important role in determining the relative toughness of materials. For any molded plastic this test plays an important roll.   USP:   The "Saumya" Impacto Meter is designed and built according to National and International Standards. Dial with clear and five different scales for energy selection.   The "Saumya" Digital Imecto Meter is having versatile features with high accuracy to measure Izod / Charpy Test upto range of 1 to 25 Joules.   Interchangeable parts for Izod and Charpy test.   Two hammers each for both the test with extra load attachments.  

• Brand Name: Technogroovy
• Power: Electronic
• Model Number: TG 105
• Place of Origin: India

Digital Izod / Charpy Impact Tester, Analog Izod / Charpy Impact Tester, Impact Tester for Plastic Pipes  

• • Initial potential energy (Joules): 300
• Resolution for AIT-300-ASTM (D): 0.5

• Works on pendulum principle, difference between height of drop of pendulum before rupture and height of rise after rupture of specimen is direclty proportional to empact energy absorbed by specimen and is indicated by a pointer on a large dial for model: AIT-300-ASTM & on display for model: AIT-300-ASTM (D) • Single stand design which facilities fast and easy positioning and centering of specimen which is basic requirement of sub-zero testing • Unique spring loaded braking systems for smooth and jerk free braking • NIST approval of machine with samples from NIST-USA, can be arranged • Model: AIT-300-ASTM (D) is a digital version of model: AIT-300-ASTM

Charpy impact tester is manufactured as per ASTM D 6110 and ISO standard. These models are used by injection moulds & engineering plastic manufacturers. Also charpy impact tester has wide importance in testing polypropylene pipe manufacturing industry for testing the PPR pipe. Notch cutter is a requirement for making notch on charpy impact samples. Thus notch cutter is also supplied along with this equipment. Charpy impact tester and Izod impact tester are those material testing equipment that are used to check the axial impact on molecular structure of material and thus measure the failure of polymers under impact. condition.  Specification:  Capacity : Up to 25.00 Joules.Release angle of pendulum: 150 degree.Range of four scales : 0-2.71 Joules, 0-5.42 Joules, 0-10.84 Joules, 0-21.68 Joules and 0-25.00 Joules.Minimum resolution on scale: 0.02 Joule, 0.05 Joule,0.1 Joule, 0.2 Joule and 0.2 Joule respectively. Paint : Powder coated. Power : 230 Volts, 50Hz, single phase. Direct display through microcontroller: Impact strength in joules/meter and kg-cm/cm.Graphic display and printout through PC: Impact energy Vs Angular displacement graph and numeric reports consisting of values for impact strength as per ASTM standard, ISO and IS standard in different units could be obtained by attaching a printer to the PC.  

Applications To prepare correct "V" or "U" notches in Charpy/Izod impact test specimens by means of an accurate multiple-toothed broach Advantages Most simple and accurate Specifically drafted for ferrous & nonferrous material . Skilled operator not required Expensive machines not required Precision regrinding of tools eliminated Less power requirement Very compact in size Precisely cuts the desired notches as per respective standard in just single pass within few seconds. No efforts, all by motorized operation. Just press a push button to start. Equipped with broach guard for safety. Easy removal & assembly of broach Longer broach Life. Ball Screw for uniform cutting action. Hardness rods with LM bushes for smooth motion. Micrometer for fine feed and adjustment Excellent notch finish & Excellent Repeatability. Front door window access for observing the operation Notches confirm to the following standards ASTM A370, BS 131: Part 1: 1961 / Part 2&3: 1972, DIN: 50115, IS/1598/1977

The pendulum Impact Tester, Model IT-30 is designed for conducting Izod, Charpy test. The test methods confirm to BS : 131 : Part 4-1972 (Amended 15 Aug. 1993) BSEN : 10045-2 : 1993 The Pendulum is mounted on antifriction bearings. It has two starting positions, the upper one for Charpy & the lower one for Izod testing. On release, the pendulum swings down to brake the specimen and the energy absorbed in doing so is measured as the difference between the height of drop before rupture of the test specimen and is read from the maximum pointer position on the dial scale.

• Material: Iron
• Type: Testing Machine

Our payment procedures are hassle free, safe, and legal. We do not impose hidden charges while creating the invoice and ensure your money is transferred securely from you to us. We have segregated our infrastructural facility into several units including packaging unit wherein we meticulously pack our products to ensuring hassle free deliveries.

We offer mechanical equipment.

• Pendulum release angle: 150 degree
• Maximum Capacity: Up to 25.02 Joules

The instrument “Charpy Impact Tester” comprises of a pendulum of specific length and weight which is dropped from a standard height to determine the effect of impact pressure on the notched sample of material. The energy which is applied to the material can be changed according to the specifications of the sample by changing the height and weight of the hammer before commencing the test.

The pendulum is dropped from a specific height to put an impact on a notched sample. The notch used in the test must be of regular dimensions as it has a great impact on the test results. The size of the samples also has a great impact on the test results hence it is essential to choose standard sizes of the specimen. With the help of the Charpy Impact Test, one can easily analyze the strength of material. The quantitative results of the test give the understanding of the amount of force that a material can absorb when it reaches the point of fracture or failure. The qualitative results of the test procedure can provide information about the ductility of the materials being tested.

Impact tests are designed to Measure the Resistance to failure of a Material to a suddenly applied force at different Temperature. The test measures the impact energy, or the energy absorbed prior to fracture. We are offering an Izod Impact Test and Chary Impact Test. Machine is calibrated by NABL Calibration agency and certified by NIST. Today it is utilized in many industries for testing materials, for example the construction of pressure vessels and bridges to determine how storms will affect the materials used

Charpy Impact Testing Machine, Shear Fatigue Tester

Charpy Impact Testing Machine, Welding Machine, Lathe Machine

Charpy Impact Testing Machine, Wrap Reel, Conditioning Chamber

Gsm Round Cutter, Secure Seal Tester, Torque Tester, Tensile Strength Tester