Slump Cone
Get Price Quote
We are offering slump cone.
Plate Bearing Test Apparatus
1 - 10 Per Piece
1 Piece (MOQ)
Standad Used : IS 1888 1962, ASTM D 1194, BS 13779 This is for estimating the bearing capacity of shallow foundations in situ and for the design of flexible pavement. In the test procedure a steel plate is subjected to gradually increasing load and settlements of the plates recorded. Specification : The out fit consists of 50 tonne hydraulic jack with separate pumping unit fixed to it a 0 - 500KN x 0.5KN. Pressure gauge and flexible metal pipe 5 mtr. long Special ball and socket arrangement Extension rod 12mm dia x 25 cm long Magnetic base with female thread on top for holding extension rod Top end plate, 50mm, dia with male thread for fitting onto the extension rods and positioning the dial gauge plunger Column 15cm dia x 25cm long with flanges complete with four bolts and nuts Column 15cm dia x 50cm long with flanges complete with four bolts and nuts Bridge support of welded steel angle construction, 5 mtr. Span and stands approximately 30 cm. High. Fitted with two quick release clamps a for positioning and holding the dial bracket
Best Deals from Civil Engineering Test Equipment
1918 & 1916 Microprocessor Dissolution Test Apparatus
Get Price Quote
1 Piece (MOQ)
Microprocessor Dissolution Test Apparatus is a solid state instrument designed for the determination of active drug ingredient in any pharmaceutical formulation, tablet or capsule as per IP and USP specifications. This apparatus evaluates adequate bio-availability and provides necessary information to formulate in the development of therapeutically optimum dosage forms. The instrument is designed and manufactured for pharmaceutical industries. It is used in quality control and R & D to determine compliance with the dissolution requirement of the Tablet and Capsule as per USP/IP standards. Instrument uses the latest microprocessor technology and advanced engineering techniques so as to give enhanced accuracy and reproducibility. The system has user friendly prompts, which guide you throughout the measurement process. System is equipped with 4 line alphanumeric LCD display with backlit and 19 soft touch membrane type keys that provides a convenient interface for entering the data. Independent stirrer and platform keys on the front panel allow the user to easily start/stop stirrer movement or displacement of platform in the required direction at any time. The instrument has the storage facility for 200 samples. The samples being analyzed are automatically stored in the memory in different batch and sample numbers. The system has three programming modes i.e. Routine, Sustain and Control mode. It has the facility for setting up 20 different test methods using Routine and Sustain modes which are retained in the memory even when the power is switched OFF. Provision has also been made for attachment of any dot matrix printer with centronics interface so that any of the stored setups/results can be printed. The unit is provided with dissolution vessel with cover, having necessary arrangement to hold temperature sensor and the same is placed in the sturdy, acrylic water bath. The large spread out stainless steel heater ensures perfectly uniform heating. The instrument has dual channel temperature system with sensors to monitor the test temperature of dissolution vessel as well as that of the water bath. The motorized platform’s (stirrer unit) up/down movement of the instrument improves the accessibility for sampling. Stirrer speed is accurately controlled and maintained at ±1 rpm by microcontroller as per IP, USP specifications. The elapsed time for the current ongoing test is retained in the instruments memory. In case of power failure during the run mode, when the instrument is switched On again, the user has the option to run the test from the point of the power failure. Features 8 Station (Model – 1918) 6 Station (Model – 1916) Complies with USP, IP specifications Extremely Useful for Pharmaceutical Labs Highly Accurate and Easy to Operate Programmable Stirrer Speed Control i.e. (25 – 300 RPM) 20 x 4 Line Alphanumeric LCD with Backlit 19 Soft Touch Membrane Type Keys Three Programming Modes i.e. Routine, Sustain and Control 20 Independent Programmable Setups for Routine and Sustain Mode with Storage Facility 200 Samples Storage Facility Printer Attachment Facility Audio Visual Indicators for System Status Easy to Empty & Clean the Water bath with Bottom Drainage Continuation of Last Sample Run in case of Power Failure
leak test apparatus
42,000 Per Piece
1 Piece (MOQ)
Jar Test Apparatus
Get Price Quote
1 Piece (MOQ)
Fume Hood
Get Price Quote
Fume hood can reduce or eliminate exposure to volatile liquids, dusts, and mists The fume hood is often the primary control device for protecting laboratory workers when working with flammable and/or toxic chemicals. Hoods protect workers by: Containing vapors, dusts, gases, and fumes generated within the hood, and removing them as air flows into the hood and then out via the laboratory exhaust system. Features : Outer body of fume hood is made of mild steel duly powder coated Work table is made of 0.8 mm thick stainless steel 304 sheet or 16 mm thickness Granite slab. A sliding door of aluminum frame fitted with full view clear glass moves vertically up/down with counter balanced weight operated by steel rope Hose is provided with fluorescent light for easy working in the chamber and a storage cabinet is also provided for storing of material A 6/16 Amp socket and switch is also provided in hood for providing electric supply to small devices – hot plate, magnetic stirrer, etc used in hood The control panel is fitted with on/off switches for mains, motor-blower, tube light and socket Machine requires 230V, Single Phase, 50 Cycles, AC power supply Optional : Fume Duct and exhaust line – PVC or HDPE as required Inner chamber made of SS 316 and outer made of SS 304 Small SS sink or PP sink with water tap and water drain outlet fitted on work table Colour coded utility service remote control valve 2 nos for air (nitrogen, oxygen, etc) & water knobs are mounted on front side of hood outside the working chamber. Nozzle is fitted inside the chamber. Stream lined airfoil made at the bottom of hood work table opening for smooth flow and avoiding turbulence inside the hood. SS grid fitted inside the work chamber Inner Cabinet Dimensions : 2’ x 2’ x 3’ 3’ x 2’ x 3’ 4’ x 2’ x 3’ 5’ x 2’ x 3’ 6’ x 2’ x 3’
Bulk Density Test Apparatus
6,500 Per Piece
1 Piece (MOQ)
Bulk density test apparatus as per I.S. 2386 Part IV. Determines bulk density or unit weight of aggregates. Specifications: Calibrated cylindrical measures of sheet iron with handles. Consists of 3 measures one each 3 litres capacity, 15 litres capacity and 30 litres capacity. Complete with one tamping rod, round, 16mm dia and 600mm long, one end rounded.
Digital Penetrometer
8,500 Per Pcs
Dynamic Pile Load Tester
150,000 - 445,000 Per No
1 Piece (MOQ)
Standard Penetration Test Apparatus
Get Price Quote
1 Piece(s) (MOQ)
Cone Penetrometer
Get Price Quote
1 Set(s) (MOQ)
We are offering cone penetrometer. The proving ring penetrometer is a cone type of penetrometer which can be used in a number of applications. It serves as a rapid means for determining the penetration resistance of soils in shallow exploration work. The reading obtained in this method maybe correlated to standard or modified compaction data for compaction control in the field. Trafficability relationships can be obtained for quick field evaluation of sites.
Direct Shear Apparatus
Get Price Quote
1 Piece (MOQ)
Electronic Direct Shear Apparatus motorized with single speed with software. As per IS :2720 (PART 13) 1986 / IS : 11229 - 1985, Supplied without PC/Laptop or Printer.
Proctor Compaction Test Apparatus
Get Price Quote
We make sure; our products are produced using top grade materials sourced from reliable vendors only. Deeply rooted in New Delhi(India), we are indulged in the process of providing products to any required destination with ease.Specifications : Weight of the hammer(hammer weight) - 2.5Kg Diameter of the hammer - 50mm Drop - 300mm Dimension of the compaction mould - 100”127mm
Four Pin Soil Resistivity Meter SR-2
Get Price Quote
The Tinker & Rasor SR-2 Soil Resistivity Meter is a highly accurate and easy-to-use soil resistivity instrument for use with the 2-pin and 4-pin (Wenner) methods of soil resistance measurement. A pin selector switch allows choosing between 2-pin and 4-pin tests without removing cables. Model SR-2 provides easy resistance readings with a digital 4-12 digit display, push-button operation, and an easily adjusted Ohm to MOhm range selector. The display will show in the correct range. Multiply reading with pin spacing multiplier for Ohm-cm.
Disintegration Test Machine
Get Price Quote
1 Piece (MOQ)
SIS – 1342 The instrument is designed for accurate estimation of disintegration time of tablets/capsules. It is assembled in painted sheet metal cabinet with chemical resistant epoxy coating, fitted with superior quality constant speed sturdy motor. The guide discs and strokes are confirming to pharmacopoeia Standards. SPECIFICATION : Displacement:55mm RPM:30 Drive:1/8 HP Heater:125 Watt. Power:AC/230 volt Single Phase. OPTIONAL 1)Water bath system instead of Hot Plate. 2)Digital Temperature Controller in Water bath System only. 3)Digital Time Totaliser 4)GMP Models also available (Body made of SS 304)
Slump Test Apparatus
Get Price Quote
1 Piece (MOQ)
leak test apparatus
Get Price Quote
We are offering leak test apparatus
Glow Wire Test Apparatus
28,500 - 35,000 Per Piece
1 Piece(s) (MOQ)
Shrinkage Bar Mould
Get Price Quote
1 Piece(s) (MOQ)
cbr testing machine
Get Price Quote
10 Piece (MOQ)
Post Free Ad
4.0
