Conformal Coatings Dealers

• Brand Name: SEAGEL
• Material: Silicon
• Surface Finishing: Polished
• Color: Transparent
• Form: Liquid
• Speciality: Chemical Resistant, Waterproof, Water Resistant, Solvent Resistant, Optimum Quality
• Usage: Industrial Use
• Pattern: Plain
• Grade Standard: Technical Grade
• Packaging Type: Spray/metal can
• Packaging Size: 5 ltr / 500 ml
• Type: Conformal Coating
• Shelf Life: 1Year
• Country of Origin: India

• Packaging Type: 100 sets
• Color: Blue
• Material: Silicone
• Thickness: 3.5-4mm
• Application: Electric Board Use
• Usage/Application: Masking cap for conformal coatings in PCB boards

Here are three simple reasons why you can save up to 80% of your costs when using reusable masking boots compared to other conformal coating masking methods: Masking time is reduced because using boots can be 4-5 times quicker than masking tape. De-masking time is reduced since it is much quicker to remove boots Masking boots don’t leak. Therefore, there is less repair due to masking mistakes. This means you can save a lot of money very quickly when switching to masking boots.Powerful 19.2V High Torque Motor • 6,000 PSI (413 BAR) Output Grease Pressure • Grease Output upto 3 oz. (85 gms) / minute in free flow • Automatic Air Bleeder & Bulk Loader • Automatic Pressure Release Valve • 30” High Pressure Hose with Spring Guard on both ends (prevents hose from kinking) • High Pressure Grease Coupler • Standard 1.5Ah Ni-Cd Battery Pack • An additional 1.5Ah Ni-Cd Battery Pack for un-interrupted greasing • One Hour Quick Charger (each battery charge provides power to dispense upto 6 Grease cartridges in free flow condition) • Comes with Blow Moulded Case for conveniently storing when not in use

PCB Conformal Coating, Specialty Lubricants, Contact Cleaner, Mold Cleaners

• Packaging Type: Paper Box
• Coating Thickness: 0.5-1mm, 25-75 micron
• Speciality: Chemical Resistant, Water Resistant, Solvent Resistant
• Packaging Size: 1, 5 or 20L
• Usage: Industrial Use
• Brand Name: Humiseal
• Material: Acrylic,PU and Silicon
• Certification: UL,MIL,IPC,GX
• Shelf Life: 2Year
• Color: Clear
• Purity: 100
• Grade Standard: Industrial Grade
• Texture: Soft
• Form: Liquid
• Surface Finishing: Polished
• Country of Origin: India
• Waterproof: Water resistant
• Soluable In Water: No
• Weight Per Litre: 1 kg
• Density: 0.895
• Softening Point: 125
• Melting Point: 200
• Compressive Strength: nil
• Drying Time: 15 min
• Moisture: nil
• Specific Gravity: 0.895
• Viscosity: 200-350 cps
• Acid Value: nil
• Melting Temperature: nil

• Type: Conformal Coating
• Material: Resin
• Certification: ISO 9001:2008 Certified
• Pattern: Plain
• Texture: Hard
• Brand Name: ISC
• Drying Time: 10 Minutes
• Thickness: 25 - 75 Micron
• Application: Electric Board Use
• Feature: Waterproof
• Condition: Liquid
• Application: PCB Protection From Moisture, Dust & Rust
• Solids Content (Aerosol): 12 ± 1
• Solids Content (Liquid): 25 ± 1
• Recommended Coating Thickness: 25 – 75 μm
• Curing Time: 24 Hours @Rt Or 30 Min @ 76°C
• UV Inspection: Yes, Fluoresces Under UV
• Fungus Resistance: Passes
• Temperature Resistance: -65° C To 125° C
• Dielectric Withstand Voltage, per Mil-i-46058c: >1500 Volts
• Dielectric Breakdown Voltage, per Astm D149: 7500 Volts
• Dielectric Constant, at 1MHz and 25°C per ASTM D150-98: 3.6
• Dissipation Factor, at 1MHz and 25°C per ASTM D150-98: 0.03
• Insulation Resistance, per MIL-I-46058C: 8.0 x 1014 ohms (800TΩ)
• Moisture Insulation Resistance, per MIL-I-46058C: 6.0 x 1010 ohms (60GΩ)
• Flammability: Yes, Flammable
• Coverage Area for PCB (10cm X 10 cm) (Aerosol): 0.8 Grams – 0.9 Grams
• Coverage Area (Single Coat) (Aerosol): 7 Grams/Sq. Ft
• Size Available: 400 Ml Aerosol Spray, 1 Lit, 5 Lit, 25 Lit.

• Type: Conformal Coating, Industrial Automation
• Form: Liquid
• Brand Name: ASS
• Application: Industrial Use
• Pack Size: 400 ml, 500 ml

Features of ACC 2010 Acrylic Conformal Coating ACC 2010 Acrylic Conformal Coating is a flexible transparent acrylic coating for the protection of electronic circuitry formulated to meet the highest resistance requirements. Used on printed circuit boards as protective coating against moisture, dust, humidity and fungus. Protects all Electrics/Electronics Circuitry equipments in Extreme Service Environments. Excellent adhesion and dielectric properties. Good moisture resistance & Quick Evapouration.   Application of ACC 2010 Acrylic Conformal Coating It used as extra/after insulation of coils and transformers and reduces operational noise. Military Equipment Aerospace Industry Air Conditioner Circuit Board Industrial Applications Automotive Applications   Direction of ACC 2010 Acrylic Conformal Coating Shake well can before use at least 1 Minutes.Hold the can at least 15 to 20 cm from the surface you are spraying and keep the can upright during use. Protect & Mask areas not Coated. Two light coats is best results better than one heavy coat.Coating becomes dry in 20 minutes. make sure the surface is completely dry before using. completed cure takes place in about 24 hours depends upon the humidity. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes.   Precaution of ACC 2010 Acrylic Conformal Coating Contains gas under pressure do not punctured ,may explode if heated. Extremely flammable aerosol. Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized ontainer: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source. Use only outdoors or in a well-ventilated area. Avoid breathing vapor. Wash hands thoroughly after handling. Causes serious eye irritation. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of ACC 2010 Acrylic Conformal Coating Storage : Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F. Store in a well-ventilated place.keep container tightly closed. Keep Out of Reach of Children

• Transparent: soldarable
• hard: ecofriendly

We are offering conformal coating. "global quality through indigenous technology" coninspune make acrylcoat conformal coating transparent ,sold arable , hard coating to protect printed circuit board assly .from environmental conditions like high humidity , conductive dust , corrosion , rust, fungus etc. The coating is ecofriendly with rohs , c-dot , soltspray , certificationand confirming to mil - 46058c specifications . available in 500 ml spray & 1 ltr lacquer . Normally ex-stock.

We offer conformal coating,plastic coat. Conformal coating, plastic coat #4482 single component acrylic plastic coating, water clear transparency excellent electrical properties high resistance to burning,heat,cold,salt,alkalies.mild acid, will not crack peel-color does not contain any cfc’s or odc’s for industrial use only formulated with high performance acrylic resins,premium grade materials& engineered to offer excellent applications properties.this products provides superior gloss,excellent flow & leveling. Applications: enchances the lifespan of electronic pcb assemblies,seals dials,gauges,instruments,electric control panels,junction boxes. Improves their reliability & protect them from rust & corrosion. Directions for use: clean surface, shake well& build up coating by spraying 3 to 4 thin layer at an interval of 10 to 15 minutes of each coat

Electocoat PCB Acrylic Conformal Circuit Coating, Mould Release Agent

Conformal Coating for PCB, Motorcycle Chain Lubricant Sprays, Aerosols

PCB Coating Spray, Car Clean Spray, Electrical Contact Cleaner Spray

A silicone resin protective coating for applications where temperature or flexability is a concern. Protects printed circuit boards against static discharge, arching, moisture, humidity, corrosion, and thermal shock. Contains a UV indicator for quality control inspection. Easy to repair.

PCB Conformal Coating, High Efficiency Motor, Electric Piston Hydraulic Pump

• Adhesion to: Aluminum, Ceramic, FR4, Metal, Plastic
• Temperature Stable: High, Low
• Dielectric Strength: 425 volts per mil v/mil
• Cure Characteristics: Fast Room Temp Tack-Free Time < 10 min
• Nonvolatile Content: 99.4 %
•  :  

The high purity solvent helps in diluting acrylic conformal coatings to attain correct viscosity which improves application of protective coating even on complex circuitry. The mixture shows enhanced high temperature performance and improved resistance to chemical solvents.It may also be soldered through, allowing easy repairing in a specific area on board without damaging the adjacent circuitry. The cured coating can be easily removed with solvents such as Ultrasolve (ULS).

• Packaging Type: Can
• Packaging Size: 360 ML aerosole Can,1 Litre,5 Litre,20 Litre
• Density: 0.92 g/cm3
• Usage/Application: Industrial
• Recommended Coating Thickness: 25 to 75 microns
• Shelf Life at Room Temperature: 24 months