Container Inspection

• Country of Origin: India
• Certification: Iso 17712
• ISO 17020 Accredited Inspection Body: ISO 17025 Accredited Testing Laboratory

CDG is an ISO 17021 accredited inspection body & ISO 17025 accredited testing laboratory for ISO 17712 standards. We provide accredited ISO 17712 certification services in Mumbai.ISO 17712 is a set of rules which establish procedures for the unification and classification of security seals for fitting on mechanical cargo containers. It defines the types of seals that can be used for this purpose, but also establishes the basic general requirements and tests that seals must pass in order to be certified under this standard. Compliance with these regulations is an essential requirement for security seals to be accepted for domestic and international transport of goods. ISO 17712 is an International Standard which establishes uniform procedures for the classification, acceptance and withdrawal of acceptance of mechanical freight container seals. It provides a single source of information on mechanical seals which are acceptable for securing freight containers in international commerce. The ISO 17712 establishes “uniform procedures for the categorization, acceptance, and withdrawal of mechanical freight container seals. It gives a single source of information on mechanical seals which are acceptable for securing freight containers in international commerce.” Benefits of ISO Pas 17712:2013 Freight Containers • Minimize container tampering and thefts • Enlarge correct collection of taxes and duties • Get better border security • Facilitate trade • Significant enlarge in inspection rate • Speed up logistic procedures • Enlarge safety • Minimize corruption The ISO 17712 establishes “uniform procedures for the classification, acceptance, and withdrawal of mechanical freight container seals. It provides a single source of information on mechanical seals which are acceptable for securing freight containers in international commerce.” The current ISO 17712 standard requires independent confirmation in three areas: 1. Testing to determine a seal’s physical strength (as barriers to entry). ISO 17712 defines three types of classes of seal strength or barrier capacity: “I” for Indicative; “S” for Security; and “H” for High Security. C-TPAT requires the use of “H” class seals. Suppliers must use independent third party test laboratories to validate a seal's classification. Labs must be accredited according to ISO/IEC 17025 (General requirements for the competence of testing and calibration laboratories) to perform testing specific to ISO 17712. 2. Auditing of manufacturer’s security-related business processes. Poor security-related practices can undercut the effectiveness of a high-quality security seal. ISO 17712's Annex A defines over two dozen required practices, such as facility risk assessments and access controls to production and storage areas. Suppliers’ conformance with Annex A should also be demonstrated through an independent certification provider that is accredited to audit compliance with the ISO standards. 3. Seals be designed and constructed with tamper indicative features that generate tell-tale evidence of tampering. Seal manufacturers must be able to demonstrate to, and obtain certification from, an accredited auditor from an independent third-party organization that their high security seals have built-in tamper evidence features. If an independent third-party organization accredited to ISO 17020 verifies conformity, it will provide the manufacturer with a certificate of compliance that documents that the seals submitted for review do reflect tell-tale evidence of tampering generated by attempts to defeat a correctly closed and affixed seal. Considering that most seals are tampered with in order to introduce illegal contraband or to pilferage a container, this is a welcomed improvement for high security seals –particularly those that are U.S. bound and those affixed to C-TPAT containers and trailers.

Ensure compliance and safety with our ISO container inspection service. Our qualified inspectors meticulously examine shipping containers to verify structural integrity, cleanliness, and adherence to ISO standards. Whether you're shipping goods domestically or internationally, our thorough inspection helps prevent delays, damages, and costly risks. We provide detailed reports and recommendations, allowing you to make informed decisions and meet regulatory requirements. Trust us to safeguard your cargo and streamline your logistics process. Contact us now to schedule an ISO container inspection and maintain the highest quality standards for your shipments.

We are involved in bringing forth unmatched Container Inspection Services to the clienst from all across the nation. Our Container Inspection Services includes inspection at vendorâs warehouse or at forwarder's premise. Through our Container Inspection Services, it is checked whether the number of product matches with the requirement or deal with the client. This is done by checking P/O or Container load checklist. Within our Container Inspection Services, we also inspect if the products are in good conditions.

Technical Inspection Why inspect with us?  DCS & LL-C(Europe) has available a global network of qualified inspectors. We prefer experience and qualification of the inspector in combination with regular inspections on the production or assembly sited in the field of large assembly and complex equipment inspections. For inspections of simpler products (check of functionality, quantity and packing), we can offer appropriate prices thanks to the network of inspectors in more than 40 countries of the world. As standard with our quotation, we deliver anonymous curriculum vitae of an inspector for the customer to review his/her experience before placing an order. We are always looking for the most feasible inspection while keeping finances in mind. We always review the costs with respect to full customer costs; we also regard the costs for test samples, transport costs, inspector travelling expenses and last but not least the time factor. When outsourced inspection services are paid off?  Unique assemblies.  Surely always when the supplies of unique products are at stake (investment units, constructions, complex equipment). Hence, in cases when no series production products are involved but supplies where extensive financial loss may be suffered due to any error. For a series-produced product, it is always fine to replace the product, however, for a larger project poor quality sub-supplies may result in extra costs related to repairs, time shifting for delivery of the project as well as financial loss of the customer due to delayed launch of operation.Remote supplier.  We have available a global network and our inspectors within he global network are often closer to the manufacturer than the customer representative. We can offer an inspection from one-day visit to permanent or repeated involvement at the manufacturer.Legislation requirements.  We can arrange inspection services such as functional tests, reviews, measurement or completion of the documents and certificates required from competent bodies should the purchased product subject to legislation requirements of the importer’s country.  Ranges and types of the technical inspection Check of project completeness.  This type of inspection is performed from the draft phase within the inspection of construction or production documentation followed by inspection right during the production, assembly or repairs of technical equipment and the final operation and review tests. For this inspection type, DCS & LL-C(Europe)  usually produces an independent inspection procedure submitted for final approval by the customer. Instrument for declaration of compliance Declaration on conformity of producer, supplier or operator.  For some modules, where declaration on conformity by the producer or supplier is required for checking of compliance (e.g. CE mark), an inspection report from third party is a legitimate document for issuing of the certificate. Use our experience to help the producer, supplier or operator of equipment to find an optimum solution for cooperation from determination of basic requirements, testing up to full inspection services.   Additional Information: Pay Mode Terms: T/T (Bank Transfer),Western Union