Cylindrical Drum Dealers

    CONSTRUCTION Mild SteelTinGalvanized CAPACITY 10 Ltrs – 25 Ltrs COATINGS Epoxy, Lacquer, Varnish, Other Anti – Rust/ Corrosives OPENINGS 4” Lid with Capseal, 1.75” Screw Cap, 2” Bung, Flex Spout APPLICATIONS For the Packing of Coatings, Chemicals, Solvents, Adhesives, Paints, Inks, Resins, Construction Chemicals, Hazardous Solvents.  

Adfit, leading manufacturers & exporters of pipe fittings in India. We supplies various pipe fittings including buttweld seamless pipes and welded pipe fittings, SS 904L Plate, SS 904L Flanges & Branch connections in different sizes, range, type and schedule-class. Adfit regularly supplies its material to core industries such as Sulphuric Acid and phosphoric acid plants, seawater heat exchangers, chemical plants, food processing plants 904L is a high-alloy austenitic stainless steel with low carbon content. The grade is intended for use under severe corrosive conditions. It has been application proved over many years and was originally developed to resist corrosion in dilute sulfuric acid. It is standardized and approved for pressure vessel use in several countries. Structurally, 904 L is fully austenitic and is less sensitive to precipitation ferrite and sigma phases than conventional austenitic grades with high molybdenum content. Characteristically, due to the combination of relatively high contents of chromium, nickel, molybdenum and copper 904L has good resistance to general corrosion, particularly in sulfuric and phosphoric conditions. MachinabilitySlow speeds and positive feeds will minimize this alloy's tendency to work harden and glaze. Use chip breakers where possible to overcome problems with long draggy chips. WeldingMost common fusion and resistance methods may be employed. For maximum corrosion resistance, it is recommended to use filler metals of equal or higher alloy content. Hot WorkingHot work should proceed after uniform heating to 2000-2200 F. Doe not work the material at less than 1800 F. Full annealing should follow any hot work to re attain maximum ductility and corrosion resistance. Cold WorkingAlthough higher forces are required, 904L will respond in a similar fashion to other austenitic stainless steels like 304, 316 or 317. Most common operations can be successfully performed. Annealing1920-1990 F ( 1050-1090 C ), rapid cooling. HardeningThis alloy does not respond to heat treatment.. It may only be hardened by cold reduction. DESIGN FEATURESGood resistance to pitting and crevice corrosion.Very good resistance to stress corrosion cracking.Good resistance to intergranular corrosion.Good formability and weldability.Maximum service temperatures of450 deg.C. (824 deg.F). TYPICAL APPLICATIONS

• Material: Cylindrical Plastic Drums
• Color: Black
• Capacity: >300 litres
• No Of Mouth: 1
• Storage Material: Water

Rotating cylindrical drum complete wflights Bitumen and Bins piping, Sprocket drive W20 H.P. Electrical Motor Frame Mounted Exhaust Fan and drive W20 H.P. Electrical Rotating Cylindrical Drum is fixed at proper angle 150 to avoid unnecessary load on its electrical Motor and give proper heated aggregate to load out belt. Electrical motor is coupled with fluid coupling to protect its AC Motor

• Material: Plastic
• Shape: Cylindrical
• Brand Name: Sintex
• Features: Resistance against rust, Hygienic, Light-weighted
• Capacity: 50-100 litres
• Height: 490-710 mm
• Diameter: 390-445 mm
• Mouth Opening: 280-400 mm

Despite being compact and lightweight, this reel provides a long stroke of up to 4m (winding length). Due to the use of a cylindrical drum, the tension (winding force) increases gradually as the wire rope is pulled out. The cylindrical drum also prevents cable jamming even when you pull out the wire rope in an oblique direction. Balance is obtained at the preset height and the wire rope is wound up after being pulled out again.

mild steel cylindrical drums, mild steel conical drums

Size of Pipe From 50 mm to 150mm Diameter Drive For Corrugator 5HP.3 Phase 415±5 voltage Gear Motor [standard make] Variable Speed Drive 0.5 m/min to 10m/min speed variable depend on size & output of extruder with emergency stop arrangement. Lubrication System Centralized lubrication system used to give specific pulse at specific place to easily slide with low friction. Cooling System Inbuilt cooling channel with brass fitting of inlet & outlet connection for chilled water. Air Chiller Used as additional air cooling for better finish & output Line Speed Per Minute 3 to 6 Meter /min depend on size of pipe.

TECHNICAL SPECIFICATION, photography jacket, Photo Album, Photo Printers

Cylindrical Household Drum, Water Tank, Pipe & Fitting

Mild Steel Drums Cylindrical, Gold Or Pigmented Epoxy Coated Drums

Cylindrical Drum with The Hole In The Lid, White HDPE Jar

Cylindrical Drums, Oil Barrels, automotive stamping

Cylindrical Plastic Drum

Cylindrical Drum, Hdpe 240 Ltr Container, Plastic Chemical Drum

TECHNICAL SPECIFICATION, feature phone, Mobile Phones

Cylindrical Drum, Wedge wire basket, Wedge wire tubes

Plastic Cylindrical Drum, plastic pail, hdpe buckets