DIN Abrasion Tester Dealers

• Brand Name: ALPHA CHEM
• Model Number: ALPHA CHEM-1413

Din Abrasion Machine : Alpha Chem is manufactures,exporter & suppliers Din Abrasion Machine. Din Abrasion Machine : DIN Type Abrasion Tester applies to the abrasion test of resilient material, rubber, tyre, transport belt, synthetic leather. Itâ€Â²s effictive and esay to operate. Specimens size 16mm, 6-15mm (D) Fixture load 2.5N Weight load 2.5N, 5N Fixture lateral displacement 4.2mm/wheel each lap Wheel diameter 150mm Wheel length 460mm Wheel rotate speed 40rpm Travel reservations 40m/20m Abrasion speed 0.32m/sec Dip angle 3& deg; The angle of the specimen Back shaft with vertical roller face Machine Size(L& times; W& times; H)70& times; 30& times; 30cm Weight 61 KG approx. Power : AC220V, 3A

• Dimensions of the Specimen: 16mm diameter with minimum height of 6 mm
• Dimensions of Rotating Drum: 150 mm diameter with x about 460 mm long
• Speed of Rotation of Drum: 40 rpm
• Lateral Movement of Test Specimen Holder: 4.2 mm per revolution of drum
• Rotation of test specimen: 1 revolution per 50 revolutions of drum
• Load on test specimen: 5/10N
• Total length of abrasion run: 40 meters (about 84 revolutions)
• Related standard: ISO: 4649 – 1985 , ASTM D5963, IS: 3400 (Part- III) - 1987

In din method of determine abrasion resistance of vulcanized natural or synthetic, a cylindrical rubber test specimen is abraded against an abrasive surface mounted on a rotating cylindrical drum in such a manner that abrasion takes place on one of the flat ends of the test specimen which is held against the abrasive surface under a specified load while being traversed across it. The ratio of the volume loss of a standard rubber to the volume loss of the test rubber measured under the same conditions, expressed as a percentage, gives the abrasion resistance index of the rubber under test.   The ASIAN Din Abrasion Tester is designed to determine abrasion resistance index of natural and synthetic rubber in accordance with the above principle. It consists of test specimen holder with a cylindrical opening adjustable between 15.5 to 16.3 mm to clamp the test specimen with an arrangement to adjust the length of test specimen protruding out. The holder is mounted by a screw mechanism along a length of a rotating drum on which the abrasive cloth is fixed. The movement to the screw mechanism and drum is given by an electric motor, gearbox and chain mechanism to give the specified speed of rotation to the drum and the specified lateral movement to the test specimen holder. The swivel arm and test specimen holder are so disposed that the test specimen is pressed against the drum under the specified load with its center axis at an inclination of 3 degree to the perpendicular in the direction of rotation and placed above the longitudinal axis of drum. A rack and pinion arrangement to rotate the test specimen about its axis during the test (whenever desired) is also provided.   The abrasive cloth is firmly fixed to the drum using a suitable peel able adhesive with the ends of the abrasive cloth butt jointed together. The equipment is provided with limit switches which, in addition of giving over travel safety to the movement of test holder by preventing the lower edge of the test specimen holder to touch the abrasive cloth.   The equipment is built on rigid steel base and finished in grey metallic and bright chrome / zinc plating to give it a corrosion resistant finish.   Molding die, rotary type cutting die (hollow drill) for preparing test specimens and extra abrasive cloth are available as optional accessories.

• Application: Industrial Use
• Feature: Stable Performance, High Accuracy
• Power: 50 Hz
• Quality: Optimum Quality
• Voltage: 220V

• Country of Origin: India

A DIN Abrasion Tester determines the resistance of Elastomers in regard with the frictional loss on Rubber product such as footwear, tyres, conveyor belts ,hoses ,floor covering etc. As the wear is always the result of abrasion ,hence it simulates long term wear effectively .This tester is designed and manufactured in accordance with DIN standard. It is used for uniformity tests and comparison tests of rubber abrasion. Abrasive paper is wound on the surface of a rotary drum and rubber specimen subjected to load is moved on the abrasive paper. The amount of rubber reduced in the specimen due to the abrasion is measured. PARAMOUNT DIN Abrasion Tester i9™ is Next Generation equipment made exactly as per International standards  The Equipment allows user to measure the abrasion resistance of rubbers (vulcanized thermo-set rubbers and thermoplastic elastomers) that are subject to abrasive/frictional wear in their actual service, such as tires, conveyor drive belts, and shoe soles. The abrasion distance is easily selected by an adjusting screw. The constant pressure on the sample is set by using a variety of loading weights. If the test requires sample to be rotated around its own axis, this rotation is easily activated by the operator.

• Feature: Low Maintainance, High Accuracy, Stable Performance
• Application: Industrial

• Diameter of test specimen: 16 + 0.2 mm
• Height of test specimen: 6 to 10 mm
• Diameter of rotating drum: 150 mm
• Length of rotating drum: 470 mm
• Speed of rotation of cylinder: 40 + 2 RPM
• Lateral movement of test specimen holder: 4.2 mm per revolution of drum
• Load on test specimen: 10 N / 5 N

MYQ Din Abrasion Tester is designed to determine abrasion resistance index of natural and synthetic rubber in accordance with the above principle. It consists of test specimen holder with a cylindrical opening adjustable between 15.5 to 16.3 mm to clamp the test specimen with an arrangement to adjust the length of test specimen protruding out. The holder is mounted by a screw mechanism along a length of a rotating drum on which the abrasive cloth is fixed. The movement of the screw mechanism and drum is given by an electric motor, gearbox and chain mechanism to give the specified speed of rotation to the drum and the specified lateral movement to the test specimen holder. The swivel arm and test specimen holder are so disposed that the test specimen is pressed against the drum under the specified load with its center axis at an inclination of 3 degrees to the perpendicular in the direction of rotation and placed above the longitudinal axis of the drum. A rack and pinion arrangement to rotate the test specimen about its axis during the test (whenever desired) is also provided. The abrasive cloth is firmly fixed to the drum using a suitable peel able adhesive with the ends of the abrasive cloth butt jointed together. The equipment is provided with limit switches which, in addition to giving over travel safety to the movement of test holder by preventing the lower edge of the test specimen holder to touch the abrasive cloth. The equipment is built on the rigid steel base and finished in gray metallic and bright chrome/zinc plating to give it a corrosion resistant finish. The molding dies, rotary type cutting dies (hollow drill) for preparing test specimens and extra abrasive cloth are available as optional accessories.

NAUGRALABS LABORATORY PRODUCT NAME: DIN ABRASION TESTER FOR TESTING LAB NaugraLabs Laboratory Product Code: NLE-Export-380016 Description and Specification for Lab Tenders Din Abrasion Tester For Testing Lab Workshop. Din Abrasion Tester - For Testing Lab We offer high quality Din Abrasion Tester. Technical Specification:- Diameter of test specimen - 16 ± 0.2 mm Height of test specimen - 6 to 10 mm Diameter of rotating drum - 150 mm Length of rotating drum - 470 mm civil lab equipments manufacturers

Din Abrasion Machine : DIN Type Abrasion Tester applies to the abrasion test of resilient material, rubber, tyre, transport belt, synthetic leather. It′s effictive and esay to operate. Specimens size    16mm, 6-15mm (D) Fixture load 2.5N Weight load 2.5N, 5N Fixture lateral displacement 4.2mm/wheel each lap Wheel diameter 150mm Wheel length 460mm Wheel rotate speed 40rpm Travel reservations 40m/20m Abrasion speed 0.32m/sec Dip angle 3& deg; The angle of the specimen Back shaft with vertical roller face  Machine Size(L& times; W& times; H)70& times; 30& times; 30cm Weight  61 KG approx. Power    :  AC220V, 3A

• Material: MS
• Frequency: 50 Hz
• Usage/Application: Laboratory
• Test Specimen Load: 5/10 N
• Rotation Drum Speed: 40 RPM
• Total Length Of Abrasion Run: 40 Meters (About 84 Revolutions)
• Specimen Dimensions: 16 mm Diameter With Minimum Height Of 6 Inch
• Rotating Drum Dimension: 150 Mm Diameter With X About 460 Mm Long
• Rotation Of Test Specimen: 1 Revolution Per 50 Revolutions Of Drum

We are the manufacturer of World Class Testing Equipments.

• Material: Mild Steel
• Brand Name: Asia Vision Instrument
• Frequency: 50-60 Hz
• Rotating Speed: 60 RPM

• Dimension: 95cm x 36cm x 46 cm.
• Holder Moving distance: 4.2 mm each rotation

Din Abrasion Tester helps to determine the abrasion resistance of natural or synthetic rubbers, thermoplastic amorphous polymers and vulcanized thermo-set rubbers that are focused to frictional wear in their definite service like conveyor drive belts, tyres and shoe soles. During the test procedure, the quantity of rubber reduced due to abrasion is measured. The ratio of the loss of standard rubber measures against the loss of test rubber and expressed in terms of percentage to provide abrasion resistance index of the sample put under test. The testing instrument is equipped with a metallic base plate and polished with Autumn Gray and Blue colored combination painting along with intense zinc plating to provide it a corrosion resistant finish.

• Diameter of test specimen: 16 ± 0.2 mm
• Height of test specimen: 6 to 10 mm
• Diameter of rotating drum: 150 mm
• Length of rotating drum: 470 mm
• Speed of rotation of cylinder: 40 ± 2 RPM
• Specimen holder: 4.2 mm per revolution of drum

RELATED STANDARDS IS 3400 (Part 3) ­ 1987 :  Methods of Test for Vulcanised Rubbers  Part 3 :   Abrasion Resistance using a Rotating        Cylindrical Drum Device DIN  53516 :  Testing of Rubber and Elastomers -  Determination of Abrasion Resistance Abrasion Resistance using a Rotating Cylindrical  Drum Device Load on test specimen      :   10 N / 5 N Inclination of axis of specimen holder :  3º from vertical Total length of abrading run :   40 m (about 84 rotations) Abrasive cloth                 :   450 mm wide  x  473 mm long coated With aluminium oxide abrasive     grain of 60 grit Motor                         :   ¼ HP - 230 volts AC   

The GLOBE Rotating Drum Abrasion Tester is designed to determine abrasion resistance index of natural and synthetic rubbers in accordance with the above principle. It consists of test specimen holder with a cylindrical opening adjustable between 15.5 and 16.3 mm to clamp the test specimen, with an arrangement to adjust the length of test specimen protruding out.

We provide you to its world of din abrasion tester

Din Abrasion Tester, Color Matching Cabinet, Toxicity Analyzer

Din Abrasion Tester