Energy Saving Heater Dealers

• Application: Industrial Use
• Brand Name: Elistein
• Material: Ceramic
• Condition: New

Elstein HTS High Temperature Heaters are ceramic infrared panel heaters, which can be used for operating temperatures up to 900 °C and surface ratings up to 64 kW/ m². HTS series heaters are produced using a hollow-casting ceramic process and are filled with thermal insulation material. This improves the radiant power output to the material to be heated. Furthermore, there is a significant reduction in heat dissipated in the wiring space, so that additional insulation of the heating area is usually not required. Compared with IR heaters, which are produced by using full-poured casting processes, HTS heaters have a considerably reduced heating-up time and, depending on the type of application, enable energy savings of up to 25 %. Elstein HTS high temperature heaters are available in four designs and cover the power range from 60 W to 1000 W. Further Information : Standard Design Thermocouple Heater Variants operating voltage 230 V integrated thermocouple type K (NiCr-Ni) special wattages ceramic hollow casting designation T-HTS // T-HTS/1 // T-HTS/2 // T-HTS/4 special voltages leads 85 mm TC leads 100 mm extended leads Elstein standard socket power leads with ring terminals mounting set integrated insulation

Elstein HTS High Temperature Heaters are ceramic infrared panel heaters, which can be used for operating temperatures up to 900 °C and surface ratings up to 64 kW/ m².HTS series heaters are produced using a hollow-casting ceramic process and are filled with thermal insulation material. This improves the radiant power output to the material to be heated.Furthermore, there is a significant reduction in heat dissipated in the wiring space, so that additional insulation of the heating area is usually not required.Consideration The power can be controlled by using thermocouple heaters with TRD temperature controllers, TSE thyristor switching units and other accessories.IR radiation panels can be assembled using REO reflectors, REF construction sets, EBI and EBF construction elements, BSI and BSH panels as well as mounting sheets MBO.The national safety regulations must be complied with for the respective application, for example, the IEC or EN standard 60519-1, Safety in electrical heating installations.Further information and safety instructions are mentioned in the mounting sheet, which is attached to each heater.

Energy Saving band heaters are ideally manufactured to reduce the time taken to heat the barrel and reduce the energy cost, with optimized heating. In addition to the in built 4mm thick heat saving insulation an extra 12mm – 25mm thick flexible insulation is added on the external sheath covered with an additional metal layer. The power saving on these heaters ranges between 25 – 40% depending on the insulation thickness selection. Features Designed as per customer specifications Variety of termination options Available in one or two piece construction Temp upto 400 deg C S.S. braided termination Metal covering Application Injection moulding Blow Moulding Extrusion Pipe and drum heating

Energy Conservation is achieved by using 1" thick Ceramic fiber insulating blanket on the outer surface increasing the overall outer diameter by 2"(Minimum Length Required is 4"). Reducing power consumption upto 30% because of low thermal conductivity of the ceramic fiber insulation, the external surface temperature of the insulation plus ceramic band heater is approximately 80°C while running the inside surface temperature at 300°C. FEATURES Saving Energy Up to 30% Reduce Wattage of Heater More Uniform Heating Less Down time increases Productivity Reduced Preheating time of Machine Heater cost is recover in shorter time Cool working atmosphere for operator Overall Outer diameter increases by 2" (50 mm APPLICATION Injection Molding Machine Blow Molding Machine Extrusion Line  

• Wattage: +5% -10%
• Voltage: 220V AC to 480V AC
• Resistance: + 10% -5%
• Maximum Watt Density: 8 watts / sq. cm.
• Maximum Temp.: 800° C
• Overall Thickness: 40 mm
• Minimum Dia.: 90 mm
• Minimum Width: 75 mm
• Width – Normal: multiple of 15 + 6mm
• Std. gap between edges: 5 to 10 mm

The Energy Saving Band Heater comprises of two layers of asbestos to reduce the heat loss and save energy up to 25%. Our Energy Saving Band Heater is durable and offers uniform heating without any hassle. The Energy Saving Band Heater is provided with imported nickel chromium resistance wire with Mica, which helps in bearing high temperature. Why Our Energy Saving Band Heater? Sturdy design and high quality Reduces heat loss and save up to 25% energyCan withstand higher temperatureHigh performance

SG Consists of the standard Components plus on additional thermal insulation cover all of which is contained in a single flexible sheath ,this additional thermal insulation cover. reduces energy consumption and temperature controllers while have more "off" cycles and maintained set temperature in comparison to all other non- additional thermal insulation cover heaters. Reduces the rate of heat radiations. Save Energy consumpation upto 30% Fully flexible in-spite -of additional thermal insulation cover and heavy wall thickness.

• Type: Energy Saving Heater
• Shape: Round
• Voltage: 230V
• Wattage: Up To 3000W
• Warranty: 2years
• Light Source: Electric
• Country of Origin: India

Energy Conservation is achieved by using 1" thick Ceramic fiber insulating blanket on the outer surface increasing the overall outer diameter by 2"(Minimum Length Required is 4"). Reducing power consumption upto 30% because of low thermal conductivity of the ceramic fiber insulation, the external surface temperature of the insulation plus ceramic band heater is approximately 80°C while running the inside surface temperature at 300°C. FEATURES Saving Energy Up to 30% Reduce Wattage of Heater More Uniform Heating Less Down time increases Productivity Reduced Preheating time of Machine Heater cost is recover in shorter time Cool working atmosphere for operator Overall Outer diameter increases by 2" (50 mm APPLICATION Injection Molding Machine Blow Molding Machine Extrusion Line  

• Voltage: 280 -480V
• Shape: Round
• Power: 1500 - 10000 W
• Inner Material: Mica
• Frequency: 50/60 Hz
• Outer Material: Stainless Steel
• Diameter: 125 mm

Vinman's Ceramic Band Heaters are designed and manufactured with more than 25 years of practical experience, for superior performance and life expectancy. As a manufacturer specialized in industrial electric heating elements & the desire to provide quality products and services to our customers both OEM's & End Users, Vinman specializes in designing Ceramic Band Heaters , Mica Band Heaters, Nozzle Heaters & Strip Heaters to your exact specifications. Depending upon applications Vinman's Ceramic Band Heaters are manufactured with high temperature oxidation metal sheath and high grade steatite insulators to withstand high temperatures. A superior grade NiCr resistance wire coil provides uniform and reliable heat distribution with the best combination of physical strength, high emissivity & good thermal conductivity to heat cylindrical parts, good for sheath temperature up to 5000C. Ceramic Band Heaters are also available with various construction styles with special inbuilt Energy saving options. Features: 1. Available in Chrome Nickel Steel with Power Saving Options. 2. Special High Grade Steatite Insulators for Superior Thermal Conductivity. 3. Power saving up to 30%. 4. Designed for Higher Temperature up to 500°C. 5. Robust Terminal Junction with Specially Designed Protection Cap. 6. Efficient Heat Transfer even on irregular surfaces in comparison to Mica Band. 7. Conserves Energy with Improved Heating Efficiency up to 55 Watts per square inch. 8. Engineered for Longer life with Superior quality Nichrome wire for Uniform Temperature & Maximum Amperage carrying capacity. 9. Reduces Down time for replacements. 10. Easy installation and removal. 11. Available in various Lead Terminations & Clampings expandable to fit around the Barrel O.D. Applications: 1. Injection Moulding. 2. Film extruders. 3. Blow Moulding. 4. Plastic & Rubber Processing Machinery. 5. Laboratory Equipment 3 Construction Styles: 1. Premium-Heat Construction 2. Power Saver Construction 3. Power Saver PLUS Construction Electrical Variations: Single Phase: Vinman's band heaters are usually designed on 230 Volts single phase unless specified. Dual Phase: Ceramic Band Heaters can be designed with multiple circuits to operate in single or three-phase circuits. Three Phase: On very high wattage band heaters it would be advantageous to install three-phase wiring to reduce the current load across a single conductor. Three-Phase wiring is available with all types of insulation, Construction styles, and clamping variations. Limitations: Minimum width: 3"(76.2mm).

energy saving heater, Mica Heaters, Thermocouple, Finned Tubular Heaters

Energy Saving Band Heater, Thermocouple Sensors, split type cartridge heaters

energy saving heater, quartz infrared heater, thermal oil heaters

energy saving band heaters, Cartridge Heaters, Titanium Heaters, Thermostats

Energy Saving Ceramic Band Heater, Mica Band Heater, Ceramic Band Heater

energy saving heater, Industrial Heater