Flame Photometer Dealers

• Power: 230 V ±10 % AC, 50 Hz
• Sensitivity: General Mode : Na : 0.5 ppm , K : 0.5 ppm , Li: 0.5 ppm, Ca:15 ppm
• Filters: Na & K Supplied (Ca & Li optional at extra cost)
• Resolution: 0.1 ppm / meq
• Reproducibility: ± 2% FS & ± 2 Digits
• Curve Fit Accuracy: ± 2 % FS
• Display: 20x4 Alphanumeric backlit LCD display
• Average Time: In-built in Software
• Flame System: LPG & dry oil free air
• Detector: Silicon Photodiode
• Calibration: Up to 5-Point Calibration with curve
• Gas Control: Adjustable with knobs
• Ignition System: Auto Ignition
• Atomiser: Axial
• RS-232 Interface: Available (PC Software at extra cost)

Microprocessor Flame Photometers – 1385  comes with Flame Failure detection and   Auto Gas Cutoff Facility. In case of power failure, the gas cuts off automatically. In case the flame goes off accidently during work, the flame failure alarm sounds after a few seconds.   Both Microprocessor Flamephotometers Model 1385 & Model 1382 are used for the determination of Sodium, Potassium, Calcium, Lithium & Barium. They uses the latest microcontroller technology and advanced engineering techniques so as to give enhanced accuracy and reproducibility. They have  soft touch membrane keys for ease of operation. The solution is aspirated through an atomizer. Air, sample and the fuel are mixed in the mixing chamber which is then sprayed as a very fine mist into the    flame. Radiations from the flame passes through a specific narrow band interference filter and pass to the photo-detector. The final results are displayed on the 20 x 4 alphanumeric LCD. The standard model comes with 2 filters (Na & K). Additional filters Ca & Li are optional at extra cost.   In both the models, Calibration can be done with up to 25 standards of user choice(5 point for each element) and non-linearity correction is provided through an automatic curve fitting software. Multiple Calibration Curves  can be stored in the memory. Facility has been provided for re-standardization with a single standard, thereby, eliminating the need of multiple standards once a calibration has been performed.   Features Microprocessor Based with Printer Interface Auto Gas Cutoff (Model – 1385) Auto Flame Failure Detection (Model – 1385) Four Measurements in Single Aspiration Setup Storage Facility Sample Data Storage Facility Curve Calibration Programmability Using Maximum of 25 Standards Multiple Calibration Curve Saving Facility Data Processing Through Curve Fitting Techniques, Least Square, Quadratic Online Help Key Direct Results in ppm and meq Useful for Medical & Soil Testings

• Country of Origin: India
• Size: Multisizes
• Brand: ELICO
• Mobility: Portable
• Measuremet Range: 0 - 100 ppm
• Model Name/Number: CL- 378

• Type: Microprocessors
• Operating Temperature: 0-30 Deg C
• Frequency: 50Hz
• Current Type: AC, DC
• Functionality: Micro Controller
• Pick Up Accuracy: +/-12.5 %
• Auxiliary Power Supply: 85-270V

• Brand Name: Labtronics
• Driven Type: Electric
• Automatic Grade: Automatic
• Application: Laboratory Use
• Voltage: 230 V
• Type: Flame Photometer
• Warranty: 1 Year
• Country of Origin: India
• Mobility: Bench Top
• Measuremet Range: 100ppm
• Sensitivity: +-1 ppm
• Accuracy: +-2 % upto 40 ppm
• Material: MS
• Lamp Type: Tungsten Halogen Lamp
• Size: L355 x B25 x H210 mm
• Warmup Time: 10 Min

• Driven Type: Electric
• Automatic Grade: Automatic
• Application: Laboratory Use
• Certification: CE Certified
• Voltage: 220V
• Warranty: 1 Year
• Country of Origin: India

• Model No: SI-203
• Range  : 0-100 ppm, K : 0-100 ppm, Ca : 15-100 ppm (Optional) Li : 10-100 ppm (Optional) 
• Sensitivity  : Na : 5 ppm, K : 5 ppm, Ca: 10 ppm (Optional),Li: 10 ppm (Optional)  READOUT 2½ Digit Bright Red LE
• Accuracy  : ± 2 % up to 40 ppm ± 5 % above 40 ppm
• Ignition System: With external igniter
• Measurement System  : Measures One element at a time
• Repetability  : ± 2 Counts
• Detector  : Silicon Photodiode
• Filters  : Narrow band interference glass filters
• Nebulizer  : Black bakelite, axial  flow type
• Flame System  : LPG and dry oil free air  
• Warm Up Time  : 10 Minutes  
• Power  : 230 V± 10%,50HZ
• Dimensions  : 355W X 255H X 225mm (Approx.)  
• Weight  : 5 Kg. (Approx.)

• Brand Name: Genist International
• Model Number: GI-141

Microprocessor Based with Printer Interface Auto Flame Failure Detection, Sample Data Storage Facility Four Measurements in Single Aspiration, Setup Storage Facility Curve Calibration Programmability Using Maximum of 5 Standards, Multiple Calibration Curve Saving Facility Data Processing Through Curve Fitting Techniques, Least Square, Quadratic, Direct Results in ppm and meq, Useful for Medical & Soil Testing   Product description The sample solution is aspirated through an automiser. Sample, Air and the fuel are mixed in the mixing chamber which is then sprayed as a very fine mist into the flame. The color of the flame is changed depending upon the concentration of elements present. Radiations from the flame passes through the sensing system and specific narrow band interference filter which permits only the characteristic radiation to pass to the photo-detector. The output of the photo-detector is then processed by the microcontroller and the final results are displayed on graphical lcd display. In both models 5-Point calibration facility and non-linearity correction is provided through an automatic curve fitting software. Microprocessor Based with Printer Interface Auto Gas Cutoff Auto Flame Failure Detection Four Measurements in Single Aspiration Setup Storage Facility Sample Data Storage Facility Curve Calibration Programmability Using Maximum of 5 Standards Multiple Calibration Curve Saving Facility Data Processing Through Curve Fitting Techniques, Least Square, Quadratic Online Help Key Direct Results in ppm and meq Useful for Medical & Soil Testing Mode: General, Serum, Urine Sensitivity: General: Na: 0.5 ppm, K: 0.5 ppm, Li: 0.5 ppm, Ca: 15 ppm Filters: Na & K supplied (Ca & Li are optional at extra cost) Resolution: 0.1 ppm/meq Reproducibility: < 1% coefficient of variation for 20 consecutive samples using 10 ppm Na set as max standard Curve Fit Accuracy: < 2% error when 3 ppm Na/K and 5 ppm Li are set as maximum standards Display: 128 x 64 Graphical LCD Display Flame System: LPG and dry oil free air Detector: Silicon photodiode Calibration: Upto 5-Point calibration with curve fitting software Flame Failure:Auto detection.

• Accuracy: +/-2% upto 100meq/40ppm +/-5% above 100meq / 40ppm
• Read out: Dual 2.5 Digit Red LED
• Ignition: In built ignition by pressing knob
• Measurement System: Simultaneous measurement of 2 elements on dual display
• Repeatability: +/- 2 counts
• Detector: Silicon Photodiode
• Power Supply: 230VAC, 50Hz
• Filters: Na & K incl, Ca & Li at Extra Cost

• Brand Name: GREEN AGRITECH

Max Electronics India is an established manufacturer, supplier and exporter of sophisticated Flame Photometer from India. The Flame Photometers offered by the company are high on quality, performance and are made of the finest quality raw materials, making them durable and long lasting. Flame-photometers are used for determination of Sodium, Potassium, Lithium and Calcium in […] Digital Flame Photometer with 2 filters , Na & K Filters , Auto Ignition . 3 digit LED display along with compressor and other accessories No. of Filters Na & K ( Ca & Li optional ) Range Na: 0 to 100 ppm Ca: 20 to 100 ppm K: 0 to 100 ppm 

• Application: Laboratory
• Feature: Accuracy
• Voltage: 220V
• Country of Origin: India
• Display: Digital
• Brand: Dricon
• Material: Metal

• Type: Automatic
• Certification: CE Certified
• Application: Laboratory Use
• Voltage: 220V
• Driven Type: Electric
• Warranty: 1 Year
• Finish: Polished
• Brand Name: Equiptronic

FLAME PHOTOMETER DIGITAL with Na & K Filters Compressor included.  Auto Ignition  

• Material: Stainless Steel
• Color: White
• Automatic Grade: Automatic
• Application: Industrial, Residential
• Feature: Accuracy, Digital Water Meter Display
• Type: Digital Flamephoto Meter

SIS – 1379    RANGENa:0-100ppm K:0-100ppm SANSITIVITYSodium (Na) : 5ppm Potassium (K) : 5 ppm ACCURACY±2% up to 40 ppm ±5% above 40 ppm  

• Type: Flame Photometer
• Application: Laboratory Use
• Automatic Grade: Automatic
• Driven Type: Electric
• Country of Origin: India
• Brand Name: VSI

VSI Electronics Private Limited is an established manufacturer, supplier and exporter of Digital Flame Photometers from India. The Digital Flame Photometers offered by the company are high on quality, performance and are made of the finest quality raw materials, making them durable and long lasting. These Digital Flame Photometers are used for determination of Sodium, Potassium, Lithium and Calcium in blood and soil samples.   Various types of Flame photometers such as Microprocessor Based, Digital Flame Photometers & Digital Clinical Flame Photometers are available. The most advanced technology is used to manufacture these Flame Photometers. Advanced features like PC connectivity through RS232 serial port connection to the computers is also available. The simultaneous measurement of two or four elements is available with single aspiration of sample.   VSI Electronics Private Limited is one of the most reputed Flame Photometer Exporters in the market. A wide choice of flame photometers is available to be used in the medical clinical labs, soil testing labs, milk plants etc.   Models Available: VSI-FP1, VSI-FP2, VSI-603, VSI-604 and VSI-605   Microprocessor Flame Photometer (VSI-603) with two Filters - Sodium (Na) & Potassium (K).  Two Elements measurement in a single aspiration.  It has 5-Point Calibration, Direct Readout in ppm & meq/l, Auto Filter Selection, Auto Ignition, Graphical LCD Display, Two Element measurement in a Single Aspiration, Auto Gas Cut Off facility, RS 232 Interface PC Software, printer attachment facility with compressor and other accessories for lab & medical use.    Microprocessor Flame Photometer (VSI-604) with four Filters - Sodium (Na), Potassium (K), Calcium (Ca) & Lithium (Li).  Four Elements measurement in a single aspiration. Calibration curve fit routines first order and second order. Data displayed in concentration units i.e. ppm & meq, automatic filter selection; auto calibration feature. Printer attachment, PC connecting compatibility, Sample data storage more than 500 results. Alphanumerical key board for easy data entry. Auto Ignition, Graphical LCD Display thus easy to read, Curve calibration using up to 5 standard, multiple calibration curve saving facility, Stainless steel burner. Auto Gas Cut-Off facility in case of power failure. Provided with Four Filters, Compressor and other accessories for lab & medical use.    SALIENT FEATURES : Direct Results in ppm and meq Auto Ignition Facility       Auto Gas Cutoff Facility Auto Flame Failure Detection Setup Data Storage Facility Sample Data Storage Facility Four Measurements in Single Aspiration (In Model VSI-604) Curve Calibration Programmability Using Maximum of 5 Standards Multiple Calibration Curve Saving Facility Data Processing Through Curve Fitting Techniques, Least Square, Quadratic Re-standardization with One Standard Online Help Key Batch-Wise, Date-Wise and Individual Result Data Printing RS232 Interface to download data to PC Useful for Medical & Soil Testing   Note: Appearance & Specifications are subject to change due to continuous development.