Gas Separators Dealers

• Efficient: Cost-effective

Fenix supplies a large variety of separator internals FXIntSep used in the Oil & Gas industry. Many of these have uses in other industry applications, but some have been developed specially for areas in processing of natural gas and petro-crude such As: • Oilfield production (gasoilwater) • Separators (onshore, offshore and F.P.S.O.) • Test separators • Free Water KO drums • Oilwater coalescers • Compressor scrubbers • Gasliquid KO drums & inlet scrubbers Fenix offers a range of design services to support your front-end engineering including process simulations, internals selection and vessel sizing and optimisation. In addition we offer computer aided drafting and 3-D plant layout design. We continually review our technologies and employ new approaches whenever demanded to improve quality and flexibility. Because process simulation, design and manufacture are carried out in-house, chance of any error or slip is minimized. Our specialization in using AspenPlus is employed in solving the typical challenges encountered by clients in their operations. and assist us to design superior new plants and retrofit existing plants for higher productivity. Equipments we design and manufacture in this category are : Inlet distributor Perforated baffle plates Straightening foam breaker vanes Foam breaker matrix Coalescers Plate packs Matrix packs Dual media coalescers Wiremesh demisters Vane mist eliminators Sand jet spray systems etc.

• SIZES: From 2"NB to 36"NB

Extremely efficient separation of entrained liquids & mists from Gas or vapor flow.100 % removal of liquid particles 8 micron and larger. Low pressure drop.PURIC Vane Separator consist of a set of specially designed corrugated profile blades, vanes within a receiver. Vanes have hook pockets for uninterrupted liquid collection and drainage. These vanes having series of short radius turns within close proximity utilize Inertlal forces to trap heavier liquid droplets.

• Type: Automatic
• Voltage: 220V/380V
• Condition: New
• Warranty: 1 Year
• After-Sales Service Provided: Spare Parts
• Pressure Rating: 6 — 16 Kg/cm2 or Higher as per Client Requirement
• Gas Handling Capacity: 5000 to 5 Lakh Scmd
• Liquid: 50 Bbls to 2400 Bbls/day
• Standard: Api 12 J

Separators are primarily used for They are used for separating well fluids produced from oil and gas wells into gaseous and liquid components.

• MOC: SS 316, SS 304, CS, CS
• Manufacturing Std:: ASME, IS, CEN, BiS, API & Other

Our gas and oil separators have proven themselves in service. Available in a range of custom sizes and configurations, they offer cost-effective solutions for greater well production. Three Phase separator-ChemsepTManufactured to ASME & API requirements, our vertical and horizontal separators are used for gas, water, sand and oil separation.

Charam Techno Chemical & Equipments (P) Ltd. is a trusted name among the major High Performance Lead Gas Liquid Separator Exporters in India as our Separators have most effective separation by our design.

• Country of Origin: Made in India
• Max Press: 30 Bar
• Application: Liquid & Fine Particulate Removal
• Max Temp: 150 C

  Gas (Vapour) Liquid Seperator (Knockout Seperator)   Knockout Separator is basically a vapor Liquid Separator, designed mainly on Hydrocyclone principle. It is constructed similar to Hydrocyclone with a Liquid collected at the Bottom. The outlet at where vapor goes upwards may be connected to suction of a blower or to a vacuum.  

UNIQUE Mud/Gas Separators are designed for use where drilling is likely to encounter large volumes of gas. Unique Mud/Gas separators are designed in accordance with ASME Sec VIII Div.1 and NACE standards. The Unique design is especially advantageous in sour gas environments or when drilling with an underbalanced mud column. The Mud Gas/Separator is used primarily to separate and safely vent large pockets of free gas from the active mud system.

The company is considered as a renowned manufacturers and exporters of Gas Separator who offer you an extensive range at very lowest prices. These are being fabricated by our well qualified team of experts. We have got a lot of appreciation because of its high quality with perfection to finish. It can also be customized as per the stated specification of our valued customers. We are amongst the highly considerable manufacturing company who provides an assortment of qualitative Gas Separator. Our organization is among the well reckoned Gas Separator manufacturers and suppliers that can provide superb quality products. Our business entity is one of the most preferred Gas Separator manufacturer and supplier that is widely appreciated and acknowledged due to its high quality at reasonable prices.

Gas Cyclone Technical Description One area of application of gas cyclones is the pre-filtration of solids from gases. Gas cyclones have no moving parts, and so are low-maintenance systems. They can also be used in conjunction with high gas temperatures. For these reasons they are in widespread use. This trainer was developed in cooperation with the Institute for Solids Process Engineering and Particle Technology at TU Hamburg-Harburg. A disperser is used to disperse the feed material (quartz powder recommended) finely in an airflow. The airflow laden with solid material (raw gas) in this way is fed tangentially into the cyclone at the top. In the cyclone, the airflow moves downwards as a rotating primary vortex. At the bottom of the cyclone the vortex is reversed. In the middle of the cyclone it moves as a secondary vortex back up towards the immersion tube, where the cleaned gas emerges from the cyclone. The main separation process takes place in the primary vortex. Owing to the centrifugal forces and the difference in density between the air and the solid, the coarse solid particles move towards the wall. They slide down the wall and are collected in a tank at the bottom of the cyclone. No complete separation of the entire solid material takes place. The fine particles which are smaller than the separation size are ideally discharged from the immersion tube at the top with the secondary vortex. This fine material is separated out of the air flow by a filter. The separation size defines the theoretical boundary between the fine and coarse material. The solid content of the raw gas can be adjusted by means of the disperser and an airflow control valve. To prevent loading of the airflow with particles upstream of the disperser, the drawn-in room air is filtered. An air suction fan generates the airflow. Pressure measurement points at the relevant positions in the trainer enable to determine the pressure loss. For particle size analyses of the feed and the coarse material, a balance and a screening machine are recommended.

• Series: 338,400,513,538,562,675,862
• Size: 3.38″-8.62″

There are stages under 338/387/400/540/675 and other series that produced in our factory. There are bearings, sleeves, volsters, gas separators and other serial parts for ESP. Customized products under our partners requirements could be made also.

Compressor, hydraulic & air, lube oil & gas seperators and filters we are manufacturing replacement element line with an active program of research and development. In this way we can ensure high quality standard of our elements. gas turbine air intake filters easy to install & clean high efficiency higher filtration area conical and cylindrical design we can also retrofit to various models as per requirement. compressor filter air filter oil filter air oil separator we can also retrofit to various models as per customer requirement ( atlas copco,ir, kirlosker etc ) hydraulic & lube oil and air filtration elements suction line filter pressure line filter return line filter duplex filter spin-on cartridge air breather filter

• Brand Name: Trans Power
• Material: Mild Steel and also available in Stainless Steel
• Voltage: 220 V and also available in 440 V
• Phase: Single and also available in Three
• Frequency: 50 Hz
• Power Source: Electric
• Current Type: AC
• Automation: Automatic and also available in Semi Automatic  

Three Phase Separator is a vessel designed to separate the gas that flashes from the liquid as well as separate the oil and water. 3 Phase separator is used when there is large amount of gas to be separaed from the liquid and the dimensions of the vessel are determined by the gas capacity.Three phase test separator is used to mechanically separate hydrocarbon stream the liquid and gas components that exist at specific temperature and pressure.Three phase separator design is important because separator is normally the intial processing vessel in any well testing and Early production facility. Improper design of Three phase separatorcan be a bottleneck and reduce the capacity of the entire well testing or Early production process facility. Downstream equipment's of Three phase separator cannot handle high proportion of gas- liquid mixtures. Generally three phase test separator or Production separator are designed to meet performance requirement of below 1% basic sediment and water content. Gas and liquid separators are classified as Three phase separator, Two phase separator, Free knock out drums, Flare KO drum, Production separator, degassers, this can be either Horizontal or Vertical. Increase in performance of three phase separator is achieved by steady state equilibirium condition. Steady state conditions are achieved in three phase separator, two phase separator, production separator by proper control systems on the skid mounted packages. In well testing industry, below standard three phase test separators are commonly used.   42 “ x 10 ft 1440 PSI Test Separator   42 “ x 15 ft 1440 PSI Test Separator   48” x 10 ft 2160 PSI Test Separator   Custom built Three phase separator also available upon request Three phase separator design is basically based upon fluid flow rate , temperature , pressure and fluid properties. Test separators are designed considering 1 min retention time. Where as in early production or production facility the retention time will be based upon crude oil properties which is varying from 3 mins to 30 minutes. VERPL(Vi Energ resources private limited ) three phase separators are packaged in modular skids with pipings and control systems. Skid can be either CSC certified or DNV Certified. Major Factors effecting Three phase separator design are Gas /liquid flowrates, operating & design consitions, surging or slugging tendency, physical properties, presence of impurities, foaming tendencies, corrosive tendencies, etc. Three phase test separator consist of four sections Inlet diverter section, liquid collection section, Gravity settling section and Mist extractor section. Our skid mounted Three phase test separator packages are assembled with liquid dump valve regulated by level controller to maintain steady state liquid level and steady state pressure of three phase separator is controlled by pressure controller with pressure control valve. Which directly impact in performance of the separator. We choose proper internals based upon fluid properties and client requirements to optimize three phase separator design.

Gas Separators, Air Header, Heat Exchanger, industrial sample cooler

gas separator, Gas Generator

Gas Separators, Pp Filter Press, Semi Automatic Filter Press

oil gas separator, Engineering Services, oil bath indirect heater

oil gas separator, multi function calibrator, Test Benches Furniture

Gas Separators, Air Filters, Moisture Separators, Oil Separators

Vertical Gas Separators, Gas Conditioning System, Air Filters, Silencers

Gas Separator and Filter, Resin Bonded Filter Cartridge, Indicator Tapes

Oil & Gas Separator, Needle bearing, Drill Collar, Workover Rig

Gas Separators, Transfer Presses - Straight Sided Presses

Gas Test Separator, Valve Reconditioning Service

Gas Liquid Separators From Eaton, Fuel Vapor Valves

gas separator, Gas And LPG Metering Skid, Bulk Air Eliminator

Mud Gas Separator, Steam Heat Exchanger, blending tank