Horizontal Air Receiver Dealers

• Tank Orientation: Horizontal
• Brand: APE
• Country of Origin: India
• Storage Capacity: 1000 L
• Material: MS
• Pressure Rating: 16 Bar
• Usage/Application: Industrial
• Storage Material: Air

Sudarshan engineering manufactures horizontal & vertical air receivers for compressed air storage. range of the air receivers are as under. sudarshan engineering provides test certificate radiography certificate of air receivers if required.

Horizontal Air Receivers Range from 70 liters to 1,000 liters, internal red oxide applied of every tank for the purpose of reduces moisture. Low pressure Horizontal Air receiver working pressure 9 and 12 kg and High Pressure Horizontal Air receiver working pressure 24 and 30 kg for these tanks are manufactured as a standard compressor model, if any special type also we provide for various applications.

• Country of Origin: Made in India
• Tank Orientation: Horizontal
• Storage Capacity: 500-1000 L
• Material: MS
• Pressure Rating: 150-200 psi
• Material of Construction: MS
• Finish: Paint Coated

Alpha Engineering offers a full range of both horizontal and vertical air receivers upto 5000 its @ maximum working pressure of 30 kgf/cm².These receivers are manufactured according to IS : 2825/ ASME Sec VIII DivI/EN 286 standards.To Store the Compressed Air Depends on the application, Receiver tanks can be designed as per the standard 0.05 m³ upto 5 m³ capacities and the operating pressure upto 40 bar.

The offered range of Horizontal Air Receivers is praised throughout the country owing to their high efficiency, durability and assured reliability. Available at economical prices, these products are in compliance with international quality standards. The detailed technical specifications of these products are tabulated below

In addition, the air consumption vary due to the process supported. In shorter periods the demand for compressed air may even exceed the maximum capacity of the compressor. In fact, it is common in well designed systems not to design the compressor for the maximum peek loads. Air receivers in compressed air systems serves the important purposes of  Equalizing the pressure variation from the start/stop and modulating sequence of the compressor. Storage of air volume equalizing the variation in consumption and demand from the system. In addition the receiver serve the purpose of: :::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::  Collecting condensate and water in the air after the compressor. Sizing the Air Receiver :::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::  The variation in the consumption demand.  The compressor size and the modulation strategy. In general it is possible to calculate the maximum consumption in the system by summarizing the demand of each consumer. The summarized consumption must be multiplied with a  Usage factor ranging 0.1 - 1 depending on the system. In practice it is common that the manufacturer use standardized receivers for specific compressor models based on their know-how.For calculating the receiver, note that it is necessary with a pressure band for the receiver to be effective. If the consumption process requires 100 psig and the compressor is set to 100 psig, there is no storage and no buffer. Any increased demand makes a pressure drop below 100 psig until the compressor controls respond by increasing the volume compressed.If the compressors operates at 110 psig the difference between 110 psig and 100 psig accounts for the air stored in the receiver. If the demand increase, the pressure can drop 10 psig before the minimum requirement is met. Pressure and flow controllers can be used after the receiver for stabilizing downstream pressure to 100 psig and flattening demand peaks. Note that in a compressed air system the pipe work also makes the purpose of a buffered volume.The receiver volume may be calculated with the formulat = V (p1 - p2) / C pa (1)whereV = volume of the receiver tank (cu ft)t = time for the receiver to go from upper to lower pressure limits (min)C = free air needed (scfm)pa= atmosphere pressure (14.7 psia)p1 = maximum tank pressure (psia)p2 = minimum tank pressure (psia)It is also common to size receivers.    To 1 gallon for each ACFM (Actual Cubic Feet per Minute), or  4 gallons per compressor hp (horse power)    1 ft3 = 0.02832 m3  1 inch = 25.4 mm  1 psig = 6.9 kPa = 0.069 bar  1 Gallon (U.S.) = 3.785x10-3 m3 = 3.785 dm3 (liter) = 231 in3 

Backed by rich industry experience, we are manufacturing and supplying a vast range of Horizontal Air Receivers. that are highly recommended in the industry. these receivers are widely known for its durability, easy maintenance and reliable operation. Utilizing the laid pipelines, this range of industrial air receivers is displaced to different sections of the factory and available with us at reasonable rates.

We are offering horizontal air receivers at very market leading prices company.

Horizontal Air Receivers, Refrigerated Compressed Air Dryer

Horizontal Air Receivers, Jaggery Plant, Milk powder plant

Horizontal Air Receiver, Used Air Dryer, Air Compressor Tank

Horizontal Air Receivers, Monel Alloys

Horizontal Air Receiver, Vertical Air Receiver, Brass Drain valve

Horizontal Air Receivers, Agitated Thin Film Dryer, Evaporation Equipment

Horizontal Air Receiver, High Pressure Refrigerated Air Dryers

Horizontal Air Receiver, Air Dryer for Industrial Process

Horizontal Air Receiver, helical bevel gear, clean room installation services