Journal Bearing Apparatus Dealers

• Phase: Single Phase
• Material: Mild Steel
• Automatic Grade: Semi-Automatic
• Frequency Rate: 50 Hz
• Operating Voltage: 230 Volt

• nometer Panel: 18 tubes mounted on a wooden back board

The apparatus consists of a plain steel shaft encased in a bearing and directly driven by a small electric motor. The bearing is freely supported on the shaft and sealed at the motor end. The bearing contains twelve equispaced pressure tapping around its circumference and four additional ones along its topside and on a vertical radial plane. All are connected by light and flexible plastic tubes to the rear manometer panel so that pressure head of a oil at all sixteen points can be clearly observed at all times.The bearings can be loaded by attaching various weights to the arms supported beneath it. A label is conveniently provided at the front of the apparatus.

The apparatus consists of a plain shaft encased in a bearing and directly driven by a small motor. The bearing is freely supported on the shaft and sealed at motor end. The motor speed is precisely controlled by control unit. The bearing contains twelve equispaced pressure tapings around circumference and four along the axis. All tapings are connected by light flexible plastic tubes to the manometer so that the pressure head of all sixteen points can be observed at a time. The bearing can be loaded by attaching weights to the arm supported beneath it. Specifications - Journal 50 mm dia. (Nominal) Bearing 55 mm dia. Weights 4 Adustable weights. Motor D.C.Motor Control Panel for speed control Manometer Board ( Sixteen Tube) Oil recommended - SAE 30/40

• Floor space: 1.5m X 1.5m X 4m Height.
• Journal: 50mm dia.(Nominal)
• Bearing: 55mm dia.
• Weights: 1 Adjustable weights.
• Motor: D.C.Motor.

The apparatus consists of a plain shaft encased in a bearing and directly driven by a small motor. The bearing is freely supported on the shaft and sealed at motor end. The motor speed is precisely controlled by control unit. The bearing contains twelve equispaced pressure tappings around circumference and four along the axis. All tappings are connected by light flexible plastic tubes to the manometer so that the pressure head of all sixteen points can be observed at a time. The bearing can be loaded be attaching weights to the arm supported beneath it. Experiments : Observation of the pressure profile at various conditions of load and speed. Plotting the cartesian and polor pressure curves. Plotting the theoretical Sommerfield curves. Service Required : A.C,Single Phase .230 V. stabilized power supply. Control Panel for speed control. Manometer Board(Sixteen Tube) Oil recommended - SAE 30/40.  

• MODEL NO: KCTOM-106

The apparatus consists of a plain steel shaft excavated in a bearing and directly driven by a FHP Motor. The bearing is freely supported on the shaft and sealed at the motor end. The speed of the motor is controlled by the speed control unit. One compound pressure gauge is mounted on Bearing to measure the pressure at different position around the circumference. Bearing is free to rotate and can be adjusted at any position of circular scale. The bearing can be loaded by attaching weights to the arm supported beneath i

Journal Bearing Apparatus available was with oil manometers which possessed so many problems, mainly air bubbles, overflow of oil, due to which full pressure could not be developed. Also bearing having very large radial clearance presented question about application of theory itself. Hence, we developed a journal bearing apparatus with a practical radial clearance of 0.2 mm and with a pressure gauge. Clearance of 0.2 mm eliminated question about application of theory and use of rotatable pressure gauge avoided air bubble problem & also it allowed development of pressure fully. Also, the apparatus allows accurate determination of friction torque and determination of oil flow. Rotating pressure gauge gives polar pressure distribution. The graph of coefficient of friction vs. bearing modules can be drawn which demonstrates the boundary and fluid film lubrication.The apparatus is accurate and simple means to study a practical journal Bearing.

JOURNAL BEARING APPARATUS, We also manufacture the equipments and control systems for sugar industries mainly mill automation, boiler instrumentation, prd stations and embibition water control system.

• diameter: 50 mm

Simple Demonstrations: Observation of the pressure profile at the various conditions of load and speed. Experimental Investigation: After noting the pressure profile for any chosen conditions the following analysis may be conducted. Plotting the Cartesian and polar pressure curves.

The unit consists of a motor driven journal shaft mounted in bearings over which a bearing floats. Oil is supplied to bearing by gravity feed, from oil supply tank. The motor is provided with speed control. In order to avoid clumsiness & height limitation problems with ordinary oil tube manometers, a pressure gauge is provided, which is connected to a tapping over the bearing. The tapping can be rotated to required angular position around the journal axis, so that pressure distribution around the bearing can be noted. A torque arm and weights provided enable to measure the friction torque. Weight set is provided to load the bearing. Thus experiments can be conducted at various loads & speeds. Due to rotating pressure gauge, high pressures can be measured, avoiding overflow and air bubble problems of conventional oil manometer type units. Also, an accurate determination of graph of coefficient of friction Vs. Sommer Feld number is possible, which is useful to decide whether the bearing is operating in boundary lubrication or oil film lubrication. SPECIFICATIONS Journal dia- 49.8.mm, length 50mm. Bearing dia – 50 mm. Pressure gauge – 10 Kg/cm2. Weight set to load the bearing upto 25 Kg. D.C. motor with variable speed control to drive journal. Torque arm and weights for measurement of friction torque. Oil outlet flow measurement arrangement. Thermometer to measure oil temperature.  

We are offering journal bearing apparatus (tom-07). the apparatus consists of a plain steel shaft excavated in a bearing and directly driven by a fhp motor. The bearing is freely supported on the shaft and sealed at the motor end. The speed of the motor is controlled accurately by the speed control unit and it can be made run in both directions. Twelve equal-spaced pressure taping around the circumference and four along the axis are provided and are connected to manometer by pu tubing so that the pressure head of oil in all tubes can be observed at a time. The bearing can be loaded by attaching weights to the arm supported beneath it. Experiments to study the pressure profile of lubricating oil at various conditions of load and speed plotting the cartesian polar pressure curves to measure the frictional torque and power transmit utilities required electric supply : 230 v ac, single phase. Bench area : 1.5 x 1.5 x 4 m tachometer to find out rpm of journal oil sae 40 about 5 ltrs.

• Certification: CE Certified, ISO 9001:2008
• Weight: 10-20kg, 20-30kg, 30-40kg, 40-50kg
• Condition: New, Used
• Capacity: 20L/Hr, 40L/Hr, 60L/Hr
• Power: 0-100W, 100-200W, 200-400W, 400-800W, 800-1600W
• Driven Type: Electric
• Warranty: 1yrs, 2yrs, 5yrs
• Application: Laboratory
• Automation Grade: Automatic, Fully Automatic, Manual, Semi Automatic
• Voltage    : 110V, 220V

EEE Journal Bearing apparatus for investigating the distribution of pressure in slide bearings illustrates the principle of hydrodynamic lubrication. The distribution of pressure and the carrying capacity can be determined on a sliding bearing model at different bearing loads and speeds. The sliding bearing consists of a bearing journal driven by an electrical motor and the freely moving bearing housing. The bearing is loaded with different, interchangeable weights. The setup contains manometer tubes, dc motor, dc drive to control speed, set of weights, oil tank, Journal bearing along with the shaft. Product Code : SAMS DYN - 011

• MODEL NO: TOM-106

The apparatus consists of a plain steel shaft excavated in a bearing and directly driven by a FHP Motor. The bearing is freely supported on the shaft and sealed at the motor end. The speed of the motor is controlled by the speed control unit. One compound pressure gauge is mounted on Bearing to measure the pressure at different position around the circumference. Bearing are free to rotate and can be adjusted at any position of circular scale. The bearing are loaded by attaching weights to the arm supported beneath it.

DESCRIPTION :The apparatus consists of a plain steel shaft encased in a bearing and directly driven by a small electric motor. The bearing is freely supported on the shaft and sealed at the motor end.The motor speed is precisely controlled and adjusted by specially designed control unit and can be run in both the directions.The bearing contains twelve equispaced pressure lappings around its circumference and four additional ones along its topside and on a vertical radial plane. All are connected by light and flexible plastic tubes to the rear manometer panel so that pressure head of aoil at all sixteen points can be clearly observed at all times.Oil is supplied to a low pressure region at both ends of the bearings by an adjustable resevoir fitted at the side of the rear panel.The bearings can be loaded by attaching various weights to the arms supported beneath it.A label is conveniently provided at the front of the apparatus.

• Electric supply: 230 V AC, Single Phase.
• Bench area: 1.5 x 1.5 x 4 m.
• Experiments: To study the pressure profile of lubricating oil at various conditions of load and speed,To measure the frictional torque and power transmit,Plotting the Cartesian polar pressure curves.

Our firm is affianced in manufacturing, exporting and supplying pristine quality Journal Bearing Apparatus. This apparatus is manufactured by utilizing high grade components and innovative technology as per the guidelines laid down by our professionals.

Journal Bearing Apparatus, Reid Vapour Pressure Apparatus, Humidity Chamber

Journal Bearing Apparatus, 5.0 Megapixel Research Microscope Camera

Journal Bearing Apparatus, Mechanical Engineering Lab Equipment