Liquid Level Sensors Dealers

• Power rating: 220V AC

System comes with a sensor that monitors two level of water. The upper level and lower level. User can adjust the level by adjusting the length of cable between weight and float. System switches on the pumping motor as and when water level in the tank falls below the lower level. Water level will starts rising in the tank. As water reaches the upper level set by user, motor will switch off.

We are offering liquid level sensor. Agecho ultrasonic sensors salient features: • agecho ultrasonic sensors are available with output options such as analog current 4-20ma,analogue voltage 0-5v,onoff signal, trigger output for multi-sensor application, pulse width ,serial ttl ,serial rs 232c. • agecho sensing range: 200mm to 1000mm … up to … 6000mm. (19.7feet) (0-200mm is dead band). • agecho accuracy is 1% of the full scale. • agecho operating voltage 12v dc, with reverse polarity protection.(24v dc optional) • agecho is very useful non-contact type of sensing or presence or counting of object. Onoff type signal is also available. • agecho is self-calibrated. Microcontroller is present in each sensor. This provides direct distancedepth reading with better calibration and communication with the controller module. • agecho is very easy to install, rugged design for use in dusty and humid conditions, suitable for outdoor as well as indoor use. • agecho very useful for non-contact distancelevel measurement. The distance of the target is measured, not just its presence, but gives directly 4-20ma, serial or pulse width data proportional to the distance of the target. • agecho operating temperature 0 to 65 degree celsius. • agecho temperature compensated measurement for better accuracy (optional). • agecho unaffected by ambient light, object color or any other optical characteristic. Works with hard materials like metal sheet, plywood, or soft materials like cloth and paper, rubber etc.

Overflowing of tanks and containers can cause a lot of wastage. The wireless liquid level sensor senses the depth of the liquid in real-time and sends alerts when the level exceeds the required level.

• Category: Capacitive Fluid Level Sensors
• Actuation: Capacitive
• Backlighting:: Backlighting:

Capacitive Fluid Level Sensors easily mount to the outside of a container and measure through almost any non-metallic material. They are custom designed and optimized for a range of applications such as medical devices, pump controls, beverage machines etc. A design can use a traditional printed circuit board for a flat surface, or a thin, flexible circuit to accommodate curved surfaces or space-constrained applications. The sensor includes customized embedded software which can be configured for auto-calibration for easy installation, or manual calibration to maximize the accuracy.

• Type: Liquid Level Sensor
• Material: Metal
• Application: Liquid Levelling
• Weight: 0-300gm
• Color: Metallic
• Frequency: 50Hz

Liquid Level Sensors use a photo-transistor trigger that provides a digital output. These sensors incorporate reverse polarity, over voltage, short circuit and transient protection. We are counted among the top Suppliers of Liquid Level Sensors. We have developed a vast distribution network, due to which, it has become easy for us to deliver retail as well as bulk orders for Liquid Level Sensors within the committed time frame. Details Maximum scan range is 6 m Sealing to IP67 M12 connector, 5 pin Visual indication Four output options; analog (0 Vdc to 10 Vdc and 4 mA to 20 mA) and 2 PNP or 2 NPN switching outputs Synchronizing/hold input Two switch point adjustment via teach-in sequence Temperature compensation Easy installation Not affected by dust, light, and color CE and UL/CSA approved  

We are offering following Liquid level sensor a. Hydrostatic liquid level sensors b. Capacitive liquid level sensors c. Optical liquid level switche

• Type: Bottom Loading Magnet System from AMI
• Voltage: 110V, 220V
• Condition: New
• Automatic Grade: Automatic
• Driven Type: Electric
• Power Supply: 3-6kw, 6-9kw
• Load Capacity: 10-50ton
• Warranty: 1year

• Feature: Fine finish, Durability, Precise design, Rugged, Low maintenance, High performance

• Material: non-metal
• Weight: 70g
• Brand: Koino
• Sensor Type: Proximity
• Model Name/Number: KLS-3A
• Connector Type: Mount to Bypass Type
• Power supply voltage: 12-24VDC
• Current Consumption: 10mA
• Timer: 0-3 Second
• Indicator: LED
• Protection Degree: IP66
• Insulation Resistant: 50 M ohm
• Dielectric Strength: 500 VAC

• Accuracy: +/- 1%
• Usage: Industrial
• Operating Current: 20-40 amp
• Voltage: 220-240 V
• Power: 2 Watts(5 watts peak)

Liquid level sensor The drop float actuator allows the switch housing and float pivots to be located above the surface of the liquid and provides normally closed switch contact, opening as the liquid level rises. They are manufactured in a variety of materials, with a choice of gasket materials, to suit most commonly used liquids.

The Model 150A is a lightweight, hand-held meter for use with helium storage dewars on loading docks or in storage rooms, or in remote helium level operations where line power is unavailable. The Model 150A includes a 3.5 digit LCD display with readout accuracy of 0.5%, and a push-to-read switch that allows level measurements to made within seconds. The Model 150A is designed for use with AMI liquid helium level sensors up to 60" in active length. Battery powered convenience The unit is powered by a rechargeable, sealed lead-acid battery pack. The battery pack provides capacity for hundreds of readings between recharges. Also, a Model 150A with fully-charged batteries can be stored for up to a year at room temperature before battery recharging is required. The Model 150A is shipped with a battery charger.

• Output: 20 mA
• Frequency: 50 Hz
• Weight: 3.2 kg
• Head Protection Class: IP67
• Temperature Range: 85 Degree Celsius
• Pipe Length: 1.2 feet
• Pipe Material: Stainless Steel
• Supply Voltage: 220 V
• Usage/Application: Used to monitor and regulate levels

• Material: Metal
• Frequency: 50-60 Hz
• Usage/Application: Liquid Level Measurement
• Voltage: 120 V
• Current: 1-10 A
• Packaging Type: Packet

• Minimum Ambient Temperature (C): -30°C
• Maximum Ambient Temperature (C): 50°C

The sensor�s microprocessor also functions as a controller, enabling the direct control of a modulating motor valve, thereby bypassing the external controller or the PLC. The controller can be set up with all the parameters that are necessary for regulating a modulating motor valve or a stepper motor valve. The sensor is available with a cable for direct supply to and control of the motor valve, or as a sensor where the signal is sent to the external controllerPLC.

• Accuracy: +/-1 %
• Operating Temperature: Up to 125 Degree C
• Working Pressure: 10 kg/sq.cm
• IP Rating: IP68
• Resolution: 5 mm