Mixing Valves Dealers

• Type: 3 Way
• Working Pressure: Upto 42 Bar
• Media: Air / Steam / Water/Gas /Oil /Chemical
• Size: 40MM To 50MM
• Valve Body: IC CFB
• Working Parts: IC CFB
• Seat: PTFE
• Pneumatic Pressure: Upto 3.5 to 7 Bar
• Temperature: Upto 180 Degree C Maximum
• Ends Connection: Scrwed End BSP (F)

• Brand Name: Star Soda machines

We are distributing Postmix valves to the manufacturer which have been used in soda machines. We have all the three brands of Lancer, Cornolius and Flowmatic valves. We have huge quantity of valves.

• Size: DN20 mm
• Material: Brass
• Max Pressure: 10 bar
• Packaging Type: Box
• Control Range: 90 Degree C

MAIN CHARACTERISTICS AND USES The RA thermostatic mixings valves are used in hot water systems for sanitary use. They keep the temperature of mixed water supplied to the user constant even when the condition listed below vary: Temperature Supply pressure Incoming hot and cold water flow The RA thermostatic mixing valves have a temperature range that is ideal for heating a centralized water system with heater . They also have an internal anti-limestone lining.OPERATION : The valves were designed to supply domestics hot water at an adjustable and constant temperature where no other regulating system is present. The very sensitive thermostatic elements is positioned centrally inside the out going stream union and its guides a regulating shutter which adjusted the ingoing cold water flow to the hot water flow according to the required water temperature . The knob can be used to regulate the temperature of the outgoing water. MATERIALS : Shutter - Brass Body - Brass Tap - Brass Spring - Stainless steel Knob - PA6

Vehicle : Scorpio

We are comfortable with online and traditional payment methods. Our policies related to payment procedures are transparent. We believe in professionally managing payment agreements. A famed name, the company is entrusted with a task of making available high quality lot of thermostatic mixing valve.

HAT/MIX valves can be used in any application in which a constant low flow rate (under 1 GPM) of water at a specific temperature is desired. These valves, like any mixing valve, must be installed with check valves on both hot and cold inlets. Pressure reducing valves are recommended on HAT/MIX installations in which system pressures are likely to vary. Pressure reducing valves should be adjusted to approximately 10-20% less than average system pressure for accurate and constant outflow temperatures. In some installations, throttling valves may be used in place of pressure reducing valves. These throttling valves should be set and locked for safety.   Design Features * Condensate temperature baths* Batching* Constant temperature basins & sinks* Water circulation systems* Low flow direct injection water heating (under 1 GPM)* Make-up water* Hot water tracing

• Features: Long lasting shine, Superior quality, Perfect finish

• Media: Steam, chemical, fluid
• Material: Stainless Steel
• Brands: Aira, Avcon
• Model No.: 3ALCS
• Size Inch: 1/2" to 4"
• Pressure: 4 to 7 Bar
• Temperature: Upto 220 deg C
• Ends: Flanged, Screwed
• Usage Application: Pharmaceutical plants, Food processing plants

• Media: Air, Water, Oil, Gas, Steam & Chemical
• Size: 1/2″ to 3″ Screwed / Flange
• Body: ASTM A351 Gr. CF8 / CF8M / CF3M
• Steam Packing: PTFE upto 180°C, Self-compensating (Spring Loaded)
• Trim / Spindle: Stainless Steel 304/316/316L
• Seat: Soft Seat (PTFE)
• Gland Packing: Teflon ‘V’ seals, backed by graphite wiper seal (Self Compensating)
• Body Test Pressure: 42 Bar Maximum
• End Connections: Female Screwed to BSP or NPT / Flange / Triclover
• Working Fluid Press: Drop tight / bubble tight, class IV ANSI B 16, 104, 1976
• Leakage: On steam – Continues 155°C, Intermittent 180°C Maximum
• Operating Temp.: (High Temp. above 180°C – On Request)

• Media: Water
• Material: Aluminum
• Pressure: High Pressure, Medium Pressure
• Control range: Up to 65 degree C
• Max Pressure: 10 bar
• Pay Mode Terms:  L/C (Letter of Credit),T/T (Bank Transfer),Other

We facilitate trade by providing you varied payment options like payment through online as well as offline modes. We understand that high-quality standards should be maintained throughout the offerings. And, for attaining this objective, we make use of superior-grade raw material for manufacturing the same.

• Size: 3/4 to 2 Inch
• Material: Brass
• Features: Durability, Finely finished,Rust proof
• Temperature: -10 to +260 deg C

We are among the chief Mixing Valves Manufacturers in the country. Our Mixing Valves are famous for their fine quality and high working capacity. We make Thermostatic Mixing Valves of supreme quality. Power Mixing Valves are also our speciality.

The Coolant Mixing Valve is used for the accurate mixing of coolants for a measured performance. It relies on mixing zone design that helps in creating the strong waves of water vapor, which in turn breaks down the coolant concentrate into a homogeneous solution. The resultant fluid is good on stability with high lubricity and tramp oil rejection. The flow rate is based on operating water pressure and it is incorporated with semi-concealed metering screw for fine adjustment of mixing ratios.The Coolant Mixing Valves are mounted on drums and homogeneously combines the fluid concentrate with water in accurate ratios. Made from non corrosive stainless steel material it is simple to operate. Installation The Coolant Mixing Valve is installed by connecting it to the pressurized water supply. It comes with water inlet attachment and outlet hose that simply switches the water on and off and controls the mixer. Dilution Range : 0.5% - 15%Maximum Flow Rate : 30 LPMAvailable Capacities : 205, 25 and 20 liters Applications Adjustable mixing ratio Sturdy structure Simple to operate Excellent implosion prevention   Models available: Standard Coolant Mixing Valve for drums having capacity of 250 liters Model featuring short feed hose and drum adaptor for the drums having capacities 20 liters and 25 liters. This model is designed with neck adaptor to prevent implosion while drum gets empty

• Installation orientation: As required
• Hot water inlet temperature: Maximum 90 °C
• Connection sizes: G 3/4"
• Setting range: 30 °C to 60 °C
• Flow rate at 1.0 bar pressure differential across valve: 25 litres / min
• Control accuracy: < ± 4 K

TM 50 thermostatic mixing valves provide control of the water temperature and are used: For centralised control on hot water supply units or for localised control adjacent to point-use outlets. Or for use with solar-heated hot water units with dual energy source. In heating systems with underfloor heating or for limiting boiler return temperatures. Where a system includes a hot water circulation circuit, a KB 191 return flow retarder unit (see accessories) must be fitted to prevent cold water backfeeding and cooling the mixed water at the outlets. Special Features! Highly sensitive thermal element with good all-round water temperature sensing, even at low flow rates! Simple setting of the required water temperature! Scald protection - the hot water inlet is automatically cut off if the cold supply fails provided that the hot water inlet temperature is at least 10 K higher than that of mixedwater setting! The cold water inlet is automatically cut off if the hot supply fails! Inner components are of scale-resistant materials! Complies with KTW requirements Range of ApplicationFlow medium: WaterOperating pressure Maximum: 10 barMaximum pressure difference between hot and cold inlet supplies: 2.5 bar

The thermostatic mixing valves Aquamix Series 61C, 62C and 61CM are offered in versions with male and female connections as well as 4 setting positions. The valve body is made of brass nichel-plated on both inside and outside; moreover an inner teflon coating is provided in order to reduce scaling caused by hard water. Each valve is provided with two mesh strainers which, when inserted inside the hot water (+) and cold water (-) ports avoid depositing of coarse particles thereby protecting valve operation. Main features Available with male and female connections � 2 ranges of adjustment (32-50 °C 42-60 °C) � 4 setting positions In accordance with following standards: � UNI 975390 "Control valves for heating systems" � BSI 1415 British standards (Anti-scalding safety)